download pdf - Glassline GmbH

RAILINGSYSTEMS
PLANNING MANUAL
EFFICIENCY DECIDES

THE SYSTEM
The system that can even be
without any load-bearing
handrail ... *
With general technical approval
(AbP) and certified type structural
properties!
* Requirement for this: LSG-ESG 2x10 mm,
Protection of the glass edge using an edge protector
2 www.glassline.de

THE SYSTEM
TYPE STATIC
AbP
The full glass railing system
with certified type structural properties
from LSG-TSG 2x6 mm
In public and private construction projects
The System
Panel widths of up to 6,000 mm can be achieved
In buildings and outdoors
Panel heights of up to 1,400 mm can be achieved
In flat areas and on stairs
No glass type structural
properties are required!
No additional glass type structural properties
are needed for a variety of different applications!
Measurement tables can be found
starting on page 32.
≤ 6.000 mm
≤ 6.000 mm
≤ 1.400 mm
Glass
Applications
Safety from the Outset
STYPENSTATIK
AbP
General technical approval (AbP)
No more incalculable time and cost factors for inspections or building code conditions. BALARDO ALU
reduces the project period to a minimum and can be used straight away without any red tape.
Handrails
TYPE STATIC
Type structural properties
Benefit from maximum safety thanks to certified type structural properties for a variety of different
applications in private and public areas as well as in buildings and outdoors.
AbP
bP
Certified by the LGA (Landesgewerbeanstalt Bayern)
The type-certified BALARDO ALU system is structurally calculated and the dynamic structural behaviour
for continuous use is tested by means of an extensive series of tests.
There is no need for single-case permission (ZIE)
This means no time-consuming bureaucratic procedures - BALARDO ALU can be put to direct use.
Service
www.glassline.de
3

THE SYSTEM
Impressive Transparency
with a handrail or glass edge protector profile
Glass edge protection in the application
Overview
System-specific glass
edge protector profile
U-profile
Round handrail, 42.4 mm
Round handrail, 48.3 mm
Height 6.0 mm
30 x 27 mm, d = 3.0 mm
ø 42.4 mm, d = 1.5 mm
ø 48.3 mm, d = 1.5 mm
For glass (LSG / ESG)
2 x 10 mm
For glass (LSG / ESG)
From 2 x 6 mm
For glass (LSG / ESG)
From 2 x 6 mm
For glass (LSG / ESG)
From 2 x 6 mm
Technical data, see page 36.
info
4 www.glassline.de

THE SYSTEM
The System
Table of Contents
Profile Overview Page 6
Click n Fix Installation Kit Page 7
System Profile Top1 Page 8
System Profile Top2 Page 10
System Profile Top3 Page 12
System Profile Side1 Page 14
System Profile Side2 Page 18
Accessories Page 22
The System
Applications
Applications
System Application In Flat Areas Page 24
System Application On Stairs Page 26
System Application French Balcony Page 28
Glass
Service Handrails Glass
Glass Page 30
Application and Measurement Tables Page 32
Handrail Installation Page 35
Stainless Steel Handrails Page 36
Wooden Handrails Page 37
Customised Handrail Page 38
Accessories for Stainless Steel Handrails Page 40
Installation Instructions Page 42
Enquiry Form Page 43
Handrails
Service
www.glassline.de
5

THE SYSTEM
≤ 30
Glasbreite 100-6.000*
≤ 30
PROFIL
≤ 30
Profillänge ≤ 3.000
Profile Overview
GLAS
PROFIL
System Profiles for Floor Installation
≤ 30
Glasbreite 100-6.000*
≤ 30
≤ 30
Page 8
≤ 30
GLAS
≤ 30
Glasbreite 100-6.000*
System PROFIL Profile
Top1
≤ 30
Profillänge ≤ 3.000
≤ 30
≤ 30
≤ 30
Page 10
PROFIL
Profillänge ≤ 3.000
System Profile
Top2
≤ 30
Page 12
System Profile
Top3
System Profiles for Lateral Installation
Page 14
System Profile
Side1
Page 18
System Profile
Side2
6 www.glassline.de

THE SYSTEM
Click n Fix Installation Kit
consisting of a clamping shoe, clamp as well as an inner and outer seal
Seals
Inner and outer seal
The System
Material:
EPDM
Length:
approx. 3,000 mm
Clamp
Clamping shoe
Clamp
Material:
Length:
Clamping shoe
Material:
Length:
POM
approx. 300 mm
EPDM
approx. 3,000 mm
Applications
CLICK N FIX
assembly
Revolutionary Fast:
Click n Fix Installation
Glass
The revolutionary Click • n Fix installation kit makes the
installation of full glass railing systems extremely easy:
Insert the glass and place the clamp on the profile.
As soon as you press the panel outwards, it will
“click” and the clamp will fall into its position
and lock the panel in place.
Installation video
www.glassline.de/balardo
Handrails
Press
Ready!
Service
Insert
Click
www.glassline.de
7

THE SYSTEM
7
System Profile Top1
For floor installation
Profile
Material:
Length:
Glass inset:
Aluminium
3,000 mm
approx. 100 mm
Surfaces:
“Natural”
Untreated
Stainless steel effect
(E6/EV1)
Premium
brushed stainless
steel finish
Fixing spacing
108
ø 14
7
108
Drilling pattern
(ø 14 mm)
Private area 1 Public area 2
a = 500 mm
a = 250 mm
88 36
124
108
125 250 250 250 250 250 250 250 250 250 250 250 125
3000
ø 14
7
108
Inner Angle
Innenecke
88 36
124
125 250 250 250 250 250 250 250 250 250 250 250 125
3000
Cover Plate
Außenecke
35
108
200
Innenecke
50
200
50
ø 14
88 36
124
35
Outer Innenecke Angle
200
50
35
108
35
124
35
124
35
124
124
50
124
50
108
200
Außenecke 200
50
35
35
35
124
50
200
35
50
108
124
200
50
200
Innenecke Außenecke
108
200
ø 14
88 36
124
125 250 250 250 250 250 250 250 250 250 250 250 125
35
124
50
50
200
200
200
8 www.glassline.de
200
3000
50
200
35
124
3000
124
125 250 250 250 250 250 250 250 250 250 250 250 125
124
108
200 Außenecke
7
108
200
50
50
50
50
35
108
108
d = 2.0 mm
124
124
self-adhesive
35 35
124
124
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
on pages 22 + 36.
All of our profiles have general technical approval, certified type structural properties and are LGA-certified.
info
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m
108
35
108
108

THE SYSTEM
System Profile Top1
Sample Applications
Sample Application 1 Sample Application 2
The System
Glass height (H) (H) ≤ ≤ 1,400*
Glass height (H) (H) ≤ ≤ 1,400*
Glass height (H) (H) ≤ ≤ 1,400*
Glass height (H) (H) ≤ ≤ 1,400*
Applications
Profile Profile protrusion protrusion
Profile Profile protrusion protrusion
0 - 5 bei 0 - H 5 ≤ bei 1.400 H ≤ 1.400
0 - 5 bei 0 - 5 bei 1.400
1.400
0 - 10 bei 0 - 10 H ≤ bei 1.250 H ≤ 1.250
0 - 10 bei 0 - 10 H bei 1.250 H 1.250
Sample Application 3 Sample Application 4
Glass
Glass height (H) (H) ≤ ≤ 1,400*
Glass height (H) (H) ≤ ≤ 1,400*
On-site On-site
On-site drain On-site drain
drain drain
Drain grate Drain grate
Drain grate Drain grate
Gradient Gradient
Gradient Gradient
Glass height (H) (H) ≤ ≤ 1,400*
Glass height (H) (H) ≤ ≤ 1,400*
Continuous Continuous backfilling backfilling
Continuous
or expanding
Continuous
or expanding
backfilling
mortar
backfilling
mortar
or expanding or expanding mortar mortar
Handrails
* Application and measurement tables, see pages 32-33.
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
www.glassline.de
9

THE SYSTEM
4
System Profile Top2
For Floor Installation
Profile
Material:
Length:
Glass inset:
Aluminium
3,000 mm
approx. 100 mm
Surfaces:
“Natural”
Untreated
Stainless steel effect
(E6/EV1)
Premium
brushed stainless
steel finish
Fixing spacing
132
Drilling pattern
(ø 14 mm)
Private area 1 Public area 2
a = 500 mm
a = 250 mm
ø 14
4
132
60 60
120
132
125 250 250 250 250 250 250 250 250 250 250
3000
250 125
Inner Angle
Innenecke
ø 14
60 60
120
4
132
Cover Plate 3000
125 250 250 250 250 250 250 250 250 250 250
Außenecke
132
250 125
200 200
50 50
132
ø 14
60 60
120
Outer Angle
Innenecke
132
125 250 250 250 250 250 250 250 250 250 250
50
200
200
Außenecke
200 200
50 50
50
120 120
50
200
200
Innenecke
120 120
50
120 120
50
50
200
3000
200 200
50 50
Innenecke Außenecke
250 125
120
120 120
132
132
60 60
120
3000
125 250 250 250 250 250 250 250 250 250 250
132
ø 14
Außenecke
200 4 200
50 50
50
200
200
50
132
132
d = 2.0 mm
120
120
self-adhesive
1010 www.glassline.de
120
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
on pages 22 + 36.
All of our profiles have general technical approval, certified type structural properties and are LGA-certified.
info
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m
250 125

THE SYSTEM
System Profile Top2
Sample Applications
Sample Application 1 Sample Application 2
Glass height Glass ≤ 1,400* height ≤ 1,400*
Glass height Glass ≤ 1,400* height ≤ 1,400*
37
The System
Glass height ≤ 1,400*
37
37
Glass height ≤ 1,400*
Glass height Glass ≤ 1,400* height ≤ 1,400*
Continuous Continuous backfilling backfilling
or expanding or mortar expanding mortar
Continuous backfilling
or expanding mortar
Applications
Glass height ≤ 1,400*
Sample Application 3
Glass
Handrails
* Application and measurement tables, see pages 32-33.
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
www.glassline.de
11

THE SYSTEM
System Profile Top3
For Floor Installation
Profile
Material:
Length:
Glass inset:
Aluminium
3,000 mm
approx. 100 mm
Surfaces:
“Natural”
Untreated
Stainless steel effect
(E6/EV1)
Premium
brushed stainless
steel finish
Fixing spacing
132
Drilling pattern
(ø 14 mm)
Private area 1 Public area 2
a = 200 mm
a = 100 mm
ø 14
132
24 24
48
Inner Angle
Innenecke
132
ø 14
24 24
48
50 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50
3000
132
50 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50
3000
Cover Plate
Außenecke
Innenecke
Außenecke
200 200
50 50
200 200
50 50
132
ø 14
24 24
48
Outer Angle
Innenecke
132
50 100 100
200
50
50
50
200
200
200
200
Außenecke
200 200
50 50
1212 www.glassline.de
200
50
200
50
50
3000
48
50
200 200
50 50
132
Innenecke Außenecke
200
132
50
24 24
48
100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50
3000
50 100 100
100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 50
48
132
ø 14
132
132
132
48
48
self-adhesive
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
on pages 22 + 36.
All of our profiles have general technical approval, certified type structural properties and are LGA-certified.
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m
d = 2.0 mm
info

THE SYSTEM
System Profile Top3
Sample Applications
Sample Application 1 Sample Application 2
The System
Glass height ≤ 1,400 *
37 Glass Glass height height ≤ 1,400 ≤ 1,400 * *
37
37
Glass height ≤ 1,400 *
Glass height ≤ 1,400 *
Glass height ≤ 1,400 *
Glass Glass height height ≤ 1,400 ≤ 1,400 * *
Continuous backfilling
or expanding mortar
Continuous backfilling
or expanding mortar
Continuous backfilling
or expanding mortar
Continuous backfilling
or expanding mortar
Applications
37
Sample Application 3 Sample Application 4
Glass height ≤ 1,400 *
Glass height ≤ 1,400 *
Glass Glass height height ≤ 1,400 ≤ 1,400 * *
Glass height ≤ 1,400 *
Glass height ≤ 1,400 *
Glass Glass height height ≤ 1,400 ≤ 1,400 * *
Continuous
Continuous
Continuous
Continuous
Steel frame
Glass
Handrails
Steel frame
Steel frame
Steel frame
* Application and measurement tables, see pages 32-33.
e.g. Side view of
stair stringer
e.g. Side view of
stair stringer
e.g. Side view of
stair stringer
e.g. Side view of
stair stringer
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
www.glassline.de
13

THE SYSTEM
System Profile Side1
For lateral installation
Profile
Material:
Length:
Glass inset:
Aluminium
3,000 mm
approx. 100 mm
Surfaces:
28
LL = 16 x 36
“Natural”
Untreated
Stainless steel effect
(E6/EV1)
Premium
brushed stainless
steel finish
70
56
116
ø 28
ø 28
Innenecke
116
56
116
125 250 250 250 250 250 250 250 250 250 250 250 125
LL = 16 x 36
3000
70
ø 28
70
56
70
50
Inner Angle
LL = 16 x 36
ø 28
Innenecke
200
ø 28
116
116
Drilling pattern
(At the back, oblong hole 16 x 36 mm,
at the front ø 28 mm)
70
ø 28
116
56
LL = 16 x 36
125 250 250 250 250 250 250 250 250 250 250 250 125
70
70
Außenecke
125 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 1250 250 125
125 250 250 250 250
3000
3000
ø 28
Innenecke
200
116
70
50
Fixing spacing
Private area 1 Public area 2
a = 500 mm
a = 250 mm
116
3000
56
Cover Plate
Außenecke
50
200
116
ø 28
56
50
LL = 16 x 36
70
ø 28
Outer Angle
Innenecke
50
200
Innenecke
116
70
200
50
200
50
50
50
50
200
200
200
Außenecke
200
50
200
50
200
50
200
50
200
200
125 250 250 250 250 250 250 250 250 250 250 250 125
3000
116
Außenecke 200
56
120
with facing panel
50
50
50
59
Facing Panel
116
d = 2.0 mm
120
59
self-adhesive
116
56
116
ø 28
120
56
116
56
120
70
59
LL = 16 x 36
56
without
facing panel
Profile Caps *
59
116
70
125 250
200
ø 28
50
200
200
50
120
59
Innenecke
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
50
on pages 22 + 36. All of our profiles have general technical approval, certified type structural properties and are LGA-certified.
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m
info
*
Color silver (similar E6EV1)
200
1414 www.glassline.de
50
200

Ste
Ste
aluminium aluminium 36 x 115 36 x mm, 115 mm,
continuous, continuous, see page see page 22 22
THE SYSTEM
System Profile Side1
Attention! Attention!
Only use Only dowels use dowels with with
a low a dowel low dowel head. head.
Sample Applications
Sample Application 1 Sample Application 2
The System
Continuous Continuous backfilling backfilling
or expanding or expanding mortar mortar
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Applications
Attention! Attention!
Only use Only dowels use dowels with with
a low a dowel low dowel head. head.
Attention! Attention!
Only use Only dowels use dowels with with
a low a dowel low dowel head. head.
Sample Application 3 Sample Application 4
Glass
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Handrails
Steel profile
Steel profile
Steel profile
Steel profile
* Application and measurement tables, see pages 32-33.
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36.
Screw connection to steel profile: e.g. M10 countersunk head with rosette, page 22.
Dowelling: e.g. dowel with internal thread and pre-positioned installation
eight ≤ 1,400*
height ≤ 1,400*
Continuous
*
www.glassline.de
Continuous
Continuous
info
15

THE SYSTEM
Steel profile
Steel profile
Steel profile
Steel profile
System Profile Side1
Sample Applications
Sample Application 5 Sample Application 6
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Steel frame
Steel frame
Steel profile
Steel profile
Sample Application 7 Sample Application 8
Window
frame
Continuous
Window sill
Window
Continuous
frame
Glass height ≤ 1,400*
≤ 1,400* Glass height ≤ 1,400*
Steel frame
Continuous
Steel frame
Continuous
e.g. Side view
of stair stringer
e.g. Side view
* Application of stair and stringer measurement tables, see pages 32-33.
On-site
drain
1616 www.glassline.de
Gradient
Glass height ≤ 1,400*
Glass height ≤ 1,400*
≤ 1,400*
Window sill
Continuous
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
on pages 22 + 36.
Screw connection to a steel frame: e.g. M10 countersunk head with rosette, page 22.
Steel frame
Steel frame
Continuous
info

THE SYSTEM
System Profile Side1
Sample Applications
e.g. Side view
e.g. of stair Side stringer view
of stair stringer
Sample Application 9 Sample Application 10
The System
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Drain grate
Drain grate
On-site
On-site drain
drain
Gradient
Gradient
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Continuous
Continuous
Steel frame
Steel frame
Steel frame
Steel frame
Applications
e.g. Side view
e.g. of stair Side stringer view
of stair stringer
Sample Application 11 Sample Application 12
Glass
Continuous
Continuous
Gradient
Gradient
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Steel frame
Screw connection to a steel frame: e.g. M10 countersunk head with rosette, page 22. Dowelling: e.g. dowel with internal thread and pre-positioned
info
*
Glass height ≤ 1,400*
36
Spacer 30 x 30 x 30 mm Spacer 30 x 30 x 30 mm
at a gap of 250 or 500 mm at a gap of 250 or 500 mm
Space fixing profile - Space fixing profile -
aluminium 36 x 115 mm, aluminium 36 x 115 mm,
continuous, see page continuous, 22 see page 22
Continuous backfillingContinuous backfilling
or expanding mortar or expanding mortar
www.glassline.de
*
Steel frame
*
Glass height ≤ 1,400*
36
Attention!
Attention!
Only use dowels with Only use dowels with
a low dowel head. a low dowel head.
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36.
installation
*
Handrails
Service
17

THE SYSTEM
System Profile Side2
For lateral installation
Profile
Material:
Length:
Glass inset:
Aluminium
3,000 mm
approx. 100 mm
Surfaces:
“Natural”
Untreated
Stainless steel effect
(E6/EV1)
Premium
brushed stainless
steel finish
200
50
200
50
Innenecke
200
LL 16x33
ø 28
LL 16 = x 36
16 x 36
57
Innenecke
200
50
50
LL 16x33
Inner Angle
ø 28
LL =
57
ø 28
Innenecke
Outer Angle
50
ø 28
200
200
57
200
50
125 250 250 250 250 250 250 250 250 250 250 250 125
57
LL 16x33
200
LL 16x33
Drilling pattern
(Oblong hole 16 x 36 mm)
125 250 250 250 250 250 250 250 250 250 250 250 125
200
200
ø 28
50
50
50
200
200
Außenecke
LL 16x33
200
ø 28
Außenecke
200
ø 28
200
3000
200
50
200
LL 16x33
50
LL 16x33
50
50
50
200
Innenecke
ø 28
LL =
16 x 36
Außenecke
200
ø 28
50
50
50
57
ø 28
Innenecke
LL 16x33
Fixing spacing
Private area 1 Public area 2
a = 500 mm
a = 250 mm
200
200
57
50
50
LL 16x33
200
3000
125 250 250 250 250 250 250 250 250 250 250 250 125
Cover Plate
200
ø 28
50
LL 16x33
Außenecke
LL 16x33
200
ø 28
3000
50
LL 16x33
200
200
50
self-adhesive
50
d = 2.0 mm
Außenecke
200
200
200
50
50
50
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
on pages 22 + 36.
All of our profiles have general technical approval, certified type structural properties and are LGA-certified.
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m
info
1818 www.glassline.de

THE SYSTEM
System Profile Side2
Sample Applications
Sample Application 1 Sample Application 2
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Glass height ≤ 1,400* ≤ Glass height ≤ 1,400*
Glass height ≤ 1,400*
The System
Glass height ≤ 1,400* ≤ Applications
Sample Application 3 Sample Application 4
Glass
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Glass height ≤ 1,400* ≤ Continuous backfilling or
Continuous
expanding Continuous mortar backfilling or
Continuous backfilling
expanding
or backfilling
mortar
or
expanding mortar expanding mortar
Glass height ≤ 1,400*
Glass height ≤ 1,400*
Glass height ≤ 1,400* ≤ Steel frame (continuous)
Steel frame (continuous)
Steel Steel frame frame (continuous)
Handrails
Bearing level min. 100 mm.
e.g. Side view of
stair stringer e.g. Side view of
e.g. Side view e.g. of stair Side stringer view of
stair stringer stair stringer
Service
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
info
on pages 22 + 36.
www.glassline.de
19

THE SYSTEM
System Profile Side2
Sample Applications
Sample Application 5 Sample Application 6
Glass height
Glass height
≤ 1,400
≤
*
1,400 *
Glass height Glass ≤ 1,400 height * ≤ 1,400 *
Window
Continuous Continuous
frame
Window Window sill sill
Continuous
Window sill
Continuous
Window sill
Window Window
frame frame
Window
frame
Glass height
Glass height
≤ 1,400
≤
*
1,400 *
Glass height Glass ≤ 1,400 height * ≤ 1,400 *
Continuous Continuous
Continuous
Continuous
e.g. Side e.g. view Side of view of
stair stringer stair stringer
e.g. Side view of
stair stringer
e.g. Side view of
stair stringer
Sample Application 7 Sample Application 8
Glass height
Glass height
≤ 1,400
≤
*
1,400 *
Glass height Glass ≤ 1,400 height * ≤ 1,400 *
Drain grate Drain grate
Drain grate
Drain grate
On-site On-site drain drain
On-site drain
Gradient Gradient
On-site drain
Gradient
Gradient
Glass height
Glass height
≤ 1,400
≤
*
1,400 *
Glass height Glass ≤ 1,400 height * ≤ 1,400 *
On-site On-site drain drain
Continuous Continuous
On-site drain
Continuous
On-site drain
Continuous
Drain grate Drain grate
Drain grate
Drain grate
Steel frame
Steel frame
Steel frame
Steel frame
Gradient Gradient
Gradient
Gradient
Bearing level min. 100 mm.
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
info
on pages 22 + 36.
2020 www.glassline.de

THE SYSTEM
System Profile Side2
Sample Applications
Sample Application 9
The System
Glass height ≤ 1,400*
36
Gradient
Spacer 30 x 30 x 30 mm
at a gap of 250 or 500 mm
Applications
Space fixing profile -
aluminium 36 x 115 mm,
continuous, see page 22
Handrails
Glass
Bearing level min. 100 mm.
Service
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile
info
on pages 22 + 36.
www.glassline.de
21

THE SYSTEM
Accessories
Vertical Glass Edge Protector Profile
System-specific
glass edge protector profile
For glass:
2 x 6 mm
2 x 8 mm
2 x 10 mm
Height 6 mm
Material: Stainless steel 1.4301
Surface: brushed
Length: 1,300 mm
including adhesive fixing
Space Fixing Profile - Aluminium
Space fixing profile
including spacers (12 pcs.)
Surfaces:
U 36 x 115 mm
Material:
Length:
Aluminium
3,000 mm
“Natural”
Untreated
Stainless steel
effect
(E6/EV1)
Premium
brushed stainless
steel finish
Rosette
Rosette
for M10 countersunk head screw DIN 7991
Material: Stainless steel A4
Packing unit per 12 pieces
Glass Spacer
Glass Spacer
Glass joint width:
10 mm
Material: EPDM
15 mm
Height:
36 mm
20 mm
self-adhesive on one side
Packing unit per 5 pieces for LSG Glass 2x6, 2x8 and 2x10 mm
Screw Locking
Screw Locking
50 ml bottle
2222 www.glassline.de

Applications
System Applications
www.glassline.de
23

Applications
System Application In a Flat Area
Glass and Profile
Glass
Glass
≤ 30
≤ 30
Glass width 100-6.000*
Glass width 100-6.000*
≤ 30
≤ 30
≤ 30
≤ 30
Profile
Profile length ≤ 3.000
≤ 30
37 37 mm mm
37 mm
37 mm
Glass Glass height height ≤ 1.400 ≤ 1.400 * *
Glass Glass height height ≤ 1.400 ≤ 1.400 * *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
≤ 30
≤ 30
Profile
Profile length ≤ 3.000
≤ 30
Top1 Top2 Top3 Side1 Side2
* Application and measurement tables, see pages 32-33. Profile spacing ≤ 40 mm.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
2424 www.glassline.de

Applications
System Application In a Flat Area
Corner Solution
The System
Außenecke
Außenecke
Fußboden
Outer corner
Outer corner
Applications
Floor
Wand
Wall
Innenecke
Fußboden
Glass
Inner corner
Floor
Innenecke
Inner corner
Flexible Installation of the Glass Panels
Glass independent of the profile (glass joint not on the profile joint)
≤ 30
≤ 30
Handrails
≤ 40
≤ 40
≤ 40
≤ 40
Glass conforms with the profile (glass joint on the profile joint)
≤ 30
≤ 30
≤ 40
≤ 40
≤ 40
≤ 40
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
www.glassline.de
25

Applications
System Application On Stairs
Glas und Profil
Glass
≤ 30
Glass width 100-6.000*
≤ 30
≤ 30
≤ 30
GLASS
Profile
Glass width 100-6.000*
≤ 30
Profile length ≤ 3.000
Profile length ≤ 3.000
≤ 30
≤ 30
40°
PROFILE
Top1 Top2 Top3 Side1 Side2
37 mm
37 mm
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
Glass height ≤ 1.400 *
* Application and measurement tables, see pages 32-33. Profile spacing ≤ 40 mm.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
2626 www.glassline.de

Applications
≤
System Application On Stairs
Profile Joint
The System
≤ B
≤ B
≤ B
Außenecke
Fußboden
H
≤ B
Außenecke
≥ 800
≤ 400
B
140 - 220°
50 - 90°
≤ 400
≥ 800
≤ 40°
H
H
H
50 - 130°
H
50 - 130°
B
≤ 40°
≤ B
≥ 800
≤ 400
≥ 800
B
≤ 400
B
H
140 - 220°
140 - 220°
50 - 90°
50 - 90°
≤ 400
≥ 800
≤ 400
≥ 800
≤ 40°
≤ 40°
H
H
H
H
50 - 13
Applications
50 - 130°
≤ B
≤ B
Wand
≤ B
≤ B
≤ B
H
Innenecke
H
Fußboden
≤ 90°
H
B
≥ 800
= mögliche Ausführung
≤ 400
140 - 220°
≤ 90°
50 - 90°
≤ 400
≥ 800
≤ H
H
Innenecke
H
H
H
≤ 90°
50 - 130°
≤ 90°
50 - 130°
B
B
≤ 40°
= mögliche Ausführung
B
= possible application
≤ 90°
≤ 90°
≤ H
≤ H
Glass
B
≤ 40°
≤ B
Glass independent of the profile (glass joint not on the profile joint)
H
≤ 30
≤ 90°
≤ 90°
≤ H
Handrails
B
≤ 40
≤ 40
= mögliche Ausführung
Glass conforms with the profile (glass joint on the profile joint)
≤ 30
≤ 40
≤ 40
Service
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
www.glassline.de
info
27

Applications
System Application French Balcony
With a Load-bearing Handrail Connection to the Building
≤ 30 500-6.000*
≤ 30
≤ 30 500-6.000*
≤ 30
Glass thicknesses
Private area 1 Public area 2
From 2 x 6 mm 3 From 2 x 8 mm 3
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
1
Capping load 0.5 kN/m 2 Capping load 1.0 kN/m 3 LSG made of ESG 1.52, PVB film.
info
2828 www.glassline.de

Applications
System Application French Balcony
Without a Handrail Connection to the Building
The System
≤ 30 500-6.000*
≤ 30
≤ 30 500-6.000*
≤ 30
Handrails
Glass
Applications
Glass thicknesses
Public area 2
From 2 x 10 mm 3
* Application and measurement tables, see pages 32-33.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
Service
protector profile on pages 22 + 36.
2
Capping load 1.0 kN/m 3 LSG made of TSG 1.52, PVB film.
info
www.glassline.de
29

Glass
Glass
Freedom of Design for You
Enjoy freedom with BALARDO ALU, even with the glass.
The high transparency and variety of combinations that BALARDO ALU offers
correspond with any décor, particularly in combination with the systemspecific
glass edge protector profile.
The filigree system is suitable for any individual glass design and
harmoniously supports the effect of any motif and pattern. Whether it's
printed or coloured PVB film – there is no limit to your creativity.
With BALARDO ALU you have certified type structural property tables for
all system components. We only laminated safety glass (LSG) for maximum
safety.
BALARDO ALU can be implemented as a full glass railing system without
any additional inspections. This opens up a wealth of unimaginable design
options.
Type structural properties certified by LGA
Bavaria - no additional glass type structural
properties are required for the wide range of
applications.
e.g. with a photo*
e.g. with a standard pattern*
e.g. with a company logo*
* Film printed and laminated into the laminated safety glass.
3030 www.glassline.de

Glass
Glass Composition / Application
Glass Composition
LSG-Float 1
2 x 10 mm
Das System
LSG-ESG 2
Application
2 x 6 mm 2 x 8 mm 2 x 10 mm
2
4
5
Anwendungen
1
3
1
Glass inset
2
Glass butt joint
≤ 30
3
Glass overlap
≤ 40
4
Glass gaps 3
R ≥ 15
≤ 200
≤ 500
5
Handrail/ edge
protecton
Edge protection
or joint
≤ 30 mm
Das Glas
~ 100 mm
Bottom
Top
R ≥ 15
No glass drilling
required
Handläufe
Cost-effective
Easy installation
Insert
Press
Ready!
1
Laminated safety glass comprising 2 x float glass, 1.52 mm PVB film (polyvinyl butyral film).
2
Laminated safety glass comprising 2 x toughened glass, 1.52 mm PVB film (polyvinyl butyral film).
3
Can be achieved with LSG-TSG 2 x 10 mm.
Service
Glass edges brushed or polished. Glass and profile joints should be protected against penetrating moisture. Glass dimensions, see pages 32-33
info
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge protector profile on pages 22 + 36.
www.glassline.de
31

Glass
Application and Measurement Tables
Type structural properties certified by LGA Bavaria - no additional glass type structural
properties are required for the wide range of applications.
Private Area (Capping Load 0.5 kN/m)
B
H
Glass height
Glass width
40°
B
Glass width
H
Glass height
Fixing spacing a ≤ 500 mm*
With a Handrail - Only with a Glass Edge Protector Profile
In flat areas and on stairs
Glass
Glass width
[mm]
Max. glass height
[mm]
Permissible wind load (kN/m 2 ) with a glass height
900 1,000 1,100 1,150 1,250 1,300 1,400
LSG-TSG 2 x 10 100 - 6,000 1,400 4.75 3.85 3.10 2.80 2.40 2.20 1.80
With a Load-Distributing Handrail
only in a flat area
Glass
Glass width
[mm]
Max. glass height
[mm]
Permissible wind load (kN/m 2 ) with a glass height
900 1,000 1,100 1,150 1,250 1,300 1,400
LSG Float 2 x 10 1,000 - 2,400 1 1,400 2.20 1.75 1.40 1.25 1.10 1.00 0.80
LSG-TSG 2 x 6 500 - 3,000 1 1,250 1.75 1.40 1.20 1.05 0.85
In flat areas and on stairs
Glass
Glass width
[mm]
Max. glass height
[mm]
Permissible wind load (kN/m 2 ) with a glass height
900 1,000 1,100 1,150 1,250 1,300 1,400
LSG-TSG 2 x 8 100 - 6,000 1,400 3.15 2.50 2.00 1.80 1.50 1.40 1.20
LSG-TSG 2 x 10 100 - 6,000 1,400 4.75 3.85 3.10 2.80 2.40 2.20 1.80
* Top3 fixing spacing a ≤ 200 mm
PVB film 1.52 mm
1
Handrail connection to a structure (load-bearing elements) required! Width ratio of the adjoining glass panels max. 1:2 or 2:1
Handrail joint:
750 mm from the glass joint with a non-rigid handrail connection
100 mm from the glass joint with a rigid handrail connection.
Filler and end plates 100-500 mm must be connected on the top for load distribution purposes.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
protector profile on pages 22 + 36.
info
3232 www.glassline.de

Glass
Application and Measurement Tables
Type structural properties certified by LGA Bavaria - no additional glass type structural
properties are required for the wide range of applications.
Public Area (Capping Load 1.0 kN/m)
The System
H
Glass height
B
Glass width
H
Glass height
40°
B
Glass width
Applications
Fixing spacing a ≤ 250 mm*
With a Handrail - Only with a Glass Edge Protector Profile
Glass
Glass width
[mm]
In flat areas and on stairs
Max. glass height
[mm]
Permissible wind load (kN/m 2 ) with a glass height
900 1,000 1,100 1,150 1,200 1,250 1,300
Glass
LSG-TSG 2 x 10 100 - 6,000 1,300* 4.75 3.85 3.10 2.80 2.60 2.40 2.20
With a Load-Distributing Handrail
Glass
Glass width
[mm]
In flat areas and on stairs
Max. glass height
[mm]
Permissible wind load (kN/m 2 ) with a glass height
900 1,000 1,100 1,150 1,250 1,300 1,400
LSG-TSG 2 x 8 500 - 2,400 1 1,150 3.15 2.50 2.00 1.80
LSG-TSG 2 x 10
100 - 6,000 1,300*
4.75 3.85 3.10 2.80 2.40 2.20
500 - 2,400 1 1,400* 1.80
Handrails
* Top3 glass height: max. 1,250 mm / fixing spacing a ≤ 100 mm
PVB film 1.52 mm
1
Handrail connection to a structure (load-bearing elements) required! Width ratio of the adjoining glass panels max. 1:2 or 2:1
Handrail joint: 750 mm from the glass joint with a non-rigid handrail connection
100 mm from the glass joint with a rigid handrail connection.
Filler and end plates 100-500 mm must be connected on the top for load distribution purposes.
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
info
protector profile on pages 22 + 36.
www.glassline.de
33
Service

Glass
Notes
3434 www.glassline.de

Handrails
Handrail Installation
Butt Joints & Installation
The System
Alternative 1
Possible handrail joint
≥ 750 mm away from the glass joint with
a non-rigid connection (with LSG made
of TSG 2 x 6 and 2 x 8 mm)
Applications
≤ 30
Alternative 2
Possible handrail joint
≥ 100 mm away from the
glass joint with a rigid connection
(with LSG made of
TSG 2 x 6 and 2 x 8 mm)
Glass
Handrail Installation
≤ 40
≤ 30
Handrails
≤ 40
Open and accessible glass edges need to be protected by means of constructive measures, e.g. with the glass edge
Service
protector profile on pages 22 + 36.
The handrail butt joint can be freely selected with respect to the glass edge with LSG made of TSG 2 x 10.
info
www.glassline.de
35

Handrails
Stainless Steel Handrails
System-specific glass edge protector profile
For LSG 2x10 mm
Material: Stainless steel 1.4301
Surface:
brushed
incl. adhesive fixing
Length 3,000 mm
U Profiles
30
3
27
Edge protection: U 30 x 27 x 3.0 mm
Groove dimension: 24 x 24 mm
Material: Stainless steel 1.4301
Surface:
brushed
24
incl. rubber clip-in profile
Length 3,000 mm
Round Ø 42.4 mm
Ø 42.4
1.5
24
Glass beading tube: Ø 42.4 x 1.5 mm
Groove dimension: 24 x 24 mm
Material: Stainless steel 1.4301
Surface:
brushed
24
incl. rubber clip-in profile
Length 5,000 mm
Round Ø 48.3 mm
Ø 48.3
30
24
6
1.5
Glass beading tube: Ø 48.3 x 1.5 mm
Groove dimension: 27 x 30 mm
Material: Stainless steel 1.4301
Surface:
brushed
27
incl. rubber clip-in profile
Length 5,000 mm
If necessary, adhesive should be used to secure the handrail against lifting. PVB-compatibility should be taken into consideration.
info
3636 www.glassline.de

Handrails
Wooden Handrails
U Profiles
30
3
The System
Edge protection: U 30 x 27 x 3.0 mm
Groove dimension: 24 x 24 mm
Material: Stainless steel 1.4301
Surface:
brushed
Round on a U-Profile
Applications
Wooden handrail: Ø 55 mm
Groove dimension: 31 x 30 mm
Material: Steamed beech
Surface:
polished and varnished
Glass
Rectangular on a U-Profile
Service
27
24
incl. rubber clip-in profile
Length 3,000 mm
Ø 55
30
24
for wooden add-on elements
Length 3,000 mm
31
50
Wooden handrail: w / h 50 / 40 mm
Groove dimension: 31 x 30 mm
Material: Steamed beech
Surface:
polished and varnished
40
Length 3,000 mm
30
31
Handrails
If necessary, adhesive should be used to secure the U-profile and wooden add-on element against lifting.
PVB-compatibility should be taken into consideration.
info
www.glassline.de
37

Handrails
Customised Handrail
Sample Applications
* Load-bearing handrail
Glass joint 21 - 26
Non-loading bearing customised handrail
≤ 500
≥ 50
Ø 52
* Load-bearing handrail
Glass joint 21 - 26
≤ 500
≥ 50
Ø 52
Non-loading bearing customised handrail
* load-bearing handrail absolutely essential.
info
3838 www.glassline.de

Handrails
Customised Handrail
Curved Handrail Support
Ø 42.4
The System
80
Ø 16
Point fittings: Ø 52 mm
Material: Stainless steel 1.4404
Surface:
lathed
Straight Handrail Support
Ø 52
Ø 21
Applications
Point fittings: Ø 52 mm
Material: Stainless steel 1.4404
Surface:
lathed
Glass
Stainless Steel Handrail
Ø 42.4
2.0
Glass beading tube: Ø 42.4 x 2.0 mm
Material: Stainless steel 1.4301
Surface:
brushed
Length 3,000 mm
Handrails
Wooden Handrail
Ø 60
Service
80
55
Ø 42.4
Ø 52
Ø 21
Ø 16
Wood:
Ø 60 mm
Material: Steamed beech
Surface: polished and varnished Length 3,000 mm
www.glassline.de
39

Handrails
Accessories for Stainless Steel Handrails
Accessories for Stainless Steel Handrail Ø 42.4 mm
Handrail connector
Material:
Surface:
Stainless steel 304 V2A
brushed
Corner connector 90°
Material:
Surface:
Stainless steel 304 V2A
brushed
Handrail end caps
Material:
Surface:
Stainless steel 304 V2A
brushed
Accessories for Stainless Steel Handrail Ø 48.3 mm
Handrail connector
Material:
Surface:
Stainless steel 304 V2A
brushed
Corner connector 90°
Material:
Surface:
Stainless steel 304 V2A
brushed
Handrail end caps
Material:
Surface:
Stainless steel 304 V2A
brushed
4040 www.glassline.de

Handrails
Notes
Service
Handrails
Glass
Applications
The System
www.glassline.de
41

Service
CLICK N FIX
assembly
Installation Instructions
Installation Video
www.glassline.de/balardo
1
2
3
Fix the profile in place Insert the clamping shoe Press the outer seal firmly
4
5
6
Click
Insert the glass
Insert the clamp and press the glass
towards the outer seal
Press it until the clamp locks in place
with an audible “click”
7
8
9
Insert the inner seal
Install the handrail of the glass edge
protector profile
Ready!
4242 www.glassline.de

Service
GLAS
Enquiry Form
≤ 30
Glasbreite 100-6.000*
≤ 30
≤ 30
≤ 30
Name
Company
House Number / Street
PROFIL
Profillänge ≤ 3.000
≤ 30
Quick Enquiry:
Copy enquiry
Complete
Fax to
+49 (0) 6291/6259-11
Your enquiry will be processed as quickly
as possible.
The System
Town or City / Postcode
Tel.
E-mail
Construction projects
Fax
Applications
System Profile
Top1 Top2 Top3 Side1 Side2
metres
Glass
Glass thickness
Surface
2 x 6 mm 2 x 8 mm 2 x 10 mm
“Natural”
Untreated
Stainless steel
effect
(E6/EV1)
Premium
brushed stainless
steel finish
Accessories
Handrails
Corners Cover plate Veneering (Side1) Glass Spacer
Inner Angle Outer Angle
Facing Panel Profile Caps Glass joint 10 15 20
piece
piece
piece
piece
Handrail
Glass edge protector
profile *
Height 6 mm
U 30 x 27 mm
Ø 42.4 mm
Ø 48.3 mm
Ø 55 mm
50/40 mm
Service
*
for LSG 20
www.glassline.de
43

GLASSWALL
Ceiling-high glazing
with general technical approval (AbP)
and a safety function!
The highly transparent system makes full glass in
a railing area more attractive and cost-effective
than ever before. The innovation clamp
installation principle will win
you over and reduce installation
and planning time.
Point fixings with AbZ (general technical
approval) and type structural properties
for the problem-free planning
and implementation of point-fixed
glass constructions. For maximum
transparency and safety for a variety
of different applications.
Glassline GmbH . Industriestr. 7-8 . 74740 Adelsheim . GERMANY
Phone +49 (0) 6291 6259-0 . Fax +49 (0) 6291 6259-11
info@glassline.de . www.glassline.de
Copyright 2012 by GLASSLINE GmbH. 2nd Edition January 2013. Subject to technical changes without prior notice