EFIS-D100 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Wiring Overview WIRING SYSTEM OVERVIEW The following block diagram depicts the basic layout of the EFIS DB25 electrical connections and is for reference only. Read the specific instructions for each connection prior to installation. The colors shown refer to the Dynon-supplied EFIS harness. 2-4 EFIS-D100 Installation Guide
3. INSTRUMENT INSTALLATION This section provides you with the information needed to physically and electrically install the EFIS-D100. Selecting a Remote Compass Module Location Finding a good location for the EDC-D10A remote compass module is critical to an accurate EFIS-D100 heading display. Keep in mind that calibration can compensate for small static magnetic fields superimposed upon the earth’s field; it cannot take into account dynamic effects like AC currents, non-constant DC currents and non-stationary ferrous material (e.g., an electric turn coordinator). Use the following suggestions to help you find a good location for your EDC-D10A. Keep the EDC-D10A away from any source of magnetic fields (such as electrical equipment and currentcarrying wires) and ferrous material. Move a handheld compass throughout the space surrounding your location to get a rough idea of the suitability of your chosen location. If the needle deviates significantly from magnetic north in any given area, that location would not be ideal for the EDC-D10A. The EDC-D10A can be mounted anywhere in the aircraft (away from magnetic interference) such that its pitch is as close to that of the EFIS-D100 as possible. It does not need to be directly along any axis of the EFIS-D100. It should be mounted with the long axis parallel to the wings, the electrical connector facing toward the front of the plane, and the mounting tabs on the bottom. The bracket used to hold the EDC-D10A must hold the EDC-D10A at the same pitch, roll, and yaw as the EFIS-D100 with respect to the airframe. We recommend that you use an electronic level, if available, to make sure the EDC-D10A is aligned with the EFIS-D100 to better than 1 degree. Connector toward direction of flight Connector forward and tabs mounted down Side view of EDC-D10A, tabs mounted d own and aligned within 1 degree of pitch with EFIS-D100 EFIS-D100 Installation Guide 3-1
Page 1: EFIS-D100 Installation Guide This p
Page 5 and 6: Table of Contents Contact Informati
Page 7 and 8: 1. INTRODUCTION This manual provide
Page 9 and 10: 2. WIRING OVERVIEW Please follow th
Page 11: Wiring Overview The pin assignments
Page 15 and 16: Instrument Installation The metal s
Page 17 and 18: e accessed whenever you need to upd
Page 19 and 20: Instrument Installation (range, MPG
Page 21 and 22: Instrument Installation SERIAL ALTI
Page 23 and 24: Instrument Installation Dynon Smart
Page 25: Connecting Static & Pitot Lines The
Page 28 and 29: EFIS Calibration and Configuration
Page 30 and 31: EFIS Calibration and Configuration
Page 32 and 33: DSAB Configuration Example Networks
Page 34 and 35: DSAB Configuration Initial Setup As
Page 36 and 37: DSAB Configuration Network Status T
Page 38 and 39: Autopilot Installation and Configur
Page 62 and 63:
Autopilot Installation and Configur
Page 64 and 65:
Page 66 and 67:
Page 69 and 70:
7. APPENDIX The appendices contain
Page 71 and 72:
Alert Message Description End condi
Page 73 and 74:
Appendix Problem After performing a
Page 75 and 76:
Appendix Appendix B: Dynon OAT Prob
Page 77 and 78:
Appendix CALIBRATION AND ADJUSTMENT
Page 79 and 80:
Pinouts and Function Description Ap
Page 81 and 82:
Generic Device Connections Appendix
Page 83 and 84:
Appendix EFIS-D100 Installation Gui
Page 85 and 86:
Appendix PANEL LOCATION AND MOUNTIN
Page 87 and 88:
Appendix HS34 CONFIGURATION This se
Page 89 and 90:
Appendix occur first in the NAV por
Page 91 and 92:
NAV and/or GPS Fail-over Appendix W
Page 93 and 94:
TOOLS AND MATERIALS REQUIRED Dynon
Page 95 and 96:
Appendix Heater Controller Wiring B
Page 97 and 98:
these lines, you may drill all the
Page 99 and 100:
Appendix flight regimes not listed
Page 101 and 102:
Appendix output, connect this to th
Page 103 and 104:
Appendix Appendix F: Replacing the
show all

EFIS-D100 Installation Guide - Dynon Avionics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?