LDT Digital-Compendium CS2-DC-001_11_en
LDT Digital-Compendium CS2-DC-001_11_en
LDT Digital-Compendium CS2-DC-001_11_en
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Littfinski Dat<strong>en</strong>Technik (<strong>LDT</strong>)<br />
D-25492 Heist/Germany • Kleiner Ring 9 • www.ldt-infoc<strong>en</strong>ter.com<br />
•<br />
G<strong>en</strong>eral Note<br />
If it is required to ext<strong>en</strong>d the connection cables of a turnout drive it has<br />
to be tak<strong>en</strong> care of a suffici<strong>en</strong>t diameter of the connection wires. For a<br />
maximum curr<strong>en</strong>t of 1 Ampere at the decoder output is the ordinary<br />
used wiring of 0,14 mm² not suffici<strong>en</strong>t. We recomm<strong>en</strong>d to use wires of<br />
0,5 mm² for a suffici<strong>en</strong>t installation to ext<strong>en</strong>ded turnouts or signals.<br />
It is possible to use the digital curr<strong>en</strong>t for the supply to the decoder<br />
modules. This should be installed on small layouts only because in this<br />
case the exp<strong>en</strong>sive digital curr<strong>en</strong>t will be “wasted” for the curr<strong>en</strong>t supply<br />
to the decoder and for switching the drives.<br />
Von Steuereinheit<br />
oder Booster<br />
From command station<br />
or booster<br />
braun<br />
brown<br />
rot<br />
red<br />
•<br />
<strong>Digital</strong> curr<strong>en</strong>t<br />
supply to the<br />
S-DEC-4-<strong>DC</strong><br />
(page_102)<br />
~ ~<br />
14 .. 18V<br />
Littfinski Dat<strong>en</strong>Technik (<strong>LDT</strong>) 1 R<br />
G G 2 R<br />
KL2<br />
4fach Weich<strong>en</strong>decoder<br />
Accessory Decoder<br />
S-DEC-4<br />
Rev. 2.1<br />
Multi-<strong>Digital</strong><br />
Littfinski Dat<strong>en</strong>Technik<br />
D-25492 Heist<br />
www.ldt-infoc<strong>en</strong>ter.com<br />
Für 4 Doppelspul<strong>en</strong>antriebe für NMRA <strong>DC</strong>C<br />
<strong>Digital</strong>systeme. Schaltstrom: 1 Ampere pro<br />
Ausgang.<br />
Magnetartikel-Decoder<br />
S-DEC-4-<strong>DC</strong><br />
<strong>Digital</strong>-Profi werd<strong>en</strong>!<br />
KL1<br />
Red<br />
Black<br />
J<br />
G S1 red brown<br />
K<br />
G 3 R 4 R<br />
If the available digital curr<strong>en</strong>t (the C<strong>en</strong>tral Station 2 60214 requires<br />
about 3 Ampere and the 60215 about 5 Ampere) will be not suffici<strong>en</strong>t<br />
for the operation of the layout it will be required to use an additional<br />
digital amplifier (= Booster e.g. “DB-2” or “DB-4”). This requires naturally<br />
additional wiring installation and further cost (exp<strong>en</strong>sive digital curr<strong>en</strong>t!).<br />
Page 4 / 8<br />
<strong>LDT</strong> <strong>Digital</strong>-<strong>Comp<strong>en</strong>dium</strong> <strong>CS2</strong>-<strong>DC</strong>-<strong>001</strong>_<strong>11</strong>_<strong>en</strong>