Download manual - Systema Polska Sp. z o.o.
Download manual - Systema Polska Sp. z o.o. Download manual - Systema Polska Sp. z o.o.
SYSTEMA S.p.A. 3 INSTRUCTIONS FOR INSTALLERS 3.1 Technical Reference Standards and Legislation 3.3 Luoghi d’installazione e distanze di sicurezza. Airtight gas convectors EEC Directive 90/396 CEE regarding combustible gas-fired devices and their accessories; EC seal of Approval. We recommend observing the following rules in order to obtain the maximum convector output efficiency: - Position the device while bearing in mind the priority areas to be heated, the absorption walls (windows, doors, French windows etc.), and the existence of shelves and other obstacles that might compromise the circulation of the hot air released by the radiator above and the effect of the heat radiated from the front panel. - If more than one device must be installed in the same room, we recommend staggered and opposing positioning in order to provide the entire area with uniform coverage. - The devices must never be installed in recessed niches or positions that do not ensure sufficient aeration for good operation. - Install the devices along perimetral walls whenever possible. - Observe the following rules to simplify interventions on the radiator or the removal of the shell: Draw 15 a) the distance of the device from the floor must never be less than 10 cm.; b) any shelves installed above the radiator must be positioned at least 10 cm higher; c) a minimum distance of 10 cm from the wall must be respected whenever devices are installed in recessed niches; - avoid positioning furnishings above the shell. Installation must be performed only by qualified professionals in complete respect of the safety regulations in force. The Manufacturer declines all liability for erroneous installation or the inappropriate or incorrect use of the device. Rev. 05IT0112-1 20
Airtight gas convectors SYSTEMA S.p.A. 3.4 Device installation Observe the instructions provided in the following pages for the assembly of the device. 1) Position the assembly frame on the wall and fasten it in place using adhesive tape at a minimum distance of 10 cm from the floor perfectly squared (See Draw 16). Trace and drill the hole required for flue gas expulsion with a 2% inclination towards the outside of the wall if possible (See Draw 16). 2) Position the assembly frame perfectly squared once again, making sure that the flue gas expulsion hole is perfectly centered and then drill no. 4 holes with 8 mm diameter and insert the screw anchor provided. Draw16 Dima di montaggio 3) After drilling the hole, measure the thickness of the wall “M”, cut the suction pipe (8) with the same thickness of the wall. Cut the flue gas expulsion pipe (6), making sure to add the value listed in the table to the length of the pipe (8) cut above (See Draw117-18). 21 Rev. 05IT0112-1
- Page 1 and 2: AIRTIGHT GAS CONVECTORS Pilot flame
- Page 3 and 4: Airtight gas convectors Summary SYS
- Page 5 and 6: Airtight gas convectors 1 GENERAL R
- Page 7 and 8: Airtight gas convectors CONTROL UNI
- Page 9 and 10: Airtight gas convectors 2.6 Electro
- Page 11 and 12: Airtight gas convectors 2.8 Explode
- Page 13 and 14: Airtight gas convectors SYSTEMA S.p
- Page 15 and 16: Airtight gas convectors SYSTEMA S.p
- Page 17 and 18: Airtight gas convectors Series E wi
- Page 19: Airtight gas convectors Series FE w
- Page 23 and 24: Airtight gas convectors SYSTEMA S.p
- Page 25 and 26: Airtight gas convectors 3.4 Specifi
- Page 27 and 28: Airtight gas convectors 3.5 Gas lin
- Page 29 and 30: Airtight gas convectors SYSTEMA S.p
- Page 31 and 32: Airtight gas convectors SYSTEMA S.p
- Page 33 and 34: Airtight gas convectors SYSTEMA S.p
- Page 35 and 36: Airtight gas convectors SYSTEMA S.p
- Page 37 and 38: Airtight gas convectors 4 INSTRUCTI
- Page 39 and 40: Airtight gas convectors 5 PUTTING T
- Page 41 and 42: Airtight gas convectors SYSTEMA S.p
- Page 43: Airtight gas convectors SYSTEMA S.p
Airtight gas convectors<br />
SYSTEMA S.p.A.<br />
3.4 Device installation<br />
Observe the instructions provided in the following pages for the assembly of the device.<br />
1) Position the assembly frame on the wall and fasten it in place using adhesive tape at a<br />
minimum distance of 10 cm from the floor perfectly squared (See Draw 16). Trace and<br />
drill the hole required for flue gas expulsion with a 2% inclination towards the outside of the<br />
wall if possible (See Draw 16).<br />
2) Position the assembly frame perfectly squared once again, making sure that the flue gas<br />
expulsion hole is perfectly centered and then drill no. 4 holes with 8 mm diameter and<br />
insert the screw anchor provided.<br />
Draw16 Dima di montaggio<br />
3) After drilling the hole, measure the thickness of the wall “M”, cut the suction pipe (8) with<br />
the same thickness of the wall. Cut the flue gas expulsion pipe (6), making sure to add the<br />
value listed in the table to the length of the pipe (8) cut above (See Draw117-18).<br />
21<br />
Rev. 05IT0112-1