SDU-xcite Smart Display Unit Installation Instructions - Trend Controls
SDU-xcite Smart Display Unit Installation Instructions - Trend Controls
SDU-xcite Smart Display Unit Installation Instructions - Trend Controls
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
100-240 V<br />
1 2 3<br />
1 + 0<br />
4 5 6<br />
2 + 0<br />
7 8 9<br />
3 + 0<br />
10 11 12<br />
4 + 0<br />
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30<br />
5 6<br />
7 8<br />
9 10<br />
+ 0 + 0 + 0 + 0 + 0 + 0<br />
OK RX<br />
24 V<br />
A<br />
0 V<br />
24 V<br />
P<br />
11 12 13 14 15 16<br />
P 0 P 0 P 0 P 0 P 0 P 0<br />
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48<br />
<strong>SDU</strong>-<strong>xcite</strong><br />
<strong>Installation</strong> <strong>Instructions</strong><br />
3 <strong>Installation</strong> (Continued)<br />
7<br />
Connect to IQ3<br />
Note that supervisor port address should set to zero (default)<br />
Note that label lengths should be restricted to a maximum of 20 characters<br />
IQ3<strong>xcite</strong><br />
RD/<strong>SDU</strong>-IQ2COMMSCABLE/3M<br />
RD/<strong>SDU</strong>-IQ2COMMSCABLE/10M<br />
<strong>SDU</strong>-<strong>xcite</strong><br />
rear view<br />
local supervisor<br />
port<br />
RJ11<br />
RJ11<br />
maximum distance 25 m (28 yds)<br />
+<br />
If required a cable can be made to the required length, wired as below<br />
25 m (28 yds) maximum<br />
<br />
$<br />
#<br />
!<br />
"<br />
4 4 <br />
"<br />
!<br />
#<br />
$ <br />
Note that the IQ controller may be connected while powered; if not power up controller.<br />
8<br />
Mount <strong>Unit</strong><br />
60 mm<br />
9<br />
Replace Cover<br />
standard UK electrical or panel<br />
back box<br />
60 mm<br />
50 mm<br />
46 mm<br />
2 off Ø4 mm<br />
(M3.5 x 30 mm screws provided)<br />
Ø4 mm<br />
(M3.5 screw)<br />
10<br />
Check Start Up Reset<br />
1 2 3 4<br />
Communications failure<br />
<strong>SDU</strong>-<strong>xcite</strong> V1.0<br />
<strong>Display</strong>s first labelled sensor<br />
- if set to defaults<br />
5 A I H <br />
. H 5 F = A 6 A F<br />
! , A C +<br />
Firmware version<br />
4<br />
<strong>SDU</strong>-<strong>xcite</strong> <strong>Installation</strong> <strong>Instructions</strong> TG200643 Issue 1/E 20/11/06