GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 3.2.2.1 Set Caller line ID indication presentation • Send command AT+CLIP= where: is the operation mode selected: 0 – Calling Line Indication Presentation Disabled 1 – Calling Line Indication Presentation Enabled • wait for OK response For example: 1- Let's assume you receive a call from the national number 1234567890 and extended incoming calls indication is disabled while CLIP is enabled, you'll see: ring indication: RING +CLIP: "1234567890",129 2- Let's assume you receive a call from the international number +391234567890 and extended incoming calls indication is disabled while CLIP is enabled, you'll see: ring indication: RING +CLIP: "+391234567890",145 NOTE: this does not mean that the incoming call is an international one, it simply means that the numbering scheme used to identify the caller is the international one. 3.2.3 Restricting Calling Line Indication The GE863-QUAD / PY is able to send the calling line indication (CLI) to the other party through the network when an outgoing call is made. This indication can be restricted (CLIR) in various ways: • CLI sent always • CLI never sent • CLI temporary sent (normally not sent) • CLI temporary not sent (normally sent) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 46 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 3.2.3.1 CLIR Service status query • send command AT+CLIR • wait for response in the format: +CLIR: , OK where: is the facility status on the Mobile 0 – CLIR facility according to CLIR service network status 1 – CLIR facility active (CLI not sent) 2 – CLIR facility not active (CLI sent) is the facility status on the Network 0 - CLIR service not provisioned (service unavailable) 1 - CLIR service provisioned (service available) 2 - unknown (e.g. no network present, etc.) 3 - CLI temporary mode presentation restricted 4 - CLI temporary mode presentation allowed NOTE: The parameter reports the status of the service at network level. If the CLIR service is not provisioned, then it is not possible to use this service and changing the first parameter will not change the CLI presentation to the other party behavior of the network. For example: 1- Let's assume you want to check your CLIR settings: command: AT+CLIR response: +CLIR: 2,4 In this case the CLIR service is temporary mode allowed on the network and the mobile sends the CLI when calling. (CLI Restriction not active). Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 47 of 117
- Page 1 and 2: GE863-QUAD / PY Software User Guide
- Page 3 and 4: GE863-QUAD / PY Software User Guide
- Page 5 and 6: GE863-QUAD / PY Software User Guide
- Page 7 and 8: GE863-QUAD / PY Software User Guide
- Page 9 and 10: GE863-QUAD / PY Software User Guide
- Page 11 and 12: GE863-QUAD / PY Software User Guide
- Page 13 and 14: GE863-QUAD / PY Software User Guide
- Page 15 and 16: GE863-QUAD / PY Software User Guide
- Page 17 and 18: 2.5.2.3 Provide SIM PIN (only if re
- Page 19 and 20: GE863-QUAD / PY Software User Guide
- Page 21 and 22: GE863-QUAD / PY Software User Guide
- Page 23 and 24: GE863-QUAD / PY Software User Guide
- Page 25 and 26: For example: 1 - Let's assume that
- Page 27 and 28: GE863-QUAD / PY Software User Guide
- Page 29 and 30: GE863-QUAD / PY Software User Guide
- Page 31 and 32: GE863-QUAD / PY Software User Guide
- Page 33 and 34: GE863-QUAD / PY Software User Guide
- Page 35 and 36: GE863-QUAD / PY Software User Guide
- Page 37 and 38: GE863-QUAD / PY Software User Guide
- Page 39 and 40: AT+CPBR=7 the response may look lik
- Page 41 and 42: 3.1.5 Phonebook entry Delete As fir
- Page 43 and 44: GE863-QUAD / PY Software User Guide
- Page 45: 3.2.1.1 Set the extended incoming c
- Page 49 and 50: GE863-QUAD / PY Software User Guide
- Page 51 and 52: GE863-QUAD / PY Software User Guide
- Page 53 and 54: GE863-QUAD / PY Software User Guide
- Page 55 and 56: GE863-QUAD / PY Software User Guide
- Page 57 and 58: GE863-QUAD / PY Software User Guide
- Page 59 and 60: GE863-QUAD / PY Software User Guide
- Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
- Page 63 and 64: - Data Coding Scheme - page number
- Page 65 and 66: GE863-QUAD / PY Software User Guide
- Page 67 and 68: GE863-QUAD / PY Software User Guide
- Page 69 and 70: GE863-QUAD / PY Software User Guide
- Page 71 and 72: GE863-QUAD / PY Software User Guide
- Page 73 and 74: GE863-QUAD / PY Software User Guide
- Page 75 and 76: GE863-QUAD / PY Software User Guide
- Page 77 and 78: GE863-QUAD / PY Software User Guide
- Page 79 and 80: GE863-QUAD / PY Software User Guide
- Page 81 and 82: GE863-QUAD / PY Software User Guide
- Page 83 and 84: GE863-QUAD / PY Software User Guide
- Page 85 and 86: GE863-QUAD / PY Software User Guide
- Page 87 and 88: GE863-QUAD / PY Software User Guide
- Page 89 and 90: GE863-QUAD / PY Software User Guide
- Page 91 and 92: GE863-QUAD / PY Software User Guide
- Page 93 and 94: GE863-QUAD / PY Software User Guide
- Page 95 and 96: esponse: +CCLK="02/11/07,13:24:47"
<strong>GE863</strong>-<strong>QUAD</strong> / <strong>PY</strong> <strong>Software</strong> <strong>User</strong> <strong>Guide</strong><br />
1vv0300746 Rev. 1 - 23/10/06<br />
3.2.3.1 CLIR Service status query<br />
• send command AT+CLIR<br />
• wait for response in the format:<br />
+CLIR: ,<br />
OK<br />
where:<br />
is the facility status on the Mobile<br />
0 – CLIR facility according to CLIR service network status<br />
1 – CLIR facility active (CLI not sent)<br />
2 – CLIR facility not active (CLI sent)<br />
is the facility status on the Network<br />
0 - CLIR service not provisioned (service unavailable)<br />
1 - CLIR service provisioned (service available)<br />
2 - unknown (e.g. no network present, etc.)<br />
3 - CLI temporary mode presentation restricted<br />
4 - CLI temporary mode presentation allowed<br />
NOTE: The parameter reports the status of the service at network level.<br />
If the CLIR service is not provisioned, then it is not possible to use this service and changing<br />
the first parameter will not change the CLI presentation to the other party behavior of the<br />
network.<br />
For example:<br />
1- Let's assume you want to check your CLIR settings:<br />
command:<br />
AT+CLIR <br />
response:<br />
+CLIR: 2,4<br />
In this case the CLIR service is temporary mode allowed on the network and the mobile sends the CLI<br />
when calling. (CLI Restriction not active).<br />
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 47 of 117