PuMPING SYSTEMS - Rutherford Equipment, Inc.

Vertical Tanks, Pump Kits, Bulkheads 

Pumping systems 

PUMPING SYSTEMS 

The following kits are primarily designed to be used with a small 

capacity pump like Blackmer’s LGF1C (10 GPM) or LGF1PC (15 

GPM) 

For a pumping system to perform properly, you must have high 

quality equipment installed in accordance with the manufacturer’s 

recommendations and the following good installation practices: 

1. The tank should be installed with as much vertical distance 

from the bottom tank outlet to the pump inlet as practical. The 

minimum recommended distance from the bottom of the tank 

to the ground is 16” for good pump performance. 

PUMPING SYSTEMS (continued) 

LF1-A 

Economy Pump Kit 

This kit includes a manually operated liquid withdrawal valve 

with a 1” outlet. All fittings to the pump are 1”. 

LF1-B 

Deluxe Pump Kit 

Deluxe kit includes Fisher’s 1 1/4” internal valve. All piping 

components are 1 1/4”. 

See appendix for material lists & schematics of these kits. 

2. Only bottom tank outlets should be used to supply gas to liquid 

pumps, and the size of these outlets should be no less than the 

inlet of the pump. There should be no restrictive fittings on the 

inlet side of the pump. 

3. The pump should be located as close to the tank outlet as 

practical. A LP gas pump can push gas for reasonable distances, 

but cannot suck gas. Liquid gas must be fed to the pump by 

gravity. 

BULKHEADS 

BULK PLANT BULKHEADS 

4. All positive displacement pumps require a bypass line to return 

gas back to the tank. The Blackmer LGF1E and LGF1PE pumps 

have built in bypass valves. A line must be run between the 

pump and the tank to protect the pump against excessive 

differential pressure. 

G 

5. Proper electrical wiring connections and correct wire size are 

important for good pump performance. Be sure the motor 

terminals are connected correctly for the voltage and rotation 

being used. Listed below are general recommendations for 

the minimal wire size for more common wiring runs on 1 HP and 

1 1/2 HP single phase motors. Please comply with the motor 

manufacturer’s requirements concerning this matter. 

ITEM# 

COUPLINGS 

STH16X10 2” and 1 1/4” 

STH16X16 Two 2” 

STH16X16X10 Two 2”, One 1 1/4” 

STH24X16 3” and 2” 

STH24X16X10 3”, 2”, and 1 1/4” 

STH24X16X16 3” and Two 2” 

Length of Run Voltage Wire Size 

Motor Size: 1 HP Single Phase 

100’ 115 #8 

100’ 230 #10 

200’ 115 #6 

200’ 230 #8 

Motor Size: 1 1/2 HP Single Phase 

100’ 115 #4 

100’ 230 #10 

200’ 115 #0 

200’ 230 #8 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 69 -

H 

Blackmer pumps 

BLACKMER PUMPS 

LGF DRIVE STYLE 

Flange Mounting - 

Direct Motor Drive 

These small positive displacement pumps are 

ideal for filling cylinders and motor fuel tanks. 

They mount directly to a C-face motor & have 

built in “back to the tank” bypass valves. 

Pump Only 

Item # Size Capacity 

LGF1E 1” 10 GPM 

LGF1PE 1” 15 GPM 

LGRLF1-1 1/4 1 1/4” 18 GPM 

LGF1 Series 

w/ 115/230V Motor 

Item # * Size HP Capacity 

LGF1E-101 1” 1 10 GPM 

LGF1PE-151 1” 1 1/2 15 GPM 

LGRLF-151 1 1/4” 1 1/2 18 GPM 

* To include a switch with the assembly, add an “A” suffix to the item #. (LGFIE-101A) 

LDF1 Series 

Dispenser Pumps 

Similar to the LGF1 Series, but these are 

assembled with left-hand rotation which 

will allow them to retrofit in place of Corken 

C Series pumps. These pumps require an 

external bypass valve. 

Item# Size Capacity 

LDF1A 1” 10 GPM 

LDF1PA 1” 15 GPM 

DM Drive Style 

Bracket Mounting - 

Direct Motor Drive 

These durable motor speed pumps offer 

capacities up to 35 GPM and are ideal for 

motor fueling, multiple station cylinder filling 

and a variety or small transfer jobs. They are 

designed for foot mounting to a common 

base plate. 

Pump Only 


LGL1-1/4 1 1/4” 20 GPM 

LGL1-1/2 1 1/2” 30 GPM 

Pump Assembly 

Pump, coupling and coupling guard, 

mounted on a common base, ready to 

accept a standard NEMA motor. 


LGL1-1/4DM 1 1/4” 20 GPM 

LGL1-1/2DM 1 1/2” 30 GPM 

Blackmer Pumps (continued) 

* Comes with one 2” flanged elbow. For two elbows, order TLGLF3C-2. 

Pumps 

VB Drive Style 

Base Mounted - V-Belt 

Drive 

Pump Only 

Capacity is at 640 RPM and 50 psi differential 

pressure. 


LGLD2E 2” 67 GPM 

LGLD3E 3” 133 GPM 

LGLD4 4” inlet 3” outlet 270 GPM 

Pump Assembly 

Pump, hubs, sheaves, high-torque triple 

V-belts and belt guard mounted on a 

common base, ready to accept a standard 

NEMA motor. Capacity at 640 RPM and 50 

psi differential pressure. 


LGLD2E-VB 2” 67 GPM 

LGLD3E-VB 3” 133 GPM 

LGLD4-VB 4” inlet 3” outlet 270 GPM 

Flange Mounted Pumps 

For bobtails & 

transports 

Capacity is at 870 RPM and 50 psi differential 

pressure. 

Item # Inlet Aux. Inlet Outlet Capacity 

TLGLF3C* 3” flange 2” FNPT 2” FNPT 100 GPM 

TLGLF4B 4” flange 3” FNPT Dual 2” FNPT 379 GPM 

Hydraulic Drive System 

Blackmer’s HYDRIVE is a filly integrated hydraulic drive system. A 

typical system includes a P.T.O., hydraulic pump, Hydrive cooler/ 

controller, pump control valve, speed control valve, and mounting 

hardware. Hydraulic motor adapter kits are available to retrofit 

existing Blackmer pumps for hydraulic drive operation. Each system 

is factory engineered to fit your application. 

- 70 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293

By-Pass Valves, Repair Kits & Individual Parts 

BY-PASS VALVES 

Blackmer By-pass 

Valves 

Differential bypass valves are designed 

to protect pumps and system 

components from excessive pressure 

damage. Weld flanges are available 

by special order. 

Pump Pressure Adjust. 

Item # Size Size Setting Range Cap. 

BV-3/4 3/4” 1 1/4”-1 1/2” 95 psi 70-100 psi 50 GPM 

BV-1 1” 1 1/4”-1 1/2” 95 psi 70-100 psi 50 GPM 

BV-1 1/4 1 1/4” 1 1/2”-2” 95 psi 70-125 psi 125 GPM 

BV-1 1/2 1 1/2” 2”-3” 95 psi 70-125 psi 125 GPM 

BV-2-30 2” 3”-4” 30 psi 20-40 psi 225 GPM 

BV-2-55 2” 3”-4” 55 psi 41-70 psi 225 GPM 

BV-2-95 2” 3”-4” 95 psi 90-125 psi 225 GPM 

Fisher By-pass Valves 

. 

Pump Pressure Adjust. 

Item # Size Size Setting Range 

N100A-10-2 1 1/4” 2”-3” 115 psi 50-150 psi 

N100A-12-2 1 1/2” 2”-3” 115 psi 50-150 psi 

N100-16-2 2” 4” 115 psi 50-150 psi 

Blackmer pump parts 

Blackmer Rebuild Kits 

Rebuild kits include maintenance kits, rotor & shaft and liners.” 

* These kits include new and improved QA seal assemblies and 

double end rotor and shaft. 

Kit Number Pump Replaces 

899076 LGRLG-1 1/4 - 4 Vane 889017 

899077 LGL-1 1/4 - 4 Vane 889018 

899078 LGL-1 1/2 - 4 Vane 899019 

899076 LGRLF-1 1/4 - 8 Vane 

899077 LGL-1 1/4 - 8 Vane 

899078 LGL-1 1/2 - 8 Vane 

899079 LGLD2E* 

899081 LGLD3E* 

899080 TLGLF3C* 

899022 TLGLF4A & LGLD-4 

899124 TLGLF4B 

Note: All 2" to 4" pumps now have the new "A" seal. 

Blackmer Maintenance Kits 

Maintenance kits do not include pump relief valve parts. 

* These kits include new and improved QA seal assemblies 

Kit Number Pump Replaces Add Pushrods 

898994 LGF1E & PE - 4 Vane 892950 

898994 LGF1E & PE - 6 Vane 

898917 LGRLG-1 1/4 - 4 Vane 892302 

898918 LGL-1 1/4 - 4 Vane *898976 (2) 123076 

898919 LGL-1 1/2 - 4 Vane *898976 (2) 123401 

898976 LGRLF-LGL 1 1/4 & LGL1’s - 8 Vane (2) 123009 

898979 LGLD2E* 894420 

898981 LGLD3E* 894427 

898922 LGLD4* 

898980 TLGLF3C* 895123 

898922 TLGLF4A* 892031 

899224 TLGLF4B 

*Denotes necessary components not included in maintenance kit. 

H 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 71 -


BLACKMER PARTS LIST 

PUMP MODELS: LGF1E, LGB1E, LGF1PE, LGB1PE 

and Discontinued Models 

LGF1D, LGB1D, LGF1PD, LGB1PD, LGF1C, LGB1C, LGF1PC, LGB1PC 

(See Instructions 501-A00 for Installation, Operation and Maintenance) 

LOCKNUT TOOL 

H 

Ref. 

No. 

Description 

Parts 

per 

Pump 

Part No. 

Ref. 

No. 

Description 

Parts 

per 

Pump 

Part No. 

2 Adjusting Screw – Relief Valve (R/V) 1 432901 28 † Capscrews – Bearing Cover 4 920080 

3 Locknut – Adjusting Screw 1 922811 28A † Bracket Mounting Screws 4 920090 

4 Cover – R/V 1 412901 28B † Bracket Mounting Screws 4 920101 

4A O-Ring – Spring Guide 1 

1 711940 28C Guard Screw 1 920026 

7 Spring Guide – R/V 1 422901 Coupling Half – Pump 906150 

8 Spring – R/V 1 472901 Coupling Half – Motor (56C) 906151 

9 Valve – R/V 1 452901 

34 Coupling Half – Motor 

1 

(143-145TC/184C) 

906147 

9A Disc – R/V 1 442901 

Coupling Spider 

906155 

10 O-Ring – R/V Cover 1 

1 701965 35 Key – Shaft 1 

1 909126 

12 † Cylinder – LGF1, LGB1 022914 72 O-Ring – Head 1 

711941 

1 

Cylinder – LGF1P, LGB1P 

022915 73 Gage Plug (1/4”) 2 908198 

13 

Rotor & Shaft Assembly, Six Vane 2 

73A † Plug (3/4”), External Bypass 1 908225 

1 262907 

(Includes Ref. Nos. 24A & 24B) 

76 Grease Fitting 2 317815 

14 Vane – Duravane (Std.) 3 4, 6 

1 092913 76A Grease Relief Fitting 2 701992 

20 † Head 1 032905 104 Grease Seal 1 

1 331934 

21 Capscrews – Head 4 920178 Bracket - (base mount) - LGB1(P)D 832913 

24 Ball Bearing 2 

108 

1 

903405 

Bracket (C-faced footless) - LGF1(P)D 

832912 

24A Locknut – Bearing 2 903531 108A Capscrews – Bracket 4 920331 

24B Lockwasher – Bearing 2 

1 903532 108B Bracket (C-faced footed) SEE PAGE 2 

26 † Gasket – Bearing Cover 1 

1 383075 186 Guard 1 804120 

27 † Bearing Cover 1 043071 Tool - Locknut 903090 

Kit – Maintenance (4-Vane) 898916 

Kit – Maintenance (6-Vane) 898994 

1 Included in Maintenance Kit. 

2 Discontinued 'D' and 'C' models shipped with a 4-vane rotor. The current 6-vane rotor is fully interchangeable as 

long as the slotted vanes (pn 092913) are used. 

3 The current slotted vanes (pn 092913) may be used in either the 6-vane or 4-vane rotors. 

The discontinued solid vanes may be used in the 4-vane rotors ONLY. Always install the vanes with the slot facing the direction of rotation. 

† To fit the LGB1(P)C, LGF1(P)C use: Ref. No. 12-022902/022911 respectively, Ref. No. 20-032902, Ref. No. 26-382901, Ref. No. 27-042901, 

Ref. No. 28-920203, Ref. No. 28A & B-920230, Ref. No. 73A-908198, and Ref. No.108-832901/832905 respectively. 

Keep this parts list with Installation, Operation and Maintenance Instructions. 

- 72 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump models: lgf1e, lgb1e, lgf1pe, lgb1pe (continued) 

Ref. 

No. 

MECHANICAL SEAL 

Part Name 

Parts 

Per 

Pump 

Part No. 

153 Mechanical Seal Assembly 2 

1 332920 

153A** Jacket Assembly – Seal 2 332922 

153B** Stationary Seat (Steel) 2 332901 

153D O-Ring – Stationary Seat (Buna-N) 2 711916 

153F** Seal Face (Carbon) 2 332902 

153G O-ring – Rotating (Buna-N) 2 711939 

1 Included in Maintenance Kit ** Ref. Nos. 153A, 153B & 153F are not available as separate repair parts. 

Ref. 

No. 

MOUNTING BRACKET 

Part Name 

Parts 

Per 

Pump 

Part No. 

108B Bracket (C-faced footed) – LGF1(P)D 1 833000 

H 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 73 -



PUMP MODELS: LGRL1.25, LGRLF1.25A, LGL1.25, 

LGLF1.25A, LGL1.5, LGLF1.5A 

and discontinued models: LGRLF1.25, LGLF1.25 

See Instructions 501-B00 for Installation, Operation and Maintenance 

LOCKNUT TOOL 

H 

Ref. 

No. 

Description 

Parts 

per 

Pump 

Part No. 

Ref. 

No. 

4-Vane Rotor 7 

Description 

Parts 

per 

Pump 

Part No. 

1 Cap – Relief Valve (R/V) 1 413200 27A Bearing Cover – Outboard 1 043071 

2 Adjusting Screw – R/V 1 433909 28 Capscrews – Bearing Cover 4 4 - 8 920080 

3 Locknut – Adjusting Screw 1 922923 35 Shaft Key 1 

1 909125 

4 Cover – R/V 1 413076 41 Liner – LGRL(F)1.25 [8 - Vane Only] 1 

2 183019 

7 Spring Guide – R/V 1 423955 Liner – LGL(F)1.25 [8 - Vane Only] 

2 183020 

8 Spring – R/V (81 – 125 psi) 1 471428 Liner – LGL(F)1.5 [8 - Vane Only] 

2 183310 

9 Valve - R/V 1 453077 71 Disc 2 

1 063075 

10 O-Ring – R/V Cover 1 

1 711924 72 O-Ring – Head 2 

1 701918 

12 Casing with feet (1.25) 1 013075 73 Gage Plug (1/4”) 1 908198 

Casing with feet (1.5) 013376 73A Gage Plug (3/4”) 1 

6 908225 

13 Rotor & Shaft Assembly, Eight 1 

2 262300 74 Setscrew – Liner 1 922088 

Vane (with Ref. Nos. 24A & 24B) 76 Grease Fitting 2 317815 

14 Vane – Duravane 8 


20 Head 2 033073 88 O-Ring – R/V Cap 1 

1 701949 

21 Capscrews – Head 16 920276 104 Grease Seal 1 

1 331927 


1 903114 — Tool - Locknut — 903090 

24A Locknut – Bearing 2 

2 903534 — Kit - Maintenance [8 Vane] — 898976 


1 903533 — Kit - Rebuild LGRL(F)1.25(A) [8 Vane] — 899076 

26 Gasket - Bearing Cover 3 1-2 

1 383075 — Kit - Rebuild LGL(F)1.25(A) [8 Vane] — 899077 

27 Bearing Cover – Inboard 5 0-1 043070 — Kit - Rebuild LGL(F)1.5(A) [8 Vane] — 899078 

1 Included in Maintenance Kits and Rebuild Kits 

2 Included in Rebuild Kits. 

3, 4, 5 Applies to LG(R)LF pump models only: 

3 Use one outboard 

4 Use four outboard 

6 Ref. No. 73A: Older pumps may use a 1/4” plug (pn 908198) or 1/2” plug (pn 908215). 

7 See opposite side re parts for older pumps fitted with a 4-vane rotor. 

Note: Earlier model pumps used taper pins, which are no longer required. 


5 Use none. 

- 74 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump models lgr1.25, lgrlf1.25A, lgl1.25, lglf1.25a, lgl1.5, lglf1.5a (Continued) 

FLANGE ‘F’ MOUNTING 

Ref. No. 

Description 

Parts 

per Part No. 

Pump 

12A 

Casing without Feet – LG(R)LF1.25 013077 

1 

Casing without Feet – LGLF1.5 

013377 

26 Gasket - Bearing Cover 1 383075 

28A Bracket Mounting Screws 4 920101 

28C Guard Screw 1 920026 

Coupling Half – Pump 906147 

Coupling Spider 906155 

Coupling Half – Motor (56C) 906151 

34 Coupling Half – Motor 

1 

(143TC,145TC,184C) 

906147 

Coupling Half – Motor 

(182TC,184TC,215C) 

906146 

56 Capscrews – Adapter Ring Mounting 4 920480 


76A Grease Relief Fitting 1 701992 

86 

Motor Adapter Ring- 

182TC,184TC,215C 

1 832914 

104 Grease Seal 1 331927 

108 6 Mounting Bracket 

Includes Ref. Nos. 76 & 76A 

1 832912 

108B Capscrews - Bracket 4 920331 

186 Guard 1 804120 

6 Use (P/N 833000 – Mounting Bracket w/ feet) on 

discontinued models LG(R)LF1.25 and LGLF1.5 


Ref. 

No. 

Part Name 

Parts 

Per 

Pump 


Part No. 

1 333045 

153A Stationary Seat ( Hardened Steel ) 2 ** 

153B Seal Face ( Carbon ) 2 ** 

153C Jacket Assembly 2 ** 

153D O-Ring – Stationary (Buna-N) 2 711916 

153E O-Ring – Rotating (Buna-N) 2 711915 

1 Included in Maintenance Kits and Rebuild Kits 

** NOTE: Mechanical Seal Ref. No. 153 is only sold as a complete assembly. 

Ref. Nos. 153A, 153B & 153C are not available as 

separate replacement parts. 

H 

4-VANE ROTOR/SHAFT PARTS 

Ref. 

No. 

Part Name 

Parts 

Per 

Pump 

Part No. Part Name Part No. 

13A Rotor & Shaft Assembly, Four Vane 1 

2 263076 Kit – Maint LGRL(F)1.25A [4 Vane] 898917 

(Includes Ref. Nos. 24A & 24B) Kit - Maint LGL(F)1.25(A) [4 Vane] 898918 

14 Vane – Duravane 4 

1 093088 Kit - Maint LGL(F)1.5(A) [4 Vane] 898919 

Liner – LGRL(F)1.25 [4 - Vane Only] 

2 183003 Kit - Rebuild LGRL(F)1.25A [4 Vane] 899017 

41A Liner – LGL(F)1.25 [4 - Vane Only] 1 

2 183004 Kit - Rebuild LGL(F)1.25(A) [4 Vane] 899018 

Liner – LGL(F)1.5 [4 - Vane Only] 

2 183301 Kit - Rebuild LGL(F)1.5(A) [4 Vane] 899019 

Push Rod – LGRL(F)1.25 

1 123004 

77 Push Rod – LGL(F)1.25 2 

1 123076 

Push Rod LGL(F)1.5 

1 123401 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 75 -



PUMP MODELS: LGLD2E, LGL2E, LGLD3E, LGL3E 

See Instructions 501-C00 for Installation, Operation and Maintenance 

LOCKNUT TOOL 

H 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Size 2 

Part No. 

Size 3 

Part No. 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Size 2 

Part No. 

Size 3 

Part No. 

4 Cover - Relief Valve (R/V) 1 414401 415113 35 Key - Shaft 1 

1 909130 1 909130 

5 Capscrews - R/V Cover 6 920331 920331 41 Liner 1 

2 184405 2 185111 

8 Spring - R/V 1 471423 475135 Flange - NPT 654401 655112 

42 

2 

9 Valve - R/V 1 454405 455129 Flange - Weld 

654405 655102 

10 O-Ring - R/V Cover 1 

1 701919 1 701925 42A O-Ring - Flange 2 

1 702004 1 702002 

12 Casing 1 014405 015127 Capscrew - NPT Flange 920384 920547 

13 Rotor & Shaft Asy. - LGL 1 264443 265149 42B 8 

Capscrew - Weld Flange 

920351 920510 

(Includes Ref. Nos. 24A & 24B) 71 Disc 2 

1 064412 1 065112 

13A Rotor & Shaft Asy. ñ LGLD 5 1 

2 264445 2 265148 72 O-Ring - Head 2 

1 702022 1 702041 

(Includes Ref. Nos. 24A & 24B) 73 Gage Plug 2 908198 908198 

14 Vane - Duravane (Std.) 6 

1 091419 1 095131 74 Key ñ Liner 1 

2, 6 183991 2 185191 

20 Head 2 034416 035128 76 Grease Fitting 2 317815 317815 

21 Capscrews - Head (Size 2) 32 920351 N/A 76A Grease Relief Fitting 2 701992 701992 

Capscrews - Head (Size 3) 40 N/A 920369 77 Push Rod 3 

1 123905 1 125105 


1 903156 1 903172 104 Grease Seal 1 

1, 3 331918 1, 3 331908 

24A Locknut - Bearing 2 

2 903521 2 903523 123A Dirt Shield 1 

1, 3 701480 N/A 

24B Lockwasher - Bearing 2 

903522 1 903524 Shaft Protector 

26 Gasket - Bearing Cover 2 

383940 1 385125 186 (LGLD Models Only) 

1 341601 341801 

27 Bearing Cover (Inboard) 3 1 041431 041815 ó Tool - Locknut ó 903091 903091 

27A Bearing Cover (Outboard) 4 1 041433 041817 ó Kit ñ Maintenance ó 898979 898981 

28 Capscrews - Bearing Cover 8 - 12 920285 920285 ó Kit ñ Rebuild ó 899079 899081 

1 Included in Maintenance Kit and Rebuild Kit 

2 Included in Rebuild Kit 

The following applies to double end shaft pump models LGLD2E, LGLD3E: 3 Use Two 

5 Double-Ended Rotor & Shaft. 

6 Pump models before 1995 require key 184407. 


4 Use None 

- 76 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump models: lgld2e, lgl2e, lgld3e, lgl3e (continued) 

MECHANICAL SEAL ñ NH 3 OR DUAL SERVICE ñ SNCN (ID Code = QA) 

Parts 

Ref. 

Size 2 Size 3 

Part Name 

Per 

No. 

Part No. Part No. 

Pump 


1 334439 1 335225 

153A Stationary Seat (Steel) 2 ** ** 

153B Seal Face (Carbon) 2 ** ** 

153C Jacket Assembly 2 ** ** 

153D O-Ring - Stationary (Buna-N) 2 711924 702025 

153E O-Ring Rotating (Buna-N) 2 711918 711912 



Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts. 

OPTIONAL HYDRAULIC MOTOR ADAPTER PARTS 

Ref. No. 

Part Name 

Parts Per Size 2 Size 3 

Pump Part No. Part No. 

See Below Hydraulic Motor Adapter Kit * See Below 894425 895140 

26A Gasket- Hydraulic Motor Adapter 1 383940 381817 

28A Capscrew ñ Hydraulic Motor Adapter / Head 4 / 6 920369 920369 

34 

Coupling w/ Setscrew ñ 

906967 906967 

1 

1.25î straight key hydraulic motor shaft 

35 Key ñ Coupling 1 909184 909184 

76 Grease Fitting 1 317185 317815 

76A Grease Relief Fitting 1 701992 701992 

135 Hydraulic Motor Adapter ñ SAE A Flange 1 041827 041831 

135A Capscrew ñ Adapter / Motor 2 920510 920510 

* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two piece design ñ 

refer to page 206-C00. 

H 

LGLD2E LGLD3 E 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 77 -



PUMP MODELS: LGLD4A, LGL4A 

DISCONTINUED MODELS: LGL4, LGLD4 

(See Instructions 501-E00 for Installation, Operation and Maintenance) 

LOCKNUT TOOL 

H 

` 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

1 Cap - Relief Valve (R/V) 1 413952 28 Capscrews - Bearing Cover 12 920286 

2 Adjusting Screw - R/V 1 NOTE 3 35 Key – Shaft 1 

1 909183 

3 Locknut - Adjusting Screw 1 NOTE 3 41 Liner 1 

2 182000 

4 Cover - R/V 1 412001 Flange - 3" NPT 652012 

5 Capscrew - R/V Cover 4 920663 42 Flange - 3" Weld 1 - 2 652007 

7 Spring Guide - R/V 1 426355 

Flange - 4" Weld 

652005 

8 Spring - R/V 1 NOTE 3 42A O-Ring - NPT, Weld Flange 2 

1 701937 

9 Valve - R/V 1 452001 Capscrew - NPT Flange 920663 


42B 

8 

701946 

Capscrew - Weld Flange 

920640 

12 Casing 1 NOTE 3 71 Disc 2 

1 062039 

13 

Rotor & Shaft Asy, Dbl. End - LGLD4(A) 

71A Machine Screw - Disc 8 

920015 

262024 

(Includes Ref. No. 24A & 24B) 

71B* Lockwasher - Machine Screw 8 

909634 

1 

Rotor & Shaft Asy, Sgl. End - LGL4(A) 

72 O-Ring - Head 2 

702039 

262023 

(Includes Ref. No. 24A & 24B) 

73 Gage Plug 2 908198 


1 092019 74 Key - Liner 1 

2 182040 

20 Head 2 032039 76 Grease Fitting 2 317815 

21 Capscrews - Head 36 920532 76A Grease Relief Fitting 2 701992 


1 903172 77 Push Rod 3 

1 122005 

24A Locknut – Bearing 2 

2 903541 88 O-Ring - R/V Cap 1 

1 701926 


903542 Grease Seal – LGLD4(A) 2 


104 

385125 

Grease Seal – LGL4(A) 1 

1 331908 

27 

Bearing Cover – LGLD4(A) 2 186 Shaft Protector (LGLD4 Only) 1 341801 

041815 

Bearing Cover – Inboard, LGL4(A) 1 

Tool - Locknut 903092 

27A Bearing Cover – Outboard, LGL4(A) 1 041817 Kit - Maintenance 898922 

Kit - Rebuild 899022 


2 Included in Rebuild Kit Note 3 – See Table on other side for proper parts. 


- 78 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump models: lgld4a, lgl4a, lgl4, lgld4 (continued) 

MECHANICAL SEAL - STANDARD 

Ref. 

No. 

Part Name 

Parts 

Per 

Pump 

Part No. 


1 332050 

153A Stationary Seat (Hardened Steel) 2 ** 

153B Seal Face (Carbon) 2 ** 


153D O-Ring - Stationary (Buna-N) 2 701934 

153E O-Ring - Rotating (Buna-N) 2 711912 




Use the table below to determine the proper parts for each model. 

Ref. Part Name 

Parts Per LGLD4A and LGL4A Discontinued LGLD4 and LGL4 

No 

Pump Part No. Part No. 

2 Adjusting Screw - R/V 1 436310 436307 

3 Locknut - Adjusting Screw 1 432039 436355 

8 Spring - R/V 1 472039 476305 

12 Casing 1 012009 012000 

Use Dimension ‘A’ as shown in the drawing to determine the pump model number. 

The pump model number will also be shown on the nameplate. 

Model 

Dim ‘A’ 

LGLD4A, LGL4A 2.19 in. 5.56 cm. 

LGLD4, LGL4 1.75 in. 4.45 cm. 

H 

REF. 

NO. 

See 

Below 

HYDRAULIC MOTOR ADAPTER PARTS 

PART NAME 

Hydraulic Motor Adapter Kit 

PARTS 

PER 

PUMP 

* See 

Below 

PART 

NO. 

892037 

26A Gasket – Hydraulic Motor Adapter 1 381817 

28A Capscrew – 

Hydraulic Motor Adapter / Head 

34 

Coupling w/ Setscrew – 

1.25” straight key hyd. motor shaft 

6 920369 

1 906970 

35 Key – Coupling 1 909184 



135 

Hydraulic Motor Adapter – 

SAE A Flange 

1 041829 

135A Capscrew – Adapter / Motor 2 920510 

* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were a two 

piece design – refer to page 206-C00. 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 79 -

lackmer pump parts 


PUMP MODEL: TLGLF3C 

See Instructions 501-D00 for Installation, Operation and Maintenance 

LOCKNUT TOOL 

H 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

4 Cover - Relief Valve (R/V) 1 415108 O-Ring – Flange 2 1/2” x 2 3/4” 2 

701919 

42A 

5 Capscrew - R/V Cover 6 920331 O-Ring – Flange 2 5/8” x 2 7/8” 2 1,3 702004 

8 Spring - R/V 1 

4 471428 42B Capscrew - Flange, Flanged Elbow 8 920491 

9 Valve - R/V 1 

4 451417 71 Disc 2 

1 065121 


1 701919 72 O-Ring - Head 2 

1 711923 

12 Casing 1 015128 73 Gage Plug 2 908198 

13 Rotor & Shaft Assembly 5 1 

2 265147 74 Key - Liner 1 

2 185193 

14 Vane - Duravane 6 

1 095132 76 Grease Fitting 2 317815 

20 Head 2 035132 76A Grease Relief Fitting 2 701992 

21 Capscrews - Head 36 920351 77 Push Rod 3 

1 121607 


1 903156 104 Grease Seal 2 

1 331918 


2 903521 123 Dirt Shield 2 

1 701480 


1 903522 186 Shaft Protector 1 341601 


1 383940 — Tool - Locknut 903091 

27 Bearing Cover 2 041431 — Kit – Maintenance — 898980 

28 Capscrews - Bearing Cover 8 920285 — Kit – Maintenance with R/V — 899225 

35 Key - Shaft 1 

1 909130 — Kit – Rebuild — 899080 

41 Liner 1 

2 185101 — Kit – Rebuild with R/V — 899125 

Flange - 2" NPT 652010 

42 Flange - 2" Weld 1-2 652024 

Flanged Elbow - 2" NPT 655100 

Flanged Elbow - 2" Weld 655109 




3 Larger O-Ring introduced October 2002 

4 Additional parts Included in Kits with R/V 

5 Includes Ref. No. 24A & 24B 

- 80 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump Model: tlglf3c (continued) 

H 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 81 -


Discontinued Models BLACKMER PARTS LIST 

Parts availibility may 

PUMP MODEL: TLGLF4A 

be limited. 

DISCONTINUED MODEL: TLGLF4 


LOCKNUT 

TOOL 

H 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

TLGLF4A 

Part No. 

TLGLF4 

Part No. 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

TLGLF4A 

Part No. 

TLGLF4 

Part No. 

1 Cap - Relief Valve (R/V) 1 413952 413952 42A O-Ring - Flange 1 701937 701937 

2 Adjusting Screw - R/V 1 436310 436307 42B Capscrew - 3" NPT Flange 4 920663 920663 

3 Locknut - Adjusting Screw 1 432039 436355 Capscrew - 3", 4" 920640 920640 

4 Cover - R/V 1 412001 412001 Weld Flange; Blank Flange 

5 Capscrews - R/V Cover 4 920663 920663 TWIN DISCHARGE PORT OPTIONS 

7 Spring Guide - R/V 1 426355 426355 43 Flange - 2" NPT 2 652010 652010 

8 Spring - R/V 1 472039 472039 Flange - 2" Weld 652024 652024 

9 Valve - R/V 1 452001 452001 43A O-Ring - 2" Flange 2 1 / 2” x 2 3 / 4” 2 

1 701919 701919 


1 701946 701946 O-Ring - 2" Flange 2 5 / 8” x 2 7 / 8” 2 

1,3 702004 702004 

12 Casing 1 012039 012039 43B Capscrew - Discharge Flange 8 920491 920491 

13 Rotor & Shaft Asy. 1 

2 262024 262022 71 Disc 2 

1 062039 062039 

(includes Ref. No. 24A & 248) 71A Machine Screw - Disc 8 

2 920015 920015 


1 092019 092019 71B Lockwasher - Machine Screw 8 

2 909634 909634 

20 Head 2 032039 032039 72 O-Ring - Head 2 

1 702039 702039 

21 Capscrews - Head 36 920532 920532 73 Gage Plug 2 908198 908198 


1 903172 903172 74 Key - Liner 1 

2 182040 182040 


2 903541 903523 76 Grease Fitting 2 317815 317815 


1 903542 903524 76A Grease Relief Fitting 2 701992 701992 


1 385125 385125 77 Push Rod 3 

1 122005 122001 

27 Bearing Cover 2 041815 041815 88 O-Ring - R/V Cap 1 

1 701926 701926 

28 Capscrews - Bearing Cover 12 920286 920286 104 Grease Seal 2 

1 331908 331908 


1 909183 909183 186 Shaft, Protector 1 341801 341801 

41 Liner 1 

2 182000 182039 Tool - Locknut 903092 903091 

AUXILIARY INTAKE OPTIONS Kit - Maintenance 898922 N/A 

42 Flange - 3" NPT 1 652012 652012 Kit - Rebuild 899022 N/A 

Flange - 4" Weld 652005 652005 

Flange - 3" Weld 652007 652007 

Flange - Blank 652000 652000 



3 Larger O-Ring introduced October 2002 

Keep this parts list with Installation, Operation and 

Maintenance Instructions 

- 82 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump model: tlglf4a, tlglf4 (continued) 


Ref. 

Parts Per 

Part Name 

No. 

Pump 

Part No. 


1 332050 







** NOTE: Mechanical Seal Assy. (Ref. 153) is only sold as a complete assembly. 


TLGLF4 

TLGLF4A 

Part Name 

Interchangeability status w/TLGLF4A 

Interchangeability status w/TLGLF4 

PART NO. REF. PART NO. REF. 

Push Rods 122001 c 

1 122005 c 

Liner 182039 c 

2 182000 b 

Rotor & Shaft 262022 c 

2 262024 a 

Bearing Locknut 903523 c 

2 903541 c 

Bearing Lockwasher 903524 c 

1 903542 c 



Reference: 

a = Interchangeable, but requires new Bearing Locknuts PN 903541 and Bearing Lockwasher PN 903542. 

These are included whe ordering Rotor & Shaft PN 262024. 

b = Interchangeable but requires new push rods PN 122005. 

c = Not Interchangeable 

H 


Parts 

Ref. 

Part Name 

Per Part No. 

No. 

Pump 

See 

Below 


* See 

Below 

892037 


28A 

34 

Capscrew – 




6 920369 

1 906970 




135 


SAE A Flange 

1 041829 


* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two 


CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 83 -



PUMP MODEL: TLGLF4B 


LOCKNUT 

TOOL 

H 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

Ref. 

No. 

Description 

Parts 

Per 

Pump 

Part No. 

1 Cap - Relief Valve (R/V) 1 413952 42A O-Ring - Flange 1 701937 

2 Adjusting Screw - R/V 1 436310 42B Capscrew - 3" NPT Flange 4 920663 

3 Locknut - Adjusting Screw 1 432039 Capscrew - 3", 4" 920640 

4 Cover - R/V 1 412001 Weld Flange; Blank Flange 

5 Capscrews - R/V Cover 4 920663 TWIN DISCHARGE PORT OPTIONS 

7 Spring Guide - R/V 1 426355 43 Flange - 2" NPT 2 652010 

8 Spring - R/V 1 472039 Flange - 2" Weld 652024 

9 Valve - R/V 1 452001 43A O-Ring - 2" NPT Flange 0 - 2 

1 701919 


1 701946 O-Ring - 2" Weld Flange 0 - 2 

1 702004 

12 Casing 1 012041 43B Capscrew - Discharge Flange 8 920491 

13 Rotor & Shaft Asy. 1 

2 262041 71 Disc 2 

1 062039 

(includes Ref. No. 24A & 24B) 71A Machine Screw - Disc 8 

2 920015 


1 092019 71B Lockwasher - Machine Screw 8 

2 909634 

20 Head 2 032041 72 O-Ring - Head 2 

1 702039 

21 Capscrews - Head 28 920532 73 Gage Plug 2 908198 


1 903166 74 Key - Liner 1 

2 182040 


2 903541 76 Grease Fitting 2 317815 




1 385125 77 Push Rod 3 

1 122009 

27 Bearing Cover 2 041815 88 O-Ring - R/V Cap 1 

1 701926 

28 Capscrews - Bearing Cover 12 920286 104 Grease Seal 2 

1 331908 


1 909183 186 Shaft, Protector 1 341801 

41 Liner 1 

2 182000 Tool - Locknut 903092 

AUXILIARY INTAKE OPTIONS Kit – Maintenance 899224 

42 Flange - 3" NPT 1 652012 Kit – Rebuild 899124 

Flange - 4" Weld 652005 

Flange - 3" Weld 652007 

Flange - Blank 652000 



Keep this parts list with Installation, Operation and 

Maintenance Instructions 

- 84 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293


Pump model : tlglf4b (continued) 


Ref. 

Parts Per 

Part Name 

No. 

Pump 

Part No. 


1 332050 







** NOTE: Mechanical Seal Assy. (Ref. 153) is only sold as a complete assembly. 


TLGLF4 

TLGLF4A 

Part Name 

Interchangeability status w/TLGLF4A 

Interchangeability status w/TLGLF4 

PART NO. REF. PART NO. REF. 

Push Rods 122001 c 

1 122005 c 

Liner 182039 c 

2 182000 b 

Rotor & Shaft 262022 c 

2 262024 a 

Bearing Locknut 903523 c 

2 903541 c 

Bearing Lockwasher 903524 c 

1 903542 c 



Reference: 

a = Interchangeable, but requires new Bearing Locknuts PN 903541 and Bearing Lockwasher PN 903542. 

These are included whe ordering Rotor & Shaft PN 262024. 

b = Interchangeable but requires new push rods PN 122005. 

c = Not Interchangeable 

H 


Parts 

Ref. 

Part Name 

Per Part No. 

No. 

Pump 

See 

Below 


* See 

Below 

892037 


28A 

34 

Capscrew – 




6 920369 

1 906970 




135 


SAE A Flange 

1 041829 


* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two 


CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 85 -

Compressors/motors 

Compressors, Hydraulic Drive, Motors, Starters 

H 

COMPRESSORS 

Blackmer Oil-Free 

Compressors 

Blackmer offers a variety of factory 

assembled compressor packages to fit 

most application requirements. Standard 

base mounted units are available in a 

variety of styles. 

Item # Approx. Liquid Transfer Rate Motor Size 

LB161 90 GPM @ 780 RPM 7.5 HP 

LB361 194 GPM @ 780 RPM 15 HP 

LB601 351 GPM @ 790 RPM 25 HP 

LB942 640 GPM @ 750 RPM 40 HP 

Portable Liquid 

transfer, vapor 

recovery systems from 

blackmer 

Custom skid mounted compressor units 

offer flexibility for transferring liquids 

in remote locations or emergency 

situations. 

These units are customized to fit your 

specific needs. 

Krug Vapor Compressors 

• Has LP Gas fueled engine (uses LP 

being transferred as fuel) 

• 20 GPM transfer rate 

• 1/2” FNPT connections 

Item # 

K-VP-LP 

K-VP-HK 

k25459B 

K209870 

K3X927 

Krug Hand Pump 

Operates on the simple principle of the 

automotive piston. Used for filling 20# 

cylinders, lift truck cylinders, etc. 

Inlet: 1” FNPT 

Outlet: 3/4” FNPT 

Capacity: 6 GPM at 40 strokes/min. 

Item # 

KHP 

K-HP-HK 

Description 

Compressor with LP engine 

Connecting hose kit 

Replacement Compressor 

3/4” replacement clutch 

Replacement pulley 

Description 

Hand pump 

Connecting hose kit 

MOTORS/STARTERS/SWITCHES 

Explosion Proof Motors 

Class 1, Group D (60 cycle), 1750 rmp 

Item # HP Phase Voltage 

AXPD010C1B* 1 1 115/230 

AXPD015C1B* 1 1/2 1 115/230 

AXP015C3B* 1 1/2 3 230/460 

AXP020T3B 2 3 230/460 

AXPB03T1B 3 1 230 

AXP030T3B 3 3 230/460 

AXPD05T1B 5 1 230 

AXP050T3B 5 3 230/460 

AXP075T3B 7 1/2 3 230/460 

AXP100T3B 10 3 230/460 

AXP150T3B 15 3 230/460 

AXP250T3B 25 3 230/460 

*C-Face Mount 

Lovejoy Couplings 

0300010 - 7/8” L095 

0300020 - 1 1/8” L095 

0300060 - spider for L095 

Explosion Proof 

STARTERS 

Class 1, Group D (60 cycle) 

NEMA Type 3R, 7, & 9 

Magnetic Starters 

are designed for full voltage starting 

of motors. All Bulletin 509 starters are 

equipped with manual reset overload 

relays and may be operated by remote 

push button control. Protects motor from 

thermal overload and undervoltage. 

Push button in cover. 

Item # Size Voltage Phase Max HP 

B509BHXD-1 1 115 1 2 

B509BHXA-1 1 230 1 3 

B509XHXD-1 1P 115 1 3 

B509XHXA-1 1P 230 1 5 

B509BHA-1 1 230 3 71/2 

B509BHB-1 1 460 3 10 

B509CHA-1 2 230 3 15 

B509CHB-1 2 460 3 25 

KECF212 

Explosion proof 

Flexible connector 

For connecting wiring to motor on 

a pump unit so motor can be adjusted 

3/4” x 12” 

- 86 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293

Manual Starters, Liquid & Vapor Meters 

STARTERS/SWITCHES (continued) 

METERS 

Manual Starters 

Designed for use where remote control 

is not required and where undervoltage 

protection is not needed. The motor is 

started at full line voltage. Thermal type 

overload protection is provided. START/ 

STOP push buttons in cover. 

Item # Size Voltage Phase Max HP 

115V 230V 460V 

B609AHX 0 115/230 1 1 2 -- 

B609BHX 1 115/230 1 2 3 -- 

B609XHX 1P 115/230 1 3 5 -- 

B609AHW 0 230/460 3 -- 3 5 

B609BHW 1 230/460 3 -- 7 1/2 10 

Class 1, Group D (60 Cycle) NEMA Type 3R, 7 and 9 

B800H-2HA7 

Remote Push Button 

Station 

Provides remote operation of magnetic 

starters 

Class 1, Group D (60 Cycle) NEMA Type 

3R, 7 and 9 

KXS52C OFF/ON SWITCH 

For use with 1 and 1-1/2 HP explosion 

proof motors. 

Class 1, Group D (60 Cycle) NEMA 

Type 3R, 7 and 9 

K1222 

Toggle switch only for KXS52C. 

E4000 - Neptune 

Electronic register 

Replace your Bobtail’s Neptune or 

Veeder-Root mechanical register with 

this easy to use electronic register. 

• To install an E4000 on a 1 1/2” Neptune meter, use a 201072-001 

1 1/2” adaptor plate. 

• To install an E4000 on a LC meter, 

you need: 

1000678 Kit 

LC499988 Strainer cover 

LC81256 Thermowell 

LC06854 O-ring 

epson slip printer 

tm-u295-071 

STARTERS/METERS 

meters (continued) 

90028-101 

1” Liquid propane meter 

Designed for metering small quantities of 

liquid propane into portable containers 

and engine fuel tanks. Complete with 

strainer, vapor eliminator, & differential 

valves. 

Flow Range: 3 to 18 gpm. 

Veeder-root printing 

register 

Replace your Neptune register with a 

long lasting Veeder-Root Register 

ITEM# 

DESCRIPTION 

L789002-002 Printing Register 

L886201-001 Adaptor to fit 1 1/4” to 2” Neptune without ATC 

L886205-001 Adaptor to fit 1 1/4” to 2” Neptune with ATC 

METER SEALS 

833-ORM 

Remanufactured 

Schlumberger/Neptune 

833 printer register 

1 Year or 1 Million Gallon warranty 

(whichever comes first). Rebuilt 833 

registers provide you with the same quality 

measurement and reliability that you have 

grown accustom to! 

Totally rebuilt, reconditioned and 

repainted units. All parts are inspected 

and any defect will be completely 

corrected. 

M250TC Metris Vapor Meter 

This 3/4” meter will meter 400,000 BTU 

at 11” W.C. and up to 1,200,000 BTU of 

5 psig inlet pressure (max.). It has a direct 

read CFU index. 3/4” connections. Larger 

sizes are available. 

Item # Description 

163-057-510 18” Seal Wire 

163-057-510S 18” Seal Wire with lead seals 

Neptune coriolis mass 

flow liquid meters 

For bulk plants and bobtails. The Coriolis 

reduces LP Gas under-measurement, and 

compared to traditional mechanical 

flow meters, the Coriolis offers better 

accuracy with higher flow rates over a 

longer service life. When combined with 

the Neptune E4000 Register, the Coriolis 

allows an upgrade path not obtainable 

with competitive electronic transaction 

management systems. Features electronic 

temperature compensation and the 

availability of combining with hand helds. 

Available in sizes from 12 - 70 GPM. 

H 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293 

- 87 -

METER PARTS 

Neptune & Liquatech Meter Parts 

neptune/liqua-tech meter parts 

Description Part # 

3/4” and 1” Meter 3/4” 1” 

Gasket, Main Case L4861-016 L4861-016 

Measuring Chamber, Complete L42075-101 L42075-101 

Gasket, O-Ring, Vapor Release Cover L100139-012 L100139-012 

Strainer Assembly L100683-001 L100683-001 

Seal, Differential Valve, U-Cup L100025-008 L100025-008 

O-Ring, Inlet/Outlet, Differential Valve L100139-007 L100139-007 

Differential Valve Repair Kit L100028-011 L100028-011 

1 1/4”, 1 1/2”, and 2” Meter 1 1/4” 1 1/2” 2” 

Stud, Register Mounting L84435-000 L84435-000 L84435-000 

Gasket, Main Case L4862-008 L4862-008 L84806-000 

Measuring Chamber, Complete L43260-101 L83271-101 L45806-101 

Star Connection L82976-001 L82976-001 L82976-001 

Gear Train, Complete L83501-000 L84981-000 L83502-000 

Seal, U-Cup Shaft L100025-002 L100025-002 L100025-002 

H 

Vapor Release and Strainer 1 1/2” 2” 

Gasket, O-Ring. Vapor Release Cover L100139-022 L100139-022 

Main Valve, Complete L89274-006 L89274-006 

Piston, Seal L83179-000 L83179-000 

Float, Complete L82476-001 L82476-001 

Strainer and Gasket Assembly L101433-704 

Strainer, Inner and Outer Combo L101462-003 

Inlet Check Valve, Complete L84983-704 L84813-702 

Gasket, O-Ring, Strainer Cover L100139-010 L84818-000 

Differential Valve 1 1/2” 2” 

Diaphragm L83771-002 L83771-002 

O-Ring L100139-001 L100139-001 

Gasket, Flange L82060-000 L84818-000 

Temperature Compensator 1 1/4” 1 1/2” 2” 

Gear Train, Complete L83501-000 L84981-000 L83502-000 

Seal, U-Cup Shaft L100025-002 L100025-002 L100025-002 

Adapter Unit, Complete L86602-005 L86602-005 L86602-005 

Stud, Regoster Mounting L84435-000 L84435-000 L84435-000 

Rollpin L100370-003 L100370-003 L100370-003 

Drive Fork L84192-006 L84192-006 L84192-006 

Neptune Registers 

Part# 

600 Series Register (for 3/4” meter) 100498-009 

833 Printer Register 880030-000 

601 Series Register (for 1” meter) 100498-016 

- 88 - 

CONYERS, GA (800) 241-5652 

APOPKA, FL (800) 432-1869 

GOLDSBORO, NC (800) 426-9293

PuMPING SYSTEMS - Rutherford Equipment, Inc.

Create successful ePaper yourself

Delete template?

Save as template?