EFIS-D100 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

DSAB Configuration Initial Setup As mentioned at the beginning of this chapter, configure your DSAB network only after all other installation steps have been performed, including updating all products to the latest version of firmware available from the Dynon Avionics web site at downloads.dynonavionics.com. To begin configuration, enter the EFIS > SETUP > DSAB menu. A full-page menu appears with three options: STATUS, CONFIGURATION, and BRIGHTNESS. Push DOWN▼ to select CONFIGURATION and then SEL► to enter the CONFIGURATION submenu. Note that if you press CONFIGURATION from an EMS-only product (via EMS > SETUP > DSAB), the display prompts you to begin the configuration process from an EFIS-based product. If this is not your first time configuring your DSAB network, a prompt appears asking if you wish to re-configure the network. If you do not want to re-configure, press NO; otherwise, press YES to proceed with configuration as if this is a first-time install. The first screen in the configuration process asks you to power on all devices in the system before pressing CONFIGURE NOW (button 1 or 2). After doing this, a second screen appears asking you to wait while the instrument detects all other devices connected via DSAB. While doing this, it assigns both the Bus Master and EFIS roles to itself. During network detection, the Bus Master attempts to automatically assign as many roles as it can. The following table describes the logic used in assigning roles for network devices. How role is assigned Bus Master Auto-assigned to instrument user is configuring on. EFIS Auto-assigned to instrument user is configuring on. If one EMS detected, assigned automatically. EMS If Bus Master is EMS (i.e., FlightDEK-D180) assigned automatically. If more than one non-bus-master EMS detected, user must assign. If one OAT detected, assigned automatically. If more than one OAT detected, user must assign. OAT Note that for an OAT to be used it must be connected to an instrument assigned the EFIS or EMS role (i.e., if configuring DSAB on a FlightDEK-D180 with no OAT attached, the OAT role cannot be assigned to another instrument in the system as the FlightDEK-D180 is already assigned both the EFIS and EMS roles). Compass Auto-assigned to instrument providing the EFIS/Bus Master roles. AP CTRL PANEL HS34 If one AP74 detected, assigned automatically. If more than one AP74 detected, error displayed: Not a supported configuration. If one HS34 detected, assigned automatically. If more than one HS34 detected, error displayed: Not a supported configuration. 5-4 EFIS-D100 Installation Guide
AP ROLL/PITCH SERVO DSAB Configuration Roll Servo and Pitch Servo functions are automatically detected and assigned during Autopilot Servo Calibration process. See: EFIS > SETUP > AP > SERVO CALIB. More than two SV32s or SV42s is not a supported configuration. If the configuration process could not automatically assign the EMS and OAT roles (because there are 2 or more of either type found on the network), it prompts you to assign each of them to the instrument of your choice. It then presents a list of all instruments on the network capable of being assigned each role. Use the DOWN▼ and UP▲ buttons to select the preferred instrument to provide the given role. The serial number for each unit is displayed next to its product type. Additionally, with an instrument type selected, pressing IDENT changes that instrument’s display to a black screen with the text DSAB IDENT shown. If the instrument you wish to identify is the one which you are currently interacting with, the line changes to read THIS UNIT. When you have selected the preferred provider for the role, press SELECT to continue in the process. If necessary, repeat with the next manually assigned role. At this point, a screen is displayed, stating: (X) DEVICES FOUND NETWORK CONFIGURATION IS COMPLETE Press FINISH to end the configuration. Press UP▲ and SEL► to view the status of all connected DSAB devices. Press UP▲ or DOWN▼ to scroll through all the devices. Crosscheck the displayed devices against what you actually have installed and connected. Ensure that the STATUS for each device is listed as ACTIVE. You may repeat the configuration process as many times as you wish. Whenever you add or remove an instrument from your network, you must redo the DSAB configuration process. Note that the following DSAB configurations are not supported: More than 1 FlightDEK-D180 in the network More than 1 HS34 in the network More than 1 AP74 in the network More than 2 servos in the network Brightness Configuration In a DSAB network, changing the brightness level of one instrument affects all connected instruments. Dynon Avionics sells D100-series instruments with both regular and bright screens. Each instrument connected to your DSAB network must have its display type configured to ensure that perceived brightness matches across all screens. To do this, enter the SETUP > DSAB > BRIGHTNESS menu on each product in the system. If you purchased the bright screen option for your EFIS-D100, press TOGGLE to change the BRIGHT SCREEN status to YES. Otherwise, ensure this is set to NO. If the DIM setting of one of the screens in a DSAB network gets “out of sync” (some dim, some bright), this can be corrected by adjusting the DSAB Bus Master screen to the desired DIM and then performing a DSAB CONFIGURE. EFIS-D100 Installation Guide 5-5
Page 1: EFIS-D100 Installation Guide This p
Page 5 and 6: Table of Contents Contact Informati
Page 7 and 8: 1. INTRODUCTION This manual provide
Page 9 and 10: 2. WIRING OVERVIEW Please follow th
Page 11 and 12: Wiring Overview The pin assignments
Page 13 and 14: 3. INSTRUMENT INSTALLATION This sec
Page 15 and 16: Instrument Installation The metal s
Page 17 and 18: e accessed whenever you need to upd
Page 19 and 20: Instrument Installation (range, MPG
Page 21 and 22: Instrument Installation SERIAL ALTI
Page 23 and 24: Instrument Installation Dynon Smart
Page 25: Connecting Static & Pitot Lines The
Page 28 and 29: EFIS Calibration and Configuration
Page 30 and 31: EFIS Calibration and Configuration
Page 32 and 33: DSAB Configuration Example Networks
Page 36 and 37: DSAB Configuration Network Status T
Page 38 and 39: Autopilot Installation and Configur
Page 69 and 70: 7. APPENDIX The appendices contain
Page 71 and 72: Alert Message Description End condi
Page 73 and 74: Appendix Problem After performing a
Page 75 and 76: Appendix Appendix B: Dynon OAT Prob
Page 77 and 78: Appendix CALIBRATION AND ADJUSTMENT
Page 79 and 80: Pinouts and Function Description Ap
Page 81 and 82: Generic Device Connections Appendix
Page 83 and 84: Appendix EFIS-D100 Installation Gui
Page 85 and 86:
Appendix PANEL LOCATION AND MOUNTIN
Page 87 and 88:
Appendix HS34 CONFIGURATION This se
Page 89 and 90:
Appendix occur first in the NAV por
Page 91 and 92:
NAV and/or GPS Fail-over Appendix W
Page 93 and 94:
TOOLS AND MATERIALS REQUIRED Dynon
Page 95 and 96:
Appendix Heater Controller Wiring B
Page 97 and 98:
these lines, you may drill all the
Page 99 and 100:
Appendix flight regimes not listed
Page 101 and 102:
Appendix output, connect this to th
Page 103 and 104:
Appendix Appendix F: Replacing the
show all

EFIS-D100 Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?