The Installation Handbook - Howarth Timber

More documents

Recommendations

Info

WALL LINING: GTEC Dryliner 150mm GTEC Dryliner Track RD9 Snipped and folded to form header 600mm 2 3 GTEC Dryliner Track 800mm 300mm GTEC Metal Angle 90 or GTEC Dryliner Track RD9 GTEC Dryliner Channel GTEC Dryliner Track External corners Position the brackets as close as possible to each side of the corner. At corner, attach GTEC Metal Angle 90 MFC2330 vertically to horizontal floor and ceiling Dryliner Tracks with GTEC Wafer Head screws. 20 THE INSTALLATION HANDBOOK 2008
Insulation Existing Wall Insulation - slit locally and slide behind channels Plasterboard Where required, insert mineral wool batts between the GTEC Dryliner Channels. To ensure that the batts continue behind the GTEC Dryliner Channels as an unbroken lining, slit the batts locally and slide across each GTEC SR Bracket. <strong>The</strong> use of GTEC Vapour Board should be considered to control condensation. Movement control joints GTEC Movement Control Joint Movement control joints are required in wall linings at intervals not exceeding 10m, and where the drylining crosses or abuts a structural movement joint. At movement control joints leave a 12.5mm opening between the plasterboards and use GTEC Dryliner Channels on each side of the joint to support the plasterboard edges. Cut GTEC Movement Control Joint to length. Butt joint lengths end to end where necessary. Attach to the board surface with 13mm stainless steel staples at 150mm centres. Apply GTEC Joint Filler or GTEC Allset, feathering out the edges of the second coat. After finishing, remove the masking strip from the centre of the joint. Internal Corners Where it is not possible to screw-fix one of the GTEC SR Bracket legs to the GTEC Dryliner Channel RD1, bend back the teeth of the GTEC SR Bracket RD2 so that they engage with the corner of the GTEC Dryliner Channel as shown and screw fix. Construction around doors 1. At ceiling level, continue ceiling GTEC Dryliner Track across the door head. At floor level, turn floor GTEC Dryliner Track into reveals and butt against the door frame as shown. Fix the GTEC Dryliner Track RD9 to inside face of door frame with suitable fixings as shown. Internal Corners 2. To form the external corner of each door opening, cut GTEC Dryliner Track 5mm less than floor-to-ceiling height. Cut back flange at uppermost end of GTEC Dryliner Track and fix to ceiling and floor GTEC Dryliner Tracks with GTEC Wafer Head Self Tapping screws. 3. To form door head member use a section of GTEC Metal Angle 90 MFC2330 or GTEC Dryliner Track RD9 snipped and folded as shown. Attach to the vertical GTEC Metal Angles with GTEC Wafer Head Self Drilling screws. GTEC Dryliner Track Door reveal lining assembly THE INSTALLATION HANDBOOK 2008 21
Page 1 and 2: PLASTERBOARD The Backing of a World
Page 3 and 4: Introduction
Page 5 and 6: What are the values of GTEC The GTE
Page 7 and 8: Environmental Policy Fulfilling our
Page 9 and 10: The Lafarge GTEC Direct Bond System
Page 11 and 12: Table 2: Use of GTEC Universal Bond
Page 13 and 14: 4 Apply vertical dabs at required c
Page 15 and 16: The Lafarge GTEC Wall Lining System
Page 17 and 18: STUD Max. Height Guidance Table (m)
Page 19 and 20: 4 Using a disc cutter, drop-saw or
Page 21: The Lafarge GTEC Dryliner System is
Page 25 and 26: 4 Cut each GTEC Dryliner Channel RD
Page 27 and 28: The Lafarge GTEC Metal Stud System
Page 29 and 30: Table 1: Components for Metal Stud
Page 31 and 32: 4 Place the ceiling GTEC U Track on
Page 33 and 34: 10 Form as required, one of the fol
Page 35 and 36: The Lafarge GTEC Acoustic Homespan
Page 37 and 38: Skirting Detail A GTEC U Track onto
Page 39 and 40: 4 Place the ceiling GTEC U Track on
Page 41 and 42: 10 Fix the GTEC Acoustic Homespan b
Page 43 and 44: For fixing GTEC plasterboard to tim
Page 45 and 46: GTEC Intumescent Acoustic Sealant a
Page 47 and 48: The Lafarge GTEC Direct to Timber S
Page 49 and 50: Single-layer Boarding Noggins Note:
Page 51 and 52: The Lafarge GTEC Acoustic Floor Sys
Page 53 and 54: GTEC Metal Angle GTEC Acoustic Floo
Page 55 and 56: 4 Fix self adhesive GTEC Resilient
Page 57 and 58: The Lafarge GTEC Dryliner System is
Page 59 and 60: Upgrading existing timber joist flo
Page 61 and 62: 4 Cut the GTEC Dryliner Channel RD1
Page 63 and 64: The Lafarge GTEC Suspended MF Ceili
Page 65 and 66: GTEC Primary Channel GTEC Connectin
Page 67 and 68: 4 Secure the GTEC Ceiling Channels
Page 69 and 70: The Lafarge GTEC T-Bar Corridor Sys
Page 71 and 72: 60 x 60mm rock mineral wool batt TO
Page 73 and 74:
3 Position the boards with long edg
Page 75 and 76:
The Lafarge GTEC T-Bar Flat Ceiling
Page 77 and 78:
GTEC T-Bar Primary Main T 60x60mm r
Page 79 and 80:
4 Fix GTEC T-Bar Cross T TC1200 to
Page 81 and 82:
Lafarge GTEC Taping and Jointing Sy
Page 83 and 84:
Square and Cut Edge Joints External
Page 85 and 86:
4 Internal Angles When set hard and
Page 87 and 88:
10 Square Edge Joints When set hard
Page 89 and 90:
Lafarge GTEC Taping and Jointing Sy
Page 91 and 92:
GTEC Cove is a simple and cost effe
Page 93 and 94:
5 100mm GTEC Cove bonded with GTEC
Page 95 and 96:
Instructions for marking and cuttin
Page 97 and 98:
THIS IS THE CEILING EDGE GTEC Cove
Page 99 and 100:
A guide to the GTEC Plasterboard So
Page 101 and 102:
GTEC E Board Designed for use in dw
Page 103 and 104:
GTEC drywall screws are designed sp
Page 105 and 106:
Screws SELF TAPPING SCREWS GTEC Sel
Page 107 and 108:
Screws HIGH THREAD SCREWS GTEC High
Page 109 and 110:
GTEC Ready Reckoners give a quick g
Page 111 and 112:
Wall Linings: Lafarge GTEC Dryliner
Page 113 and 114:
Floors and Ceilings: Lafarge GTEC S
show all

The Installation Handbook - Howarth Timber

Create successful ePaper yourself

Delete template?

Save as template?