GTP - 32 CONTROL PROCESSOR User Manual ... - DNF Controls
GTP - 32 CONTROL PROCESSOR User Manual ... - DNF Controls GTP - 32 CONTROL PROCESSOR User Manual ... - DNF Controls
ETHERNET LINK SPEED SETUP 1) On GTP-32 front panel, use éê keys to select “Ethernet Status”. 2) Press ENTER key. Display will show current speed selection. 3) Use éê keys to change selection. Select AUTO to use highest available speed. Select 10Mbs for long ethernet cable runs. 4) Press ENTER to save new Ethernet link speed, or press ESC to exit without saving. NOTE- New ethernet speed selection will take effect immediately. SETUP Setup is required after initial installation. Setup may also be required after changing external GPIs or GPOs. Setup is performed using a computer running an off the shelf web browser such as Internet Explorer or Firefox. Connect the CAT5 cable from the computer to the same ethernet switch that the GTP-32 is connected to. After launching the web browser, enter the IP address of the GTP-32 to be setup. The GTP-32 Home Page will be displayed. - 6 -
SET PASSWORD The default password, when shipped from the factory, is “controls”, all lower case. The password is used to access all configuration screens. Using the web browser: 1) From the GTP-32 Home Page, click on the “System” link. The System page will be displayed. 2) Click on “Set Password”. The Set Password page will be displayed. - 7 -
- Page 1 and 2: 12843 Foothill Blvd. Suite C Sylmar
- Page 3 and 4: REVISION HISTORY 2.0 First Draft of
- Page 5: CONFIGURATION Configuration is requ
- Page 9 and 10: 3) Enter any name made up of letter
- Page 11 and 12: GPI The GPI Section is responsible
- Page 13 and 14: 3) For each GPI, do the following:
- Page 15 and 16: The GPO Configuration Table will be
- Page 17 and 18: 3) For each channel, enter a channe
- Page 19 and 20: Ethernet Physical Configuration 1)
- Page 21 and 22: c. Heartbeat - Deprecated d. USP_GP
- Page 23 and 24: 4. In the Local Event Label field,
- Page 25 and 26: 1) Combinatorial Event Setup To vie
- Page 27 and 28: 5) Click on “Save and Exit” to
- Page 29 and 30: 4) A confirmation prompt will be di
- Page 31 and 32: not, an error message will be displ
- Page 33 and 34: 1) Click on the Action Definitions
- Page 35 and 36: ADD A ROW TO THE EVENT MONITORING T
- Page 37 and 38: 5) For each selected row, make the
- Page 39 and 40: 2) Delete a Backup File a. On the w
- Page 41 and 42: 4) The Current Log tag notes which
- Page 43 and 44: SPECIFICATIONS Power: 100 VAC - 240
- Page 45 and 46: GPIO CONNECTORS: GPI 1 - 16, GPI 17
- Page 47 and 48: FRONT & REAR VIEWS Front View Rear
- Page 49 and 50: GPI Jumper 1 J7 2 J8 3 J9 4 J10 5 J
- Page 51: LIMITED WARRANTY DNF Controls warra
ETHERNET LINK SPEED SETUP<br />
1) On <strong>GTP</strong>-<strong>32</strong> front panel, use éê keys to select “Ethernet<br />
Status”.<br />
2) Press ENTER key. Display will show current speed selection.<br />
3) Use éê keys to change selection.<br />
Select AUTO to use highest available speed.<br />
Select 10Mbs for long ethernet cable runs.<br />
4) Press ENTER to save new Ethernet link speed, or press ESC to<br />
exit without saving.<br />
NOTE- New ethernet speed selection will take effect immediately.<br />
SETUP<br />
Setup is required after initial installation. Setup may also be required after<br />
changing external GPIs or GPOs.<br />
Setup is performed using a computer running an off the shelf web browser<br />
such as Internet Explorer or Firefox. Connect the CAT5 cable from the<br />
computer to the same ethernet switch that the <strong>GTP</strong>-<strong>32</strong> is connected to.<br />
After launching the web browser, enter the IP address of the <strong>GTP</strong>-<strong>32</strong> to be<br />
setup. The <strong>GTP</strong>-<strong>32</strong> Home Page will be displayed.<br />
- 6 -
Change language