Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

More documents

Recommendations

Info

Wisotronic dialog 1-Channel Central Control Unit EWFS ® 6.1.7 Sun control limit "OPEN" This function only makes sense if you have selected a slat product (external venetian blind or internal venetian blind) as the product type. This specifies the brightness from which the slats of external or internal venetian blinds are to be turned to a horizontal position, for example in order to let more light into the room when the sky is covered but bright. The setting range is from 0 - 99 klx. If you do not want to evaluate the limit "OPEN", you can also set the value "0" (---) here. Proceed as follows in order to change the setting value: ■ Change to the sun control menu as described above. Turn the function dial until the following display appears: Sun limit OPEN 28 klx — + | } ■ Change the setting values by using the buttons — + and then press the button | (save). If you want to exit the menu without saving the changes, press the } button twice consecutively. This completes the process. 6.1.8 Sun control delay "OPEN" This function only makes sense if you have selected a slat product (external venetian blind or internal venetian blind) as the product type. A delay period can be assigned to the "OPEN" limit so that the slats are not turned open immediately whenever the intensity of brightness changes (for example if the clouds only become denser temporarily). This smooths the movement behavior of the sun protection and thus increases the comfort. The turn command is triggered and the slats are turned open if the limits are reached or if the value drops below these limits for the duration of the delay period. The setting range is from 0 - 99 minutes. Proceed as follows in order to change the setting value: ■ Change to the sun control menu as described above. Turn the function dial until the following display appears: Sun delay OPEN 0 minutes — + | } ■ Change the setting values by using the buttons — + and then press the button | (save). If you want to exit the menu without saving the changes, press the } button twice consecutively. This completes the process. 6.1.8.1 The "OPEN" limit The following instructions for the setting of the "DOWN", "OPEN" and "UP" limits have to be observed in order for the sun control to function properly in connection with the "OPEN" limit: ■ ■ ■ The lowest value must always be the value for "UP", for example 5 klx The highest value must always be the value for "DOWN", for example 30 klx The value for "OPEN" must be set between these values, for example 10 klx. TIP In order to find the optimal setting for your sun protection system you should test various values on a bright day with varying cloud situations. This is the only way of obtaining the optimum result. 28 We reserve the right to carry out improvements 932806A0•816757•7974k0•08.10.2004
Wisotronic dialog 1-Channel Central Control Unit EWFS ® This function only makes sense if you have selected a slat product (external 6.1.9 Slat angle after moving down venetian blind or internal venetian blind) as the product type. If you have connected slat products such as external venetian blinds, you can specify how the slats are to be set after the movement down has been completed. This makes sense in particular if you prefer a particular setting. In addition, you do not have to turn the slats open manually after an automatic movement down. The sun control takes over the task of turning open the slats for you automatically if a corresponding programming exists. The slat setting for automatic operation has been set to a value of 38° in our works. The following figure illustrates the setting of the slat angle: Positive value: Slats are turned outwards Negative value: Slats are turned inwards Setting 0°: The slats remain in a horizontal position Outside Inside +80° 0° -80° Fig. 6-3: TIP Slat angle of external venetian blinds and internal venetian blinds The product-typical turning time as well as the producttypical turning angle (refer to Section 7.2.3 to 7.2.5) have to be set first. Note: The setting range of the slat angle depends on the settings made in Section 7.2.3 to 7.2.5. Proceed as follows in order to change the setting value: ■ Change to the sun control menu as described above. Turn the function dial until the following display appears: Sun angle DOWN 38° — + | } ■ Change the setting values by using the buttons — + and then press the button | (save). If you want to exit the menu without saving the changes, press the ¡ button twice consecutively. This completes the process. 932806A0•816757•7974k0•08.10.2004 We reserve the right to carry out improvements 29
Page 1 and 2: WAREMA Controls Wisotronic dialog 1
Page 3 and 4: Table of contents 1. General ......
Page 5 and 6: Table of contents 7. Service settin
Page 7 and 8: Wisotronic dialog 1-Channel Central
Page 27: Wisotronic dialog 1-Channel Central
Page 79 and 80:
Wisotronic dialog 1-Channel Central
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103:
show all

Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?