VL2500 Spot User Manual - Production Services Ireland
VL2500 Spot User Manual - Production Services Ireland VL2500 Spot User Manual - Production Services Ireland
VARI❋LITE® - VL2500 SPOT LUMINAIRE USER’S MANUAL Powering Up Power-Up Procedure Since Lamp On is the default state, the lamp will strike when the luminaire is powered up for the first time. When AC power is applied, the luminaire will immediately begin a calibration sequence that steps it through full pan and tilt movements. The internal color, gobo, and beam mechanisms will also move through a full range of motion. After calibration, the luminaire head will either stop at its "home" position (which positions the pan axis at mid-rotation and the head parallel to the yoke with the lens pointing away from the luminaire upper enclosure) or move to its current DMX-defined position if DMX data is present. All internal mechanisms also move to their "home" or DMX-defined positions. Subsequently, depending on the luminaire’s setting for Lamp Power-Up State (refer to “Menu System Functions” on page 53), when power is applied, the arc lamp will either a) "strike" or ignite - Lamp On (default), b) await calibration and then strike - Cal On, or c) await manual command to strike - Lamp Off. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. To power up: Step 1. At each luminaire, apply power by switching power switch to "I" (ON) position. Luminaire will automatically step through following procedure: a. If Lamp Power-Up State is set to Lamp On, lamp will strike (ignite). b. Luminaire will cycle through calibration and stop at "home" position. c. If Lamp Power-Up State is set to Cal On, lamp will strike (ignite) at end of calibration sequence. 18 05-January-2004 02.9676.0019 A
Align Lamp for Flat Field INSTALLATION : POWERING UP 2 The design of the VL2500 spot luminaire optical system is based on a flat field. A flat field is one where there is no detectable hot spot. After a new lamp is installed, it will be necessary to align the lamp to optimize the beam for the flat field. Knobs located at the luminaire’s backcap will allow adjustment. WARNING: Backcap and adjustment knobs will be HOT during lamp operation. Wear gloves and/or use tools to prevent burns. To align lamp: Step 1. Using internal menus select Lamp test to set beam. See “Menu System Functions” on page 53 for more information. (If using console, set intensity to 100%, open beam size iris and focus for hard edge.) Step 2. Position beam on a white wall at a distance of 10' to 20'. Step 3. At backcap, using Vertical and Horizontal knobs, adjust hot spot to center of beam. Step 4. Using Focus knob, adjust beam for best spot. Note: During this test, the pan and tilt functions of the luminaire are temporarily disabled to allow manual movement of the luminaire head. Pan and tilt functions will be restored when the test is exited. Vertical Horizontal Captive Knob for lamp access (does not adjust beam) Figure 2-7: Lamp Alignment Controls 02.9676.0019 A 05-January-2004 19 Focus
- Page 2 and 3: VARI❋LITE ® is a trademark owned
- Page 4 and 5: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 6 and 7: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 8 and 9: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 10 and 11: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 12 and 13: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 14 and 15: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 16 and 17: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 18 and 19: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 20 and 21: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 22 and 23: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 24 and 25: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 26 and 27: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 28 and 29: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 30 and 31: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 32 and 33: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 36 and 37: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 38 and 39: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 40 and 41: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 42 and 43: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 44 and 45: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 46 and 47: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 48 and 49: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 50 and 51: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 52 and 53: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 54 and 55: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 56 and 57: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 58 and 59: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 60 and 61: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 62 and 63: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 64 and 65: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 66 and 67: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 68 and 69: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 70 and 71: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 72 and 73: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 74 and 75: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 76 and 77: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 78 and 79: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 80 and 81: VARI❋LITE® - VL2500 SPOT LUMINAI
- Page 82 and 83: VARI❋LITE® - VL2500 SPOT LUMINAI
VARI❋LITE® - <strong>VL2500</strong> SPOT LUMINAIRE USER’S MANUAL<br />
Powering Up<br />
Power-Up Procedure<br />
Since Lamp On is the default state, the lamp will strike when the luminaire is powered up for the first<br />
time. When AC power is applied, the luminaire will immediately begin a calibration sequence that<br />
steps it through full pan and tilt movements. The internal color, gobo, and beam mechanisms will also<br />
move through a full range of motion. After calibration, the luminaire head will either stop at its "home"<br />
position (which positions the pan axis at mid-rotation and the head parallel to the yoke with the lens<br />
pointing away from the luminaire upper enclosure) or move to its current DMX-defined position if<br />
DMX data is present. All internal mechanisms also move to their "home" or DMX-defined positions.<br />
Subsequently, depending on the luminaire’s setting for Lamp Power-Up State (refer to “Menu System<br />
Functions” on page 53), when power is applied, the arc lamp will either a) "strike" or ignite - Lamp On<br />
(default), b) await calibration and then strike - Cal On, or c) await manual command to strike - Lamp<br />
Off.<br />
CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and<br />
yoke can move freely without restriction.<br />
To power up:<br />
Step 1. At each luminaire, apply power by switching power switch to "I" (ON) position. Luminaire<br />
will automatically step through following procedure:<br />
a. If Lamp Power-Up State is set to Lamp On, lamp will strike (ignite).<br />
b. Luminaire will cycle through calibration and stop at "home" position.<br />
c. If Lamp Power-Up State is set to Cal On, lamp will strike (ignite) at end of calibration<br />
sequence.<br />
18 05-January-2004 02.9676.0019 A