Crocus SHDSL G703.pdf - FTP Directory Listing
Crocus SHDSL G703.pdf - FTP Directory Listing Crocus SHDSL G703.pdf - FTP Directory Listing
134 Crocus SHDSL G703 Chapter 6 Reference manual Configuration attributes crocusShdslTtRpG703/line/mode This attribute is only present on a Crocus SHDSL G703 2P (2 pair) version. Use the mode attribute to select between single pair or dual pair operation. Default:dualPair Range: singlePair / dualPair When the mode attribute is changed, the Crocus SHDSL G703 reboots. When you change the mode attribute, then make sure that you use the correct speed attribute to set the user speed: If the mode attribute is set to … singlePair, dualPair, then use the attribute … speed to configure the user speed. speed2P to configure the user speed.
Crocus SHDSL G703 Chapter 6 135 Reference manual Configuration attributes crocusShdslTtRpG703/line/minLinePairSpeed Use the minLinePairSpeed attribute to determine what the minimum speed on the line pair has to be when the Crocus SHDSL G703 trains. For more information on the minimum line pair speed, refer to 5.6 - Configuring the minimum line speed on page 87. Default: Range: 192kbps up to 2048kbps (in steps of 64kbps) crocusShdslTtRpG703/line/retrain Use the retrain attribute to determine when the Crocus SHDSL G703 should retrain. Default:- Range: structure, see below The retrain criteria The following criteria determine when to retrain: Criterion no SHDSL frame synchronisation SHDSL frame CRC error threshold exceeded signal to noise too low Description When the Crocus SHDSL G703 cannot synchronise on the SHDSL framing, it retrains. SHDSL framing sends 166 blocks per second over the line, independently of the speed. Each block has a CRC check. When a certain percentage of frames has a CRC error, the Crocus SHDSL G703 retrains. When the signal to noise ratio becomes too low during a certain period of time, the Crocus SHDSL G703 retrains.
- Page 95 and 96: Crocus SHDSL G703 Chapter 5 83 User
- Page 97 and 98: Crocus SHDSL G703 Chapter 5 85 User
- Page 99 and 100: Crocus SHDSL G703 Chapter 5 87 User
- Page 101 and 102: Crocus SHDSL G703 Chapter 5 89 User
- Page 103 and 104: Crocus SHDSL G703 Chapter 5 91 User
- Page 105 and 106: Crocus SHDSL G703 Chapter 5 93 User
- Page 107 and 108: Crocus SHDSL G703 Chapter 5 95 User
- Page 109 and 110: Crocus SHDSL G703 Chapter 5 97 User
- Page 111 and 112: Crocus SHDSL G703 Chapter 5 99 User
- Page 113 and 114: Crocus SHDSL G703 Chapter 5 101 Use
- Page 115 and 116: Crocus SHDSL G703 Chapter 5 103 Use
- Page 117 and 118: Crocus SHDSL G703 Chapter 5 105 Use
- Page 119 and 120: Crocus SHDSL G703 Chapter 5 107 Use
- Page 121 and 122: Crocus SHDSL G703 Chapter 5 109 Use
- Page 123 and 124: Crocus SHDSL G703 Chapter 5 111 Use
- Page 125 and 126: Crocus SHDSL G703 Chapter 5 113 Use
- Page 127 and 128: Crocus SHDSL G703 Chapter 5 115 Use
- Page 129 and 130: Crocus SHDSL G703 Chapter 5 117 Use
- Page 131 and 132: Crocus SHDSL G703 Chapter 5 119 Use
- Page 133 and 134: Crocus SHDSL G703 121 Reference man
- Page 135 and 136: Crocus SHDSL G703 Chapter 6 123 Ref
- Page 137 and 138: Crocus SHDSL G703 Chapter 6 125 Ref
- Page 139 and 140: Crocus SHDSL G703 Chapter 6 127 Ref
- Page 141 and 142: Crocus SHDSL G703 Chapter 6 129 Ref
- Page 143 and 144: Crocus SHDSL G703 Chapter 6 131 Ref
- Page 145: Crocus SHDSL G703 Chapter 6 133 Ref
- Page 149 and 150: Crocus SHDSL G703 Chapter 6 137 Ref
- Page 151 and 152: Crocus SHDSL G703 Chapter 6 139 Ref
- Page 153 and 154: Crocus SHDSL G703 Chapter 6 141 Ref
- Page 155 and 156: Crocus SHDSL G703 Chapter 6 143 Ref
- Page 157 and 158: Crocus SHDSL G703 Chapter 6 145 Ref
- Page 159 and 160: Crocus SHDSL G703 Chapter 6 147 Ref
- Page 161 and 162: Crocus SHDSL G703 Chapter 6 149 Ref
- Page 163 and 164: Crocus SHDSL G703 Chapter 6 151 Ref
- Page 165 and 166: Crocus SHDSL G703 Chapter 6 153 Ref
- Page 167 and 168: Crocus SHDSL G703 Chapter 7 155 Ref
- Page 169 and 170: Crocus SHDSL G703 Chapter 7 157 Ref
- Page 171 and 172: Crocus SHDSL G703 Chapter 7 159 Ref
- Page 173 and 174: Crocus SHDSL G703 Chapter 7 161 Ref
- Page 175 and 176: Crocus SHDSL G703 Chapter 7 163 Ref
- Page 177 and 178: Crocus SHDSL G703 Chapter 7 165 Ref
- Page 179 and 180: Crocus SHDSL G703 Chapter 7 167 Ref
- Page 181 and 182: Crocus SHDSL G703 Chapter 7 169 Ref
- Page 183 and 184: Crocus SHDSL G703 Chapter 7 171 Ref
- Page 185 and 186: Crocus SHDSL G703 Chapter 7 173 Ref
- Page 187 and 188: Crocus SHDSL G703 Chapter 7 175 Ref
- Page 189 and 190: Crocus SHDSL G703 Chapter 7 177 Ref
- Page 191 and 192: Crocus SHDSL G703 Chapter 7 179 Ref
- Page 193 and 194: Crocus SHDSL G703 Chapter 7 181 Ref
- Page 195 and 196: Crocus SHDSL G703 Chapter 7 183 Ref
134 <strong>Crocus</strong> <strong>SHDSL</strong> G703 Chapter 6<br />
Reference manual<br />
Configuration attributes<br />
crocusShdslTtRpG703/line/mode<br />
This attribute is only present on a <strong>Crocus</strong> <strong>SHDSL</strong> G703 2P (2 pair) version.<br />
Use the mode attribute to select between single pair or dual pair operation.<br />
Default:dualPair<br />
Range: singlePair / dualPair<br />
When the mode attribute is changed, the <strong>Crocus</strong> <strong>SHDSL</strong> G703 reboots.<br />
When you change the mode attribute, then make sure that you use the correct speed attribute to set the<br />
user speed:<br />
If the mode attribute is set to …<br />
singlePair,<br />
dualPair,<br />
then use the attribute …<br />
speed to configure the user speed.<br />
speed2P to configure the user speed.