GE863-QUAD / PY Software User Guide
GE863-QUAD / PY Software User Guide GE863-QUAD / PY Software User Guide
For example: 1- Let's assume you have to call the national number 040 - 4192111, command: ATD 0404192111 response CONNECT 9600 GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 2- Let's assume you have to call the national number but in international format +39-40-4192111, command: ATD +39404192111 response CONNECT 9600 3- Let's assume you have to call the international number +386-40-4192111, command: ATD +386404192111 response CONNECT 9600 2.7.3 Closing the Data call 2.7.3.1 Exit the data mode and enter the command mode • Send escape sequence +++ • wait the escape sequence pause time ( see S12 parameter) • wait for response OK NOTE: After the Escape sequence and during the call the only command that is accepted by the GE863-QUAD / PY is the ATH. All the other commands are not supported during a call. TIP: during the escape sequence pause time S12 no further characters should be sent to the device in order to enter the command mode. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 30 of 117
GE863-QUAD / PY Software User Guide 1vv0300746 Rev. 1 - 23/10/06 2.7.3.2 Hang up the data call • Send command ATH • wait for response NO CARRIER TIP: during the data call the device remains in data (on line) mode, so the escape sequence (+++) must be issued before sending AT commands to the device. 2.8 Answer an incoming Call When an incoming call is detected the device reports an unsolicited code which may be: Unsolicited code RING +CRING: VOICE +CRING: ASYNC +CRING: REL ASYNC +CRING: SYNC +CRING: REL SYNC +CRING: FAX Reason The extended format of incoming call indication is disabled and a call (voice or data) is incoming. The extended format of incoming call indication is enabled and a voice call is incoming. The extended format of incoming call indication is enabled and an asynchronous transparent data call is incoming. The extended format of incoming call indication is enabled and an asynchronous reliable (not transparent) data call is incoming. The extended format of incoming call indication is enabled and a synchronous transparent data call is incoming. The extended format of incoming call indication is enabled and a synchronous reliable (not transparent) data call is incoming. The extended format of incoming call indication is enabled and a fax call is incoming. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 31 of 117
- Page 1 and 2: GE863-QUAD / PY Software User Guide
- Page 3 and 4: GE863-QUAD / PY Software User Guide
- Page 5 and 6: GE863-QUAD / PY Software User Guide
- Page 7 and 8: GE863-QUAD / PY Software User Guide
- Page 9 and 10: GE863-QUAD / PY Software User Guide
- Page 11 and 12: GE863-QUAD / PY Software User Guide
- Page 13 and 14: GE863-QUAD / PY Software User Guide
- Page 15 and 16: GE863-QUAD / PY Software User Guide
- Page 17 and 18: 2.5.2.3 Provide SIM PIN (only if re
- Page 19 and 20: GE863-QUAD / PY Software User Guide
- Page 21 and 22: GE863-QUAD / PY Software User Guide
- Page 23 and 24: GE863-QUAD / PY Software User Guide
- Page 25 and 26: For example: 1 - Let's assume that
- Page 27 and 28: GE863-QUAD / PY Software User Guide
- Page 29: GE863-QUAD / PY Software User Guide
- Page 33 and 34: GE863-QUAD / PY Software User Guide
- Page 35 and 36: GE863-QUAD / PY Software User Guide
- Page 37 and 38: GE863-QUAD / PY Software User Guide
- Page 39 and 40: AT+CPBR=7 the response may look lik
- Page 41 and 42: 3.1.5 Phonebook entry Delete As fir
- Page 43 and 44: GE863-QUAD / PY Software User Guide
- Page 45 and 46: 3.2.1.1 Set the extended incoming c
- Page 47 and 48: GE863-QUAD / PY Software User Guide
- Page 49 and 50: GE863-QUAD / PY Software User Guide
- Page 51 and 52: GE863-QUAD / PY Software User Guide
- Page 53 and 54: GE863-QUAD / PY Software User Guide
- Page 55 and 56: GE863-QUAD / PY Software User Guide
- Page 57 and 58: GE863-QUAD / PY Software User Guide
- Page 59 and 60: GE863-QUAD / PY Software User Guide
- Page 61 and 62: • wait for OK GE863-QUAD / PY Sof
- Page 63 and 64: - Data Coding Scheme - page number
- Page 65 and 66: GE863-QUAD / PY Software User Guide
- Page 67 and 68: GE863-QUAD / PY Software User Guide
- Page 69 and 70: GE863-QUAD / PY Software User Guide
- Page 71 and 72: GE863-QUAD / PY Software User Guide
- Page 73 and 74: GE863-QUAD / PY Software User Guide
- Page 75 and 76: GE863-QUAD / PY Software User Guide
- Page 77 and 78: GE863-QUAD / PY Software User Guide
- Page 79 and 80: GE863-QUAD / PY Software User Guide
<strong>GE863</strong>-<strong>QUAD</strong> / <strong>PY</strong> <strong>Software</strong> <strong>User</strong> <strong>Guide</strong><br />
1vv0300746 Rev. 1 - 23/10/06<br />
2.7.3.2 Hang up the data call<br />
• Send command ATH<br />
• wait for response NO CARRIER<br />
TIP: during the data call the device remains in data (on line) mode, so the escape sequence<br />
(+++) must be issued before sending AT commands to the device.<br />
2.8 Answer an incoming Call<br />
When an incoming call is detected the device reports an unsolicited code which may be:<br />
Unsolicited code<br />
RING<br />
+CRING: VOICE<br />
+CRING: ASYNC<br />
+CRING: REL ASYNC<br />
+CRING: SYNC<br />
+CRING: REL SYNC<br />
+CRING: FAX<br />
Reason<br />
The extended format of incoming call indication is<br />
disabled and a call (voice or data) is incoming.<br />
The extended format of incoming call indication is<br />
enabled and a voice call is incoming.<br />
The extended format of incoming call indication is<br />
enabled and an asynchronous transparent data call<br />
is incoming.<br />
The extended format of incoming call indication is<br />
enabled and an asynchronous reliable (not<br />
transparent) data call is incoming.<br />
The extended format of incoming call indication is<br />
enabled and a synchronous transparent data call is<br />
incoming.<br />
The extended format of incoming call indication is<br />
enabled and a synchronous reliable (not<br />
transparent) data call is incoming.<br />
The extended format of incoming call indication is<br />
enabled and a fax call is incoming.<br />
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved page 31 of 117