GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 3.4.3 Writing a New SMS to storage A new SMS can be written in the selected storage (in the current SW version only "SM" is supported) and then can be sent to the desired destination. To write the new SMS: • send command AT+CMGW="" where: : destination address • wait for prompt ">" • send SMS text (MAX 160 characters) • end command with CTRL-Z character (0x1A hexadecimal) or abort command with ESC character (0x1B hexadecimal) • wait for response: Response Reason Action +CMGW: Message has been successfully proceed ahead written in position number OK ERROR some error occurred Enable the extended error codes report (see par.2.5.2.1) and retry. +CMS ERROR: 330 SMSC address unknown Insert SMSC address (see par. 3.4.1.3) +CMS ERROR: 322 Memory Full memory is full, hence delete some records and retry. NOTE: if command is aborted with ESC character, then only the OK result code is returned. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 72 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 For example: 1- Let's assume you want to write a new SMS to the storage and the destination address is the number +39338123456789. We suppose you already have set up the device for text SMS mode as described on the previous paragraphs: command: AT+CMGW="+39338123456789" response: > now you can insert the message text in IRA format (note that the IRA format and ASCII format coincide for the alphabet characters but not for the other). …. here will be inserted the SMS message text…. conclude text with the character CTRL-Z response: +CMGW: 3 OK In this case, the new SMS was successfully written to the location index 3 of the selected write memory (always "SM" SIM Card memory). Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 73 of 117
- Page 21 and 22: GE863-QUAD / PY Software User Guide
- Page 23 and 24: GE863-QUAD / PY Software User Guide
- Page 25 and 26: For example: 1 - Let's assume that
- Page 27 and 28: GE863-QUAD / PY Software User Guide
- Page 29 and 30: GE863-QUAD / PY Software User Guide
- Page 31 and 32: GE863-QUAD / PY Software User Guide
- Page 33 and 34: GE863-QUAD / PY Software User Guide
- Page 35 and 36: GE863-QUAD / PY Software User Guide
- Page 37 and 38: GE863-QUAD / PY Software User Guide
- Page 39 and 40: AT+CPBR=7 the response may look lik
- Page 41 and 42: 3.1.5 Phonebook entry Delete As fir
- Page 43 and 44: GE863-QUAD / PY Software User Guide
- Page 45 and 46: 3.2.1.1 Set the extended incoming c
- Page 47 and 48: GE863-QUAD / PY Software User Guide
- Page 49 and 50: GE863-QUAD / PY Software User Guide
- Page 51 and 52: GE863-QUAD / PY Software User Guide
- Page 53 and 54: GE863-QUAD / PY Software User Guide
- Page 55 and 56: GE863-QUAD / PY Software User Guide
- Page 57 and 58: GE863-QUAD / PY Software User Guide
- Page 59 and 60: GE863-QUAD / PY Software User Guide
- Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
- Page 63 and 64: - Data Coding Scheme - page number
- Page 65 and 66: GE863-QUAD / PY Software User Guide
- Page 67 and 68: GE863-QUAD / PY Software User Guide
- Page 69 and 70: GE863-QUAD / PY Software User Guide
- Page 71: GE863-QUAD / PY Software User Guide
- Page 75 and 76: GE863-QUAD / PY Software User Guide
- Page 77 and 78: GE863-QUAD / PY Software User Guide
- Page 79 and 80: GE863-QUAD / PY Software User Guide
- Page 81 and 82: GE863-QUAD / PY Software User Guide
- Page 83 and 84: GE863-QUAD / PY Software User Guide
- Page 85 and 86: GE863-QUAD / PY Software User Guide
- Page 87 and 88: GE863-QUAD / PY Software User Guide
- Page 89 and 90: GE863-QUAD / PY Software User Guide
- Page 91 and 92: GE863-QUAD / PY Software User Guide
- Page 93 and 94: GE863-QUAD / PY Software User Guide
- Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
- Page 97 and 98: GE863-QUAD / PY Software User Guide
- Page 99 and 100: 4.1.1 CSD application example GE863
- Page 101 and 102: GE863-QUAD / PY Software User Guide
- Page 103 and 104: GE863-QUAD / PY Software User Guide
- Page 105 and 106: GE863-QUAD / PY Software User Guide
- Page 107 and 108: GE863-QUAD / PY Software User Guide
- Page 109 and 110: GE863-QUAD / PY Software User Guide
- Page 111 and 112: MAIL FROM: GE863-QUAD / PY Softwar
- Page 113 and 114: GE863-QUAD / PY Software User Guide
- Page 115 and 116: GE863-QUAD / PY Software User Guide
- Page 117: GE863-QUAD / PY Software User Guide
<strong>GE863</strong>-<strong>QUAD</strong> / <strong>PY</strong> <strong>Software</strong> <strong>User</strong> <strong>Guide</strong><br />
1vv0300746 Rev. 1 - 23/10/06<br />
3.4.3 Writing a New SMS to storage<br />
A new SMS can be written in the selected storage (in the current SW version only "SM" is<br />
supported) and then can be sent to the desired destination.<br />
To write the new SMS:<br />
• send command AT+CMGW=""<br />
where:<br />
: destination address<br />
• wait for prompt ">"<br />
• send SMS text (MAX 160 characters)<br />
• end command with CTRL-Z character (0x1A hexadecimal) or abort command with ESC character<br />
(0x1B hexadecimal)<br />
• wait for response:<br />
Response Reason Action<br />
+CMGW: <br />
Message has been successfully proceed ahead<br />
written in position number<br />
OK<br />
<br />
ERROR some error occurred Enable the extended error<br />
codes report (see par.2.5.2.1)<br />
and retry.<br />
+CMS ERROR: 330 SMSC address unknown Insert SMSC address (see par.<br />
3.4.1.3)<br />
+CMS ERROR: 322 Memory Full memory is full, hence delete<br />
some records and retry.<br />
NOTE: if command is aborted with ESC character, then only the OK result code is returned.<br />
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 72 of 117