Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema
Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema
Wisotronic dialog 1-Channel Central Control Unit EWFS ® The wind alert remains active for a specific period for safety and comfort reasons. 7.3.4 Wind monitoring „OFF“ delay This smoothens the move behavior of your sunblind because the sunblind is not moved for the duration of the OFF delay, but remains in the "UP" position. After the OFF delay period has expired, the sunblind can be moved again by means of comfort functions or manual operation. The setting range is from 0 - 99 minutes. Proceed as follows in order to change the OFF delay period: ■ Change to the wind monitoring menu as described above. The following display is shown: Wind monitoring ON — + | } ■ Turn the function dial until the following display appears: Wind delay OFF 10 minutes — + | } ■ Change the settings by using the buttons — + and then press the button |(save) If you want to exit the menu without saving the changes, press the }button twice consecutively. This completes the process. 90 We reserve the right to carry out improvements 932806A0•816757•7974k0•08.10.2004
Wisotronic dialog 1-Channel Central Control Unit EWFS ® The ice monitoring function ensures that your sunblind does not freeze solid while 7.4 Ice monitoring in the down position and can be damaged later by move commands. The Wisotronic therefore moves the sunblind up in case of cold weather in connection with rain before ice can form in the guide rails. Note: The ice monitoring function is de-activated in our works. During an ice alert both manual control and comfort control operation are blocked. Prerequisite for ice monitoring: A sensor for external temperature and a "Rain" sensor have to be connected. If the external temperature drops below an adjustable value and the "Rain" sensor signals precipitation, the sunblind is moved up and blocked up in the upper end position. The following values can be changed for each channel: Ice monitoring ON/OFF ON/OFF Ice monitoring Ice limit UP Ice alert autom. reset +2... +9°C ON/OFF Fig. 7-10: Ice monitoring: Values which can be changed. 7.4.1 Ice monitoring ON/OFF Proceed as follows to activate or de-activate the ice monitoring: ■ Change to the service settings menu as described above. The following display is shown: Product { } ■ Turn the function dial until the following display appears: Ice monitoring { } ■ Select this menu item (button {). The following display appears: Ice monitoring ON — + | } ■ Change the settings by using the buttons — + and then press the button | (save) If you want to exit the menu without saving the changes, press the }button twice consecutively. This completes the process. 932806A0•816757•7974k0•08.10.2004 We reserve the right to carry out improvements 91
- Page 39 and 40: Wisotronic dialog 1-Channel Central
- Page 41 and 42: Wisotronic dialog 1-Channel Central
- Page 43 and 44: Wisotronic dialog 1-Channel Central
- Page 45 and 46: Wisotronic dialog 1-Channel Central
- Page 47 and 48: Wisotronic dialog 1-Channel Central
- Page 49 and 50: Wisotronic dialog 1-Channel Central
- Page 51 and 52: Wisotronic dialog 1-Channel Central
- Page 53 and 54: Wisotronic dialog 1-Channel Central
- Page 55 and 56: Wisotronic dialog 1-Channel Central
- Page 57 and 58: Wisotronic dialog 1-Channel Central
- Page 59 and 60: Wisotronic dialog 1-Channel Central
- Page 61 and 62: Wisotronic dialog 1-Channel Central
- Page 63 and 64: Wisotronic dialog 1-Channel Central
- Page 65 and 66: Wisotronic dialog 1-Channel Central
- Page 67 and 68: Wisotronic dialog 1-Channel Central
- Page 69 and 70: Wisotronic dialog 1-Channel Central
- Page 71 and 72: Wisotronic dialog 1-Channel Central
- Page 73 and 74: Wisotronic dialog 1-Channel Central
- Page 75 and 76: Wisotronic dialog 1-Channel Central
- Page 77 and 78: Wisotronic dialog 1-Channel Central
- Page 79 and 80: Wisotronic dialog 1-Channel Central
- Page 81 and 82: Wisotronic dialog 1-Channel Central
- Page 83 and 84: Wisotronic dialog 1-Channel Central
- Page 85 and 86: Wisotronic dialog 1-Channel Central
- Page 87 and 88: Wisotronic dialog 1-Channel Central
- Page 89: Wisotronic dialog 1-Channel Central
- Page 93 and 94: Wisotronic dialog 1-Channel Central
- Page 95 and 96: Wisotronic dialog 1-Channel Central
- Page 97 and 98: Wisotronic dialog 1-Channel Central
- Page 99 and 100: Wisotronic dialog 1-Channel Central
- Page 101 and 102: Wisotronic dialog 1-Channel Central
- Page 103: Wisotronic dialog 1-Channel Central
<strong>Wisotronic</strong> <strong>dialog</strong> 1-<strong>Channel</strong> <strong>Central</strong><br />
<strong>Control</strong> <strong>Unit</strong> <strong>EWFS</strong> ® The ice monitoring function ensures that your sunblind does not freeze solid while<br />
7.4 Ice monitoring<br />
in the down position and can be damaged later by move commands. The<br />
<strong>Wisotronic</strong> therefore moves the sunblind up in case of cold weather in connection<br />
with rain before ice can form in the guide rails. Note: The ice monitoring function<br />
is de-activated in our works. During an ice alert both manual control and comfort<br />
control operation are blocked. Prerequisite for ice monitoring: A sensor for<br />
external temperature and a "Rain" sensor have to be connected. If the external<br />
temperature drops below an adjustable value and the "Rain" sensor signals<br />
precipitation, the sunblind is moved up and blocked up in the upper end position.<br />
The following values can be changed for each channel:<br />
Ice monitoring ON/OFF<br />
ON/OFF<br />
Ice<br />
monitoring<br />
Ice limit UP<br />
Ice alert<br />
autom. reset<br />
+2...<br />
+9°C<br />
ON/OFF<br />
Fig. 7-10:<br />
Ice monitoring: Values which can be changed.<br />
7.4.1 Ice monitoring ON/OFF<br />
Proceed as follows to activate or de-activate the ice monitoring:<br />
■ Change to the service settings menu as described above. The following<br />
display is shown:<br />
Product<br />
{ }<br />
■<br />
Turn the function dial until the following display appears:<br />
Ice<br />
monitoring<br />
{ }<br />
■<br />
Select this menu item (button {). The following display appears:<br />
Ice<br />
monitoring<br />
ON<br />
— + | }<br />
■ Change the settings by using the buttons — + and then press the button |<br />
(save) If you want to exit the menu without saving the changes, press the<br />
}button twice consecutively. This completes the process.<br />
932806A0•816757•7974k0•08.10.2004 We reserve the right to carry out improvements 91