USB Serial Adapter – Model INTUSB485-1 - Banner Engineering
USB Serial Adapter – Model INTUSB485-1 - Banner Engineering
USB Serial Adapter – Model INTUSB485-1 - Banner Engineering
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>USB</strong> <strong>Serial</strong> <strong>Adapter</strong> <strong>–</strong> <strong>Model</strong> INT<strong>USB</strong>485-1<br />
<strong>Adapter</strong> for EZ-ARRAY ® 5-pin Communications Cable to PC <strong>USB</strong> Port<br />
Features<br />
• Easy-to-use <strong>USB</strong>-to-485 adapter connects to a <strong>USB</strong> port on a computer or <strong>USB</strong> hub.<br />
• Easy plug-and-play and hot plug features simplify connection of an RS-422 or RS-485<br />
serial device.<br />
Overview<br />
When plugged into the <strong>USB</strong> port, the <strong>USB</strong> industrial I/O adapter is automatically detected<br />
and installed. There are no IRQ or COM port conflicts, since the port requires no<br />
additional IRQ, DMA or memory. The adapter’s RS-422/485 port functions as a native<br />
Windows COM port, and it is compatible with Windows serial communication applications.<br />
Each port is individually configurable. The INT<strong>USB</strong>485-1 is powered via the <strong>USB</strong><br />
interface; no additional power supply is needed.<br />
When using the PC-based EZ-ARRAY Control Software to configure the EZ-ARRAY, the<br />
INT<strong>USB</strong>485-1 provides a quick solution to convert from a universal serial bus interface to<br />
the EZ-ARRAY RS-485 interface.<br />
Simply connect the EZ-ARRAY cable (model MQDMC-5..) to the terminal strip to<br />
configure the EZ-ARRAY receiver (refer to the EZ-ARRAY Users Manual p/n 130426 for<br />
configuration information). Included with the INT<strong>USB</strong>485-1 is the <strong>USB</strong> cable and supplied<br />
software to connect with the PC. A four-position DIP switch on the external housing must<br />
be set as shown in Figure 1 (default positions), and eight jumpers inside the housing must<br />
be configured as shown in Figure 2.<br />
Switch Setting<br />
S1 ON<br />
S2 OFF<br />
S3 OFF<br />
S4 OFF<br />
Figure 1. DIP-switch positions for use with EZ-ARRAY<br />
Do Not Jumper J1 Jumper Pins 1-2, 3-4, 5-6<br />
Do Not Jumper Pins 7-8, 9-10, 11-12, 13-14<br />
Figure 2. Internal jumper positions for use with EZ-ARRAY<br />
Printed in USA 11/06 P/N 130144
<strong>USB</strong> <strong>Serial</strong> <strong>Adapter</strong> <strong>–</strong> <strong>Model</strong> INT<strong>USB</strong>485-1<br />
Environmental Rating IEC IP10, NEMA 1<br />
Operating Conditions Temperature: 0° to +50° C (+32° to 121° F)<br />
Max. Relative Humidity: 90% at 50° C (non-condensing)<br />
Certifications<br />
WARRANTY: <strong>Banner</strong> <strong>Engineering</strong> Corp. warrants its products to be free from defects for one year. <strong>Banner</strong> <strong>Engineering</strong> Corp. will repair or replace,<br />
free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty<br />
does not cover damage or liability for the improper application of <strong>Banner</strong> products. This warranty is in lieu of any other warranty either expressed or<br />
implied.<br />
P/N 130144<br />
72.5 mm<br />
(2.85")<br />
36.0 mm<br />
(1.42")<br />
Dimensions<br />
70.0 mm<br />
(2.75")<br />
82.0 mm<br />
(3.23")<br />
Specifications<br />
77.5 mm<br />
(3.05")<br />
<strong>Banner</strong> <strong>Engineering</strong> Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com<br />
22.5 mm<br />
(0.88")<br />
Terminal<br />
Block<br />
Hookup<br />
6<br />
5<br />
4<br />
3<br />
2<br />
1<br />
bu<br />
wh<br />
bk<br />
Common<br />
N.C.<br />
N.C.<br />
N.C.<br />
D1 / B / +<br />
D0 / A / <strong>–</strong><br />
Connection of MQDMC-5.. cable to adapter terminal block