Instruction Manual - Team Associated

More documents

Recommendations

Info

26 :: Shocks Build (cont.) - Bag G Step 1-3 Shock fluid 30wt #5422 Step 3-4 Shock fluid 30wt #5422 Step 5-6 6441 Shock cap (molded) Step 7 * Shock Bleeding Steps: 1. Pull shock shaft down. 2. Fill shock body 3/4 full with silicone fluid. 3. Slowly move the shock shaft up and down to remove air from under piston. 4. Wait for bubbles to come to surface. 5. Fill shock body to top with silicone fluid. 6. Place several drops of oil in the cap and on cap threads. 7. Install cap and tighten completely. 8. Slowly compress shaft all the way to the top. If there is pressure at the top of the stroke, there is too much oil or air. You must bleed it out. 9. Slowly pull shaft down. 10. Unscrew the cap 3/4 turn and tilt the shock at a slight angle. 11. Slowly compress the shaft to push out excess oil and air. You should see bubbles coming out from under the cap. 12. With the shaft compressed, tighten the cap and re-check for pressure at the top of the stroke. If there is still pressure, repeat steps 9 thru11. :: Shocks Build (cont.) - Bag G 6475 Spring collar 7425 Front spring (gold) 3.70lb 8846 Preload spacers x1 x1 6475 Spring cup 6475 Spring collar 6480 Rear spring (green) 1.90lb 8846 Preload spacers x1 x1 x1 6475 Spring cup Front Shock Rear .12 .03 .25 .25 .06 Shock :: Shocks Build (cont.) - Bag G 3 2 1 6473 Shock bushings 6472 Shock mounting nut OII Front Shock 6925 4-40 x 1/2 shcs Build left and right sides!
27 :: Shocks Build (cont.) - Bag G 6473 Shock bushings 6472 Shock mounting nut 3 2 1 O I Rear Shock 6925 4-40 x 1/2 shcs Build left and right sides! :: Wheel and Tire Assembly 91101 KMC Hex Wheel (black) 91101 KMC Hex Wheel (black) 89413 1/8th molded tire insert 89413 1/8th molded tire insert ! Note: Clean the rims and tire bead where the two will mount to each other before you glue them together. You can clean them with either rubbing alchohol, or r/c electric motor spray. Place the foam insert inside the tire. Install the tire on the rim, and push the tire beads inside the groves on the rim. Use Tire glue #1597 to glue the tire to the wheel. Glue one side at a time, allowing enough time for the glue to dry before continuing to the other side. Tip: You can use a rubber band to hold the tire tight against the wheel while the glue is drying. ! Build 2 Front! ! Tire glue is not included! 9809 SC10 Tire w/foam insert JConcepts #3042 JConcepts subculture tire, green compound (use on rear) ! Build 2 Rear! The rear tires included in this RTR are made by JConcepts. JConcepts tires can be purchased at their website: http://www.jconcepts.net
Page 1 and 2: 4/12
Page 3 and 4: 3 :: Table of Contents 1...........
Page 5 and 6: 5 :: Steering Build (cont.) - Bag A
Page 7 and 8: 7 :: Front Shock Tower/Bumper Build
Page 9 and 10: :: Ball Differential Build - Bag B
Page 11 and 12: 11 :: Gearbox Build (cont.) - Bag B
Page 13 and 14: 13 :: Rear Shock Tower Build (cont.
Page 15 and 16: 15 :: Rear Suspension Build (cont.)
Page 17 and 18: 17 :: Radio Tray Build (cont.) - Ba
Page 19 and 20: 19 :: Radio Tray Build (cont.) - Ba
Page 21 and 22: 21 :: Engine Build - Bag F Nitro En
Page 23 and 24: 23 :: Engine Build (cont.) - Bag F
Page 25: 25 :: Shocks Build - Bag G Front Sh
Page 29 and 30: 29 :: Tuning Tips Tips for Beginner
Page 31 and 32: 31 :: Shocks 5407 6299 6441 6458 64
Page 33 and 34: 33 :: Front Bulkhead 4334 6915 6922
Page 35 and 36: 35 :: Slipper 6629 7485 7486 7953 7
Page 37 and 38: 37 :: Engine / Clutch / Air Filter
Page 39 and 40: 39 :: Factory Team and Option Parts
Page 41 and 42: 41 :: 1/18 Kits and RTR’s 20103 2
Page 43 and 44: Front Suspension 2 3 1 Driver: SC10
Page 45 and 46: Front Suspension Setup Sheet Driver

Instruction Manual - Team Associated

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?