GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 3.4.4 Sending an SMS previously stored An already written SMS can be sent from the selected storage (in the current SW version only "SM" is supported). To send the written SMS its location index is needed: • send command AT+CMSS= where: : SMS location index • wait for response: Response Reason Action +CMSS: Message has been successfully proceed ahead sent. represents the OK message reference number. ERROR some error occurred Enable the extended error codes report (see par.2.5.2.1) and retry. +CMS ERROR: 330 SMSC address unknown Insert SMSC address (see par. 3.4.1.3) +CMS ERROR: 41 "Temporary Failure", may be that the device is not registered Check for signal strength and network registration (see par. 0) on any network +CMS ERROR: 331 No network service Check for signal strength and network registration (see par. 0) +CMS ERROR: 1 Unassigned number The destination address number does not exist. Check it and repeat command. +CMS ERROR: 42 network congestion Retry later +CMS ERROR: 96 Mandatory information missing Check for destination address in the SMS, overwrite it and retry. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 74 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 For example: 1- Let's assume you want to send a SMS that was written to the storage index position number 3. We suppose you already have set up the device for text SMS mode as described on the previous paragraphs: command: AT+CMSS=3 response: +CMSS: 1 OK In this case, the SMS was successfully sent to the destination and its network message reference number is 1. 3.4.5 Sending a new SMS without storing it A new SMS can be sent directly to the network without storing it. • send command AT+CMGS="" where: : destination address • wait for prompt ">" • send SMS text (MAX 160 characters) • end command with CTRL-Z character (0x1A hexadecimal) or abort command with ESC character (0x1B hexadecimal) • wait for response: Response Reason Action +CMGS: Message has been successfully proceed ahead sent. represents the OK message reference number. ERROR some error occurred Enable the extended error codes report (see par.2.5.2.1) and retry. +CMS ERROR: 330 SMSC address unknown Insert SMSC address (see par. 3.4.1.3) +CMS ERROR: 41 "Temporary Failure", may be that the device is not registered Check for signal strength and network registration (see par. 0) on any network +CMS ERROR: 331 No network service Check for signal strength and network registration (see par. 0) +CMS ERROR: 1 Unassigned number The destination address number does not exist. Check it and repeat command. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 75 of 117
- Page 23 and 24: GE863-QUAD / PY Software User Guide
- Page 25 and 26: For example: 1 - Let's assume that
- Page 27 and 28: GE863-QUAD / PY Software User Guide
- Page 29 and 30: GE863-QUAD / PY Software User Guide
- Page 31 and 32: GE863-QUAD / PY Software User Guide
- Page 33 and 34: GE863-QUAD / PY Software User Guide
- Page 35 and 36: GE863-QUAD / PY Software User Guide
- Page 37 and 38: GE863-QUAD / PY Software User Guide
- Page 39 and 40: AT+CPBR=7 the response may look lik
- Page 41 and 42: 3.1.5 Phonebook entry Delete As fir
- Page 43 and 44: GE863-QUAD / PY Software User Guide
- Page 45 and 46: 3.2.1.1 Set the extended incoming c
- Page 47 and 48: GE863-QUAD / PY Software User Guide
- Page 49 and 50: GE863-QUAD / PY Software User Guide
- Page 51 and 52: GE863-QUAD / PY Software User Guide
- Page 53 and 54: GE863-QUAD / PY Software User Guide
- Page 55 and 56: GE863-QUAD / PY Software User Guide
- Page 57 and 58: GE863-QUAD / PY Software User Guide
- Page 59 and 60: GE863-QUAD / PY Software User Guide
- Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
- Page 63 and 64: - Data Coding Scheme - page number
- Page 65 and 66: GE863-QUAD / PY Software User Guide
- Page 67 and 68: GE863-QUAD / PY Software User Guide
- Page 69 and 70: GE863-QUAD / PY Software User Guide
- Page 71 and 72: GE863-QUAD / PY Software User Guide
- Page 73: GE863-QUAD / PY Software User Guide
- Page 77 and 78: GE863-QUAD / PY Software User Guide
- Page 79 and 80: GE863-QUAD / PY Software User Guide
- Page 81 and 82: GE863-QUAD / PY Software User Guide
- Page 83 and 84: GE863-QUAD / PY Software User Guide
- Page 85 and 86: GE863-QUAD / PY Software User Guide
- Page 87 and 88: GE863-QUAD / PY Software User Guide
- Page 89 and 90: GE863-QUAD / PY Software User Guide
- Page 91 and 92: GE863-QUAD / PY Software User Guide
- Page 93 and 94: GE863-QUAD / PY Software User Guide
- Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
- Page 97 and 98: GE863-QUAD / PY Software User Guide
- Page 99 and 100: 4.1.1 CSD application example GE863
- Page 101 and 102: GE863-QUAD / PY Software User Guide
- Page 103 and 104: GE863-QUAD / PY Software User Guide
- Page 105 and 106: GE863-QUAD / PY Software User Guide
- Page 107 and 108: GE863-QUAD / PY Software User Guide
- Page 109 and 110: GE863-QUAD / PY Software User Guide
- Page 111 and 112: MAIL FROM: GE863-QUAD / PY Softwar
- Page 113 and 114: GE863-QUAD / PY Software User Guide
- Page 115 and 116: GE863-QUAD / PY Software User Guide
- Page 117: GE863-QUAD / PY Software User Guide
<strong>GE863</strong>-<strong>QUAD</strong> / <strong>PY</strong> <strong>Software</strong> <strong>User</strong> <strong>Guide</strong><br />
1vv0300746 Rev. 1 - 23/10/06<br />
3.4.4 Sending an SMS previously stored<br />
An already written SMS can be sent from the selected storage (in the current SW version<br />
only "SM" is supported).<br />
To send the written SMS its location index is needed:<br />
• send command AT+CMSS=<br />
where:<br />
: SMS location index<br />
• wait for response:<br />
Response Reason Action<br />
+CMSS: <br />
Message has been successfully proceed ahead<br />
sent. represents the<br />
OK<br />
message reference number.<br />
ERROR some error occurred Enable the extended error<br />
codes report (see par.2.5.2.1)<br />
and retry.<br />
+CMS ERROR: 330 SMSC address unknown Insert SMSC address (see par.<br />
3.4.1.3)<br />
+CMS ERROR: 41<br />
"Temporary Failure", may be<br />
that the device is not registered<br />
Check for signal strength and<br />
network registration (see par. 0)<br />
on any network<br />
+CMS ERROR: 331 No network service Check for signal strength and<br />
network registration (see par. 0)<br />
+CMS ERROR: 1 Unassigned number The destination address<br />
number does not exist. Check it<br />
and repeat command.<br />
+CMS ERROR: 42 network congestion Retry later<br />
+CMS ERROR: 96 Mandatory information missing Check for destination address<br />
in the SMS, overwrite it and<br />
retry.<br />
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 74 of 117