Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

More documents

Recommendations

Info

Wisotronic dialog 1-Channel Central Control Unit EWFS ® Strong wind can cause considerable damage to the sun protection. The 7.3 Wind Monitoring Wisotronic therefore includes a permanent wind monitoring function which protects your sun protection against storm damage. In case of a wind alert the sun protection is moved up automatically and cannot be moved either manually or by a comfort function. The limits for a wind alert are already stored productspecifically in the Wisotronic. However, they can be changed and saved afterwards. Please ensure that you have already set the connected sun protection products correctly as described above. This means that usable setting values have already been stored for each sun protection product. The following values can be changed for each channel: Wind monitoring ON/OFF ON/OFF Wind monitoring Wind limit UP Wind delay UP Wind delay OFF 0...20 m/s 0...20 Sek 0...99 Minutes Fig. 7-8: Wind monitoring: Values which can be changed. 86 We reserve the right to carry out improvements 932806A0•816757•7974k0•08.10.2004
Wisotronic dialog 1-Channel Central Control Unit EWFS ® Fig. 7-9: 1 2 3 4 5 6 Wind speed (m/s) Adjusted limit UP Coarse of wind speed Delay UP Delay UP Delay OFF < 5 Sec = 5 Sec = 2 Min Time Wind speed and move behavior The thick black curve represents the course of the wind speed. The horizontal line represents the limit set by you for moving the sun protection up. The vertical dashed lines mark the delay periods for activating and de-activating. Let us assume that you have set 5 seconds for the activation delay period and 2 minutes for de-activation delay period, then the sun protection reacts as follows: The wind speed increases until Point 1 of the curve is reached. The limit for moving the sun protection up is reached here. The "UP" delay period now begins to run so that your sun protection is not yet moved up. At Point 2 of the curve the speed drops below the limit for moving up. The delay period is now canceled before it has expired and your sun protection has remained below. Later on the wind speed increases again and exceeds the limit once more at Point 3. The "UP" delay period now begins to run again so that your sun protection is not yet moved up. However, the delay period has already expired at Point 4 and the limit is still exceeded - the sun protection now moves up. The wind now drops again and its speed drops below the "Up" limit at Point 5. Nothing happens yet, because the de-activation delay period now first starts - the sun protection therefore does not travel down yet. At Point 6 the de-activation delay period has finally expired and the speed still lies below the limit. The wind monitoring function now enables the operation of the sun protection again. The correct setting of the delay periods thus results in a comfortable control of the sun protection. It contributes to "smoothening" the reaction behavior of the control system. This ensures that the sun protection is not moved immediately whenever the wind speed changes. 932806A0•816757•7974k0•08.10.2004 We reserve the right to carry out improvements 87
Page 1 and 2:
WAREMA Controls Wisotronic dialog 1
Page 3 and 4:
Table of contents 1. General ......
Page 5 and 6:
Table of contents 7. Service settin
Page 7 and 8:
Wisotronic dialog 1-Channel Central
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36: Wisotronic dialog 1-Channel Central
Page 85: Wisotronic dialog 1-Channel Central
Page 103: Wisotronic dialog 1-Channel Central
show all

Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?