EFIS-D100 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Appendix EFIS DB25 Pin# Dynon EFIS harness color Encoder Converter Wire Color Function Blue/White (may be Green (May be Red on Serial Encoder 13 black on some older models) Transmit harnesses) 21 White Black Serial Encoder Ground STEP 3: EFIS-D100 ENCODER FORMAT For proper communication the EFIS Altitude Encoder format must be set to format number one. To change this setting, from the main menu, select: MORE > SETUP > MORE > ALTENC. Press FRMAT until it reads “1.” 7-34 EFIS-D100 Installation Guide
Appendix Appendix F: Replacing the EFIS-D100 battery pack 1. Remove the two screws (either #1 Phillips or 7/64” hex, depending on when your unit was manufactured) from the small, rectangular battery door on the side of the EFIS- D100. Remove the battery door. Do not remove any other screws from the case of the unit. 2. If you previously had a battery, disconnect it from the EFIS-D100 by unplugging the battery connector and gently pulling out old battery. It is safe to gently pull on the battery wire to remove the battery. 3. Insert the new battery with the bumpy side up. 4. Connect the battery connector to the battery. The connector is keyed; make sure it is positioned correctly. 5. Position the connector so it is centered on the end of the pack. Verify that the battery pack will not interfere with insertion of either of the door screws. 6. Reinsert screws and tighten to 12 in-lbs. Appendix G: Weights Adding any new instrument to an aircraft requires the installer to be aware of its weight and how that affects the overall weight and balance of the plane. The following are the weights of the EFIS-D100 and associated Dynon-supplied sensors. Installed EFIS-D100 .....................................................................................2 lb 13.5 oz (1.287 kg) EFIS-D100 + battery..........................................................................................3 lb 4 oz (1.465 kg) EFIS 25-pin wiring harness ................................................................................... 11.2 oz (0.32 kg) EDC-D10A ............................................................................................................3.6 oz (0.102 kg) EFIS OAT ................................................................................................................3.2 oz (0.08 kg) Heated AOA/Pitot Probe & Heater Controller ......................................................11.2 oz (0.32 kg) Unheated AOA/Pitot Probe......................................................................................5.6 oz (0.16 kg) EFIS-D100 Installation Guide 7-35
Page 1:
EFIS-D100 Installation Guide This p
Page 5 and 6:
Table of Contents Contact Informati
Page 7 and 8:
1. INTRODUCTION This manual provide
Page 9 and 10:
2. WIRING OVERVIEW Please follow th
Page 11 and 12:
Wiring Overview The pin assignments
Page 13 and 14:
3. INSTRUMENT INSTALLATION This sec
Page 15 and 16:
Instrument Installation The metal s
Page 17 and 18:
e accessed whenever you need to upd
Page 19 and 20:
Instrument Installation (range, MPG
Page 21 and 22:
Instrument Installation SERIAL ALTI
Page 23 and 24:
Instrument Installation Dynon Smart
Page 25:
Connecting Static & Pitot Lines The
Page 28 and 29:
EFIS Calibration and Configuration
Page 30 and 31:
EFIS Calibration and Configuration
Page 32 and 33:
DSAB Configuration Example Networks
Page 34 and 35:
DSAB Configuration Initial Setup As
Page 36 and 37:
DSAB Configuration Network Status T
Page 38 and 39:
Autopilot Installation and Configur
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53: Autopilot Installation and Configur
Page 69 and 70: 7. APPENDIX The appendices contain
Page 71 and 72: Alert Message Description End condi
Page 73 and 74: Appendix Problem After performing a
Page 75 and 76: Appendix Appendix B: Dynon OAT Prob
Page 77 and 78: Appendix CALIBRATION AND ADJUSTMENT
Page 79 and 80: Pinouts and Function Description Ap
Page 81 and 82: Generic Device Connections Appendix
Page 83 and 84: Appendix EFIS-D100 Installation Gui
Page 85 and 86: Appendix PANEL LOCATION AND MOUNTIN
Page 87 and 88: Appendix HS34 CONFIGURATION This se
Page 89 and 90: Appendix occur first in the NAV por
Page 91 and 92: NAV and/or GPS Fail-over Appendix W
Page 93 and 94: TOOLS AND MATERIALS REQUIRED Dynon
Page 95 and 96: Appendix Heater Controller Wiring B
Page 97 and 98: these lines, you may drill all the
Page 99 and 100: Appendix flight regimes not listed
Page 101: Appendix output, connect this to th
show all

EFIS-D100 Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?