NGC-40 Hardware Manager - Pentair Thermal Management
NGC-40 Hardware Manager - Pentair Thermal Management NGC-40 Hardware Manager - Pentair Thermal Management
The Edit Settings screen includes all the communication parameters for the NGC-40-BRIDGE, including the settings for each COM port, as well as the Ethernet communication settings. The user can also enter up to 40 characters as a NGC-40-BRIDGE Tag, to more easily identify which NGC-40-BRIDGE they are connected to. You will see a popup text when you enter the configuration screen. The popup will differ based on the NGC-40-BRIDGE mode: If the switch is in RUN mode: If the switch is in SET mode: THERMAL MANAGEMENT SOLUTIONS EN-DigiTraceNGC40HWManager-IM-H58450 04/13 16/39
IMPORTANT: After making changes to the communication parameters the RUN/SET switch MUST be returned to RUN mode for the changes to take effect. Most of the General Information fields are read-only and are shown to provide more information about the NGC-40-BRIDGE. Firmware Version - shows which version is currently installed in the NGC-40-BRIDGE. This can be updated with DHM NGC-40 by selecting “Upload Firmware to an NGC-40-BRIDGE” from the main screen. Ethernet MAC Address - is a unique address used for communications over Ethernet. This value cannot be changed. Operating System Version - shows which OS is currently being run in the NGC-40-BRIDGE. This value also cannot be changed. THERMAL MANAGEMENT SOLUTIONS EN-DigiTraceNGC40HWManager-IM-H58450 04/13 17/39
- Page 1 and 2: USER MANUAL NGC-40 Hardware Manager
- Page 3 and 4: Section − 1 INTRODUCTION 1.1 Welc
- Page 5 and 6: When the file location and access o
- Page 7 and 8: During installation a program icon
- Page 9 and 10: The connection settings screen will
- Page 11 and 12: 3.2 Connecting via Ethernet If you
- Page 13 and 14: A window will appear. Enter the IP
- Page 15: 3.3 Configuration of the NGC-40-BRI
- Page 19 and 20: COM 1 and COM 2 are the RS-485 port
- Page 21 and 22: If you are done making changes, ret
- Page 23 and 24: Section − 4 WORKING WITH CONNECTE
- Page 25 and 26: THERMAL MANAGEMENT SOLUTIONS EN-Dig
- Page 27 and 28: Information about the version of NG
- Page 29 and 30: Status - shows the current status.
- Page 31 and 32: Step 2 Cycle Power on the NGC-40-B
- Page 33 and 34: Once the NGC-40-BRIDGE has been boo
- Page 35 and 36: After you have selected the file it
- Page 37 and 38: The status bar displays the progres
- Page 39: WWW.THERMAL.PENTAIR.COM NORTH AMERI
The Edit Settings screen includes all the communication<br />
parameters for the <strong>NGC</strong>-<strong>40</strong>-BRIDGE, including the settings for<br />
each COM port, as well as the Ethernet communication settings.<br />
The user can also enter up to <strong>40</strong> characters as a <strong>NGC</strong>-<strong>40</strong>-BRIDGE<br />
Tag, to more easily identify which <strong>NGC</strong>-<strong>40</strong>-BRIDGE they are<br />
connected to.<br />
You will see a popup text when you enter the configuration screen.<br />
The popup will differ based on the <strong>NGC</strong>-<strong>40</strong>-BRIDGE mode:<br />
If the switch is in RUN mode:<br />
If the switch is in SET mode:<br />
THERMAL MANAGEMENT SOLUTIONS EN-DigiTrace<strong>NGC</strong><strong>40</strong>HW<strong>Manager</strong>-IM-H58450 04/13 16/39