Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

More documents

Recommendations

Info

Wisotronic dialog 1-Channel Central Control Unit EWFS ® 11. Cleaning Clean the device occasionally with a moist soft cloth. Vapor or high-pressure cleaning equipment, scouring sponges, scouring agents, solvents such as alcohol or naphtha may not be used! CAUTION If cleaning at the sun protection central unit, at the sun protection itself or immediately next to the sun protection is necessary, de-energize the system beforehand and secure it against being activated again. 12. Disposal The device has to be disposed of or recycled in accordance with the statutory regulations. 13. User Information for use in: A, B, D, DK, E, F, FIN, GB, GR, I, IRL, L, NL, P, S, CH, IS, N. Receiver for sunblind remote control. The device complies at intended use with the essential requirements, which are fixed in the following EC-Guidelines and harmonized standards: - Directive on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity 1999/5/EC(R&TTE) - Directive on electromagnetic compability 89/336/EEC - Low voltage directive 73/23/EWG Link to declaration of conformity: http://www.warema.de 100 We reserve the right to carry out improvements 932806A0•816757•7974k0•08.10.2004
Wisotronic dialog 1-Channel Central Control Unit EWFS ® 14. Trouble shooting Wisotronic dialog 1-Channel control unit EWFS Remedy Type of Fault Possible cause Elimination of faults No Display Fuse has triggered No supply voltage Contact specialist dealer Switch on supply voltage Move command of remote control is Remote control was not learned Learn remote control not executed At 8-channel remote control: Incorrect channel has been selected Select correct channel, then repeat move command Button was pressed too briefly Repeat move command, keep button pressed a bit longer Interfering ambient influences Reduce distance to Wisotronic Move commands of the remote control are only carried out sporadically Safety function: Wind, Ice or rain alert active, wind sensor test has recognized error Interfering ambient influences Interference through other transmitter Batteries in the remote control are weak Wait until wind, rain alert no longer exists, reset ice alert, reset wind sensor test Reduce distance to Wisotronic Switch off other transmitter (e.g. baby intercom) Replace both batteries by new ones Sunblind can not be operated manually Safety function: Wind, ice or rain alert active, wind sensor test has recognized error Wait until wind, rain alert no longer exists, reset ice alert, reset wind sensor test Wind alert is triggered even wind is weak Wind alert is not triggered even wind is strong Rain alert not triggered Wind limit set too low Wind limit set too high Wind monitoring de-activated "Rain" sensor not connected, defective or soiled Rain monitoring function de-activated Increase wind limit, observe safety instructions Decrease wind limit, observe safety instructions Activate wind monitoring Check, clean sensor Activate function Ice alert not triggered Ice monitoring function de-activated Activate ice monitoring function Comfort functions Dawn/dusk, Sun or Temperature control do not function as required Sunblind moves down too late at sunshine Temperature limit set too low "Rain" sensor not connected, defective or soiled Comfort timer has not enabled the comfort functions Time and date settings not correct Sun control limit DOWN set too high Delay DOWN set too long Increase limit, observe safety instructions Check, clean sensor Modify the programming of the comfort timer Set the current time and date Decrease limit Decrease limit Sunblind already moves down at low Sun control limit DOWN set too low Increase limit sun irradiation Sunblind moves up too late at cloud Sun control limit UP set too low Increase limit Sunblind does not move as a function of the sun irradication Sun control de-activated Delay UP set too long Activate sun control Decrease limit Sunblind does not move at dawn/dusk Dawn/dusk control de-activated Activate dawn/dusk control Limits of dawn/dusk control not programmed correctly "Photo" sensor not mounted correctly Change limits Check mounting site 932806A0•816757•7974k0•08.10.2004 We reserve the right to carry out improvements 101
Page 1 and 2:
WAREMA Controls Wisotronic dialog 1
Page 3 and 4:
Table of contents 1. General ......
Page 5 and 6:
Table of contents 7. Service settin
Page 7 and 8:
Wisotronic dialog 1-Channel Central
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50: Wisotronic dialog 1-Channel Central
Page 99: Wisotronic dialog 1-Channel Central
Page 103: Wisotronic dialog 1-Channel Central
show all

Wisotronic dialog 1-Channel Central Control Unit EWFS - Warema

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?