ZXP Series 7 User's Manual (en) - Hant

More documents

Recommendations

Info

5: ZXP Series Toolbox Configuration Printer Settings The Printer Settings screen allows you to change the OCP settings, set the network configuration parameters, change print performance settings, adjust the print offset and image fill, and change the printhead serial number and resistance. Note • Access to Print Adjustment and Print Head options is controlled via Advanced Security > Security Roles. • OCP: This section allows you to change the Language displayed in the Operator Control Panel (English, French, Spanish, German, Portuguese, or Italian) and adjust the LCD Contrast level selected (the level ranges from 20 to 50). • Network Configuration: This section allows you to change the various network configuration parameters (DHCP, SNMP, IP address, Gateway, and Subnet mask). Note that the MAC address cannot be changed. 104 Zebra ZXP Series 7 Card Printer User’s Manual P1036101-001
5: ZXP Series Toolbox Configuration • Print Performance Setting: Performance options from the dropdown menu include: - No error recovery (None): The printer provides high throughput with a hands-off error recovery policy. This allows the host to have full control over how failed jobs are retried, if at all. In this mode, there can be more than one job in the system at any time. If there is any job in the system (i.e., printer or laminator) and an error occurs, the job will not be automatically retried by the system after the error is cleared. In addition, jobs already in the printer that were sent after the job that had the error are aborted. Jobs ahead of the one with the error are not affected and are allowed to proceed to completion if possible. This mode would be used in applications requiring, for example, uniquely-serialized cards and having no automated means of validating the mating of a job to a card. - Standard error recovery (Medium): The printer provides high throughput with a reasonable-effort error recovery policy. In this mode, there can be more than one job in the system at any time. If a job suffers an error it will be automatically retried after the error is cleared. Card jams, for example, are handled this way – after the printer is opened, the jammed card removed, and the printer closed and re-initialized, a fresh card is fed and the job reprocesses without host intervention. Jobs ahead of the job that had the error are not affected and are allowed to proceed to completion if possible. Jobs behind the one with the error are paused until the error is cleared, and then they also proceed to completion. - Full error recovery (High): The printer provides reduced throughput so that it can recover any job automatically. In this mode, only one job is allowed into the system at a time; and if a job errors anywhere in the system, the job will automatically be retried by the system after the error is cleared. • Print Adjustment Adjust the Print X offset and Print Y offset sliders to position the image on the card. The Print X offset slider values range from -150 to +150. The Print Y offset slider values range from -16 to +16. Note that changing the offset can cause the printer to print off the edge of the card and cause ribbon ripping. Image Fill is used to resize the image (smaller or larger) to best fit the card. • Print Head (Access is controlled via Security Roles) - Serial Number: When you replace the printhead, change this field to match the serial number of the replacement printhead. - Resistance (Minimum: 2200 ohms, Maximum: 3300 ohms): When you replace the printhead, change this value to match the resistance of the replacement printhead. Note that the values must be the same for the algorithms to work properly. This value is located on a sticker on the printhead; e.g., R = 3000. The Save Settings button saves any changes you have made to this screen. The Advanced Setting button provides access to service-related tests and adjustments. Use is password protected and limited to Zebra-authorized service personnel. P1036101-001 Zebra ZXP Series 7 Card Printer User’s Manual 105
Page 1 and 2:
ZEBRA ZXP SERIES 7 User’s Manual
Page 3 and 4:
Contents 1 • Introduction . . . .
Page 5 and 6:
1 Introduction Description This Man
Page 7 and 8:
1: Introduction Icons Icons Through
Page 9 and 10:
2 Installation and Setup General In
Page 11 and 12:
2: Installation and Setup Unpacking
Page 13 and 14:
2: Installation and Setup Unpacking
Page 15 and 16:
2: Installation and Setup Loading C
Page 17 and 18:
Installing the Dual Cleaning Cartri
Page 19 and 20:
Installing the Manual Feed Cleaning
Page 21 and 22:
2: Installation and Setup Loading a
Page 23 and 24:
2: Installation and Setup Loading a
Page 25 and 26:
2: Installation and Setup Loading t
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
2: Installation and Setup Connectin
Page 39 and 40:
2: Installation and Setup Connectin
Page 41 and 42:
2: Installation and Setup Installin
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
3 Operation Introduction Printing w
Page 55 and 56:
3: Operation Manual Card Feed Manua
Page 57 and 58: 3: Operation Operator Control Panel
Page 67 and 68: 4 Printer Settings and Adjustments
Page 69 and 70: 4: Printer Settings and Adjustments
Page 97 and 98: 5 ZXP Series Toolbox Introduction I
Page 99 and 100: 5: ZXP Series Toolbox Information I
Page 101 and 102: 5: ZXP Series Toolbox Information M
Page 103 and 104: 5: ZXP Series Toolbox Configuration
Page 105 and 106: 5: ZXP Series Toolbox Configuration
Page 107: 5: ZXP Series Toolbox Configuration
Page 111 and 112: 5: ZXP Series Toolbox Cleaning Clea
Page 113 and 114: 5: ZXP Series Toolbox Technology Te
Page 115 and 116: 5: ZXP Series Toolbox Technology Sm
Page 117 and 118: 5: ZXP Series Toolbox Advanced Secu
Page 119 and 120: 5: ZXP Series Toolbox Advanced Secu
Page 121 and 122: 6 Cleaning Caution • PROTECT YOUR
Page 123 and 124: 6: Cleaning Cleaning the Printer Cl
Page 125 and 126: 6: Cleaning Cleaning the Printer Po
Page 127 and 128: 6: Cleaning Cleaning the Laminator
Page 133 and 134: 6: Cleaning Dual Cleaning Cartridge
Page 135 and 136: 7 Troubleshooting Introduction The
Page 137 and 138: 7: Troubleshooting Introduction COD
Page 143 and 144: 7: Troubleshooting Ethernet Etherne
Page 145 and 146: 8 Technical Specifications Standard
Page 147 and 148: 8: Technical Specifications Specifi
Page 149 and 150: 8: Technical Specifications Specifi
Page 151 and 152: 8: Technical Specifications Agency
Page 153 and 154: 8: Technical Specifications Declara
Page 155 and 156: APPENDIX A Printer Configurations I
Page 157 and 158: Appendix B Connecting to a Network
Page 159 and 160:
B: Connecting to a Network Setting
Page 161 and 162:
B: Connecting to a Network Step 13.
Page 163 and 164:
B: Connecting to a Network Printer
Page 165 and 166:
Appendix C Accessing a Network Prin
Page 167 and 168:
C: Accessing a Network Printer via
Page 169 and 170:
Appendix D Magnetic Card Encoder In
Page 171 and 172:
D: Magnetic Card Encoder Printing O
Page 173 and 174:
D: Magnetic Card Encoder Functional
Page 175 and 176:
D: Magnetic Card Encoder AAMVA The
Page 177 and 178:
APPENDIX E Smart Card Options Intro
Page 179 and 180:
E: Smart Card Options External Cont
Page 181 and 182:
APPENDIX F Worldwide Support For Te
Page 183 and 184:
F: Worldwide Support Asia Pacific -
show all

ZXP Series 7 User's Manual (en) - Hant

Create successful ePaper yourself

Delete template?

Save as template?