GTP - 32 CONTROL PROCESSOR User Manual ... - DNF Controls

More documents

Recommendations

Info

If prompted for password, enter your password then click on “Login” to log in to the GTP-32. If already logged in, the password prompt will not be displayed. The GPI Configuration Table will be displayed with drop down boxes. - 12 -
3) For each GPI, do the following: Note: It is only necessary to change these settings to achieve specific functions. Under normal use these will remain at their default settings. Enter a label name to help identify the GPI with a source function. Set the “User Define ON State”. Click on the drop down arrow. Select OPTO ON if the GPI is considered “ON” when power (+V or –V) is applied across the GTP-32’s optoisolator 2-wire input. Select OPTO OFF if the GPI is considered on when no power is applied across the GTP-32’s opto-isolator 2- wire input. Set the “User Defined ON Mode”. Click on the drop down arrow. Select LATCHED if the GPI source signal turns on and stays on when activated. The GPI source signal turns off and stays off when de-activated (GPI follows the source signal). This is the recommended setting. Select MOMENTARY if the GPI source signal turns on for a specific duration then automatically turns off, when activated. If MOMENTARY is selected, enter a “Debounce” time in the DEBOUNCE box. If LATCH was selected, debounce time is ignored. The debounce time is used to filter out unwanted GPI signals. If the debounce time is greater than that GPI’s on time, then the GPI will be ignored. If the debounce time is less that the GPI on time, then the GPI will be detected. Set the debounce time to the minimum on time of the GPI to be detected. All debounce time entries are automatically multiplied by 10milliseconds. The minimum entry is “1”, for 10 milliseconds. The maximum entry is “255” for 2550 milliseconds. All entries greater than “255” will be set to “255”. 4) After entering GPI configuration data, click on SAVE to save the entered configuration data or click on CANCEL to exit without saving. - 13 -
Page 1 and 2: 12843 Foothill Blvd. Suite C Sylmar
Page 3 and 4: REVISION HISTORY 2.0 First Draft of
Page 5 and 6: CONFIGURATION Configuration is requ
Page 7 and 8: SET PASSWORD The default password,
Page 9 and 10: 3) Enter any name made up of letter
Page 11: GPI The GPI Section is responsible
Page 15 and 16: The GPO Configuration Table will be
Page 17 and 18: 3) For each channel, enter a channe
Page 19 and 20: Ethernet Physical Configuration 1)
Page 21 and 22: c. Heartbeat - Deprecated d. USP_GP
Page 23 and 24: 4. In the Local Event Label field,
Page 25 and 26: 1) Combinatorial Event Setup To vie
Page 27 and 28: 5) Click on “Save and Exit” to
Page 29 and 30: 4) A confirmation prompt will be di
Page 31 and 32: not, an error message will be displ
Page 33 and 34: 1) Click on the Action Definitions
Page 35 and 36: ADD A ROW TO THE EVENT MONITORING T
Page 37 and 38: 5) For each selected row, make the
Page 39 and 40: 2) Delete a Backup File a. On the w
Page 41 and 42: 4) The Current Log tag notes which
Page 43 and 44: SPECIFICATIONS Power: 100 VAC - 240
Page 45 and 46: GPIO CONNECTORS: GPI 1 - 16, GPI 17
Page 47 and 48: FRONT & REAR VIEWS Front View Rear
Page 49 and 50: GPI Jumper 1 J7 2 J8 3 J9 4 J10 5 J
Page 51: LIMITED WARRANTY DNF Controls warra

GTP - 32 CONTROL PROCESSOR User Manual ... - DNF Controls

Create successful ePaper yourself

Delete template?

Save as template?