Crocus SHDSL G703.pdf - FTP Directory Listing

More documents

Recommendations

Info

148 Crocus SHDSL G703 Chapter 6 Reference manual Configuration attributes 6.6 DTE Interface configuration attributes -This section describes the following configuration attributes: • crocusShdslTtRpG703/g703/timeSlots on page 149 • crocusShdslTtRpG703/g703/coding on page 149 • crocusShdslTtRpG703/g703/aisDetection on page 149 • crocusShdslTtRpG703/g703/sqThreshold on page 149 • crocusShdslTtRpG703/g703/sqTime on page 149 • crocusShdslTtRpG703/g703/name on page 150 • crocusShdslTtRpG703/g703/clocking on page 150 • crocusShdslTtRpG703/g703/rdlDetect on page 150 • crocusShdslTtRpG703/g703/ on page 150
Crocus SHDSL G703 Chapter 6 149 Reference manual Configuration attributes crocusShdslTtRpG703/g703/timeSlots This attribute is only present on a G703 Nx64k interface. Use the timeSlots attribute to enable or disable the individual 64 kbps time slots in the framed data stream. Important remark • Do not enable time slot 0 in the local Crocus SHDSL G703 and a non-G703 interface in the remote Crocus SHDSL G703. • In case you use a G703 interface in one Crocus SHDSL and a serial interface is the other Crocus SHDSL, then the auto speed only works when more than 2 time slots (in case of a Crocus SHDSL 1 pair version) or 4 time slots (in case of a Crocus SHDSL 2 pair version) are selected. For more information, refer to 5.7 - Configuring framing and time slots on page 93. Default:ts0=1, other ts=0 Range: enumerated, see below crocusShdslTtRpG703/g703/coding Use the coding attribute to set the G703 interface encoding mode. Possible values are: Default:hdb3 Range: ami / hdb3 Value ami hdb3 Description Alternate Mark Inversion is selected. This is a bipolar code with no zero substitution. High Density Bipolar 3 is selected. This is a modified bipolar code.With HDB3 encoding, more than three consecutive zeroes occurring in the data are replaced by a substitution word. This to ensure a high pulse density. Therefore, data links using the HDB3 code can carry data patterns with a low 1 density. Most of the G703 applications use HDB3 encoding. crocusShdslTtRpG703/g703/aisDetection Use this attribute to enable or disable the detection of the Alarm Indication Signal. Default:enabled Range: enabled / disabled crocusShdslTtRpG703/g703/sqThreshold Use this attribute to set the signal quality threshold. This is the number of errored seconds for which a signal quality alarm is generated. If the sqThreshold value, i.e. the number of errored seconds, is exceeded within the sqTime, then a signal quality (sq) alarm is generated. For example, if 10 (default) or more errored seconds occur within 1 minute (default), then a signal quality alarm is generated. The sqThreshold value ranges from 0 up to 65535. Default:10 Range: 0 … 65535 crocusShdslTtRpG703/g703/sqTime Use this attribute to set the signal quality time. This is the period (in days, hours, minutes and seconds) during which the signal quality threshold is measured. Default:00000d 00h 01m 00s Range: 00000d 00h 00m 00s - 24855d 03h 14m 07s
Page 1 and 2:
Crocus SHDSL G703 User and referenc
Page 3 and 4:
Crocus SHDSL G703 User manual Copyr
Page 5 and 6:
Crocus SHDSL G703 User manual Prefa
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Crocus SHDSL G703 User and referenc
Page 13 and 14:
Crocus SHDSL G703 1 User manual Use
Page 15 and 16:
Crocus SHDSL G703 Chapter 1 3 User
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110: Crocus SHDSL G703 Chapter 5 97 User
Page 111 and 112: Crocus SHDSL G703 Chapter 5 99 User
Page 113 and 114: Crocus SHDSL G703 Chapter 5 101 Use
Page 133 and 134: Crocus SHDSL G703 121 Reference man
Page 135 and 136: Crocus SHDSL G703 Chapter 6 123 Ref
Page 159: Crocus SHDSL G703 Chapter 6 147 Ref
Page 211 and 212:
Crocus SHDSL G703 Chapter 8 199 Ref
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Crocus SHDSL G703 Chapter 10 231 Us
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Crocus SHDSL G703 271 Annex Annex
Page 285 and 286:
Crocus SHDSL G703 Annex A: 273 Anne
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Crocus SHDSL G703 Annex B: 279 Anne
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Crocus SHDSL G703 Annex Index 1 Ind
Page 299 and 300:
Crocus SHDSL G703 Annex Index 3 man
Page 301 and 302:
Crocus SHDSL G703 Annex Index 5 per
show all

Crocus SHDSL G703.pdf - FTP Directory Listing

Create successful ePaper yourself

Delete template?

Save as template?