Chapter 1. IBM Flex System FC3171 8 Gb SAN Switch - QLogic

More documents

Recommendations

Info

Table 20. Port Information Data Window entries (Continued) Entry Valid Donor Groups Description The number of separate groups within which extended credits may be donated and assigned Media Group Media Type Media Speed Media Media Transmitter Media Distance Media Vendor Media Vendor ID Media Part Number Media Revision The transceiver fibre type, such as single mode, multi-mode, copper The maximum transceiver speed The transceiver type The transceiver transmitter type, such as longwave, shortwave, electrical The maximum transceiver transmission distance The company that manufactured the SFP The IEEE registered company ID The part number assigned to the SFP Transceiver hardware version Using the Port Statistics data window The Port Statistics data window, shown in Figure 37, displays statistics about port performance. To open the Port Statistics data window, select one or more ports and click the Port Stats data window tab. Figure 37. Port Statistics Data Window 86 IBM Flex System FC3171 8 Gb SAN Switch QuickTools User’s Guide
The Statistics drop-down list is available on the Port Statistics data window, and provides different ways to view detailed port information. Click the down arrow to open the drop-down list, and select Absolute to view the total count of statistics since the last switch or port reset. Select Rate to view the number of statistics counted per second over the polling period. Select Baseline to view the total count of statistics since the last time the baseline was set. When viewing baseline statistics, click the Clear Baseline button to set the current baseline. The baseline will also be set when the switch status changes from unreachable to reachable. Table 21 describes the Port Statistics data window entries. Table 21. Port Statistics Data Window entries Entry Start Time End Time Total Time Al Init AL Init Error Bad Frames BB_CreditRecovery FrameFailure BB_CreditRecovery RRDYFailure Class 2 Frames In Class 2 Frames Out Class 2 Words In Class 2 Words Out Class 3 Frames In Class 3 Frames Out Class 3 Toss Class 3 Words In Class 3 Words Out Decode Errors Description The beginning of the period over which the statistics apply. The start time for the Absolute view is not applicable. The start time for the Rate view is the beginning of polling interval. The start time for the Baseline view is the last time the baseline was set. The last time the statistics were updated on the display. Total time period from start time to end time. Number of times the port entered the initialization state. Number of times the port entered initialization and the initialization failed. Increments count when port has a sync loss. Number of frames that were truncated due to a loss of sync or the frame didn't end with an EOF. Number of times more frames were lost during a credit recovery period than the recovery process could resolve. This value causes a Link Reset to recover the credits. Number of times more R_RDYs were lost during a credit recovery period than the recovery process could resolve. This value causes a Link Reset to recover the credits. Number of class 2 frames received by this port. Number of class 2 frames transmitted by this port. Number of class 2 words received by this port. Number of class 2 words transmitted by this port. Number of class 3 frames received by this port. Number of class 3 frames transmitted by this port. Number of class 3 frames that were discarded by this port. A frame can be discarded because of detection of a missing frame (based on SEQ_CNT), detection of an E_D_TOV timeout, receiving a reject frame, or receiving a frame on an offline port. Number of class 3 words received by this port. Number of class 3 words transmitted by this port. Number of invalid transmission words detected during decoding. Decoding is from the 10-bit characters and special K characters. Chapter 5. Managing ports 87
Page 1:
IBM Flex System FC3171 8 Gb SAN Swi
Page 4 and 5:
Note: Before using this information
Page 6 and 7:
Managing the zoning database . . .
Page 8 and 9:
viii IBM Flex System FC3171 8 Gb SA
Page 10 and 11:
• IBM Flex System FC3171 8 Gb SAN
Page 12 and 13:
4 IBM Flex System FC3171 8 Gb SAN S
Page 14 and 15:
Opening QuickTools After the switch
Page 16 and 17:
Fabric tree QuickTools allows you t
Page 18 and 19:
Table 3. Menu bar options (Continue
Page 20 and 21:
Selecting ports Ports are selectabl
Page 22 and 23:
Viewing software version Exiting Qu
Page 24 and 25:
Event Browser The Event Browser dis
Page 26 and 27:
Filtering the Event Browser Filteri
Page 28 and 29:
Table 5 describes the entries in th
Page 30 and 31:
Creating a nickname To create a dev
Page 32 and 33:
Active Zone Set data window The Act
Page 34 and 35:
Zones Zoning divides the fabric for
Page 36 and 37:
• MaxTotalMembers is 10,000. This
Page 38 and 39:
Table 6. Edit Zoning dialog tool ba
Page 40 and 41:
Saving the zoning database to a fil
Page 42 and 43:
Managing zones Renaming a zone set
Page 44 and 45: Adding zone members You can zone a
Page 46 and 47: Creating an alias To create an alia
Page 48 and 49: 40 IBM Flex System FC3171 8 Gb SAN
Page 50 and 51: Using the Switch data window The Sw
Page 52 and 53: Table 7. Switch data window entries
Page 54 and 55: Table 7. Switch data window entries
Page 56 and 57: Managing user accounts Only the Adm
Page 58 and 59: Removing a user account To remove a
Page 60 and 61: Modifying a user account To modify
Page 62 and 63: Resetting a switch Resetting a swit
Page 64 and 65: Domain ID and domain ID lock The do
Page 66 and 67: Advanced switch properties FDMI is
Page 68 and 69: Managing system services The System
Page 70 and 71: IPv4 and IPv6 addressing The IP con
Page 72 and 73: Network DNS configuration The Netwo
Page 74 and 75: The SNMP configuration defines how
Page 76 and 77: The SNMP v3 Manager dialog allows y
Page 78 and 79: To archive a switch, do the followi
Page 80 and 81: Table 17. Factory default configura
Page 82 and 83: The applicable code versions are:
Page 84 and 85: Table 18. Call Home Setup dialog fi
Page 86 and 87: Using the Call Home profile editor
Page 88 and 89: Table 19 lists the fields in the Ca
Page 90 and 91: Testing Call Home profiles Use the
Page 92 and 93: Information in the Port Information
Page 96 and 97: Table 21. Port Statistics Data Wind
Page 98 and 99: The port settings or characteristic
Page 100 and 101: Table 23 describes the port adminis
Page 102 and 103: I/O Stream Guard The I/O Stream Gua
Page 104 and 105: To run a diagnostics test on a port
Page 106 and 107: Notes: The port map affects the ope
Page 108 and 109: Getting help and information from t
Page 110 and 111: Trademarks IBM, the IBM logo, and i
Page 114 and 115: Frame Data unit consisting of a sta
Page 118 and 119: fabric loop port 92 management 15 m
Page 120: Z zone add member port 36 copy 35 d
show all

Chapter 1. IBM Flex System FC3171 8 Gb SAN Switch - QLogic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?