User Manual - Etilize

More documents

Recommendations

Info

4. If you are instructed to return the hot-swap power supply, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. 5. Touch the static-protective package that contains the hot-swap power supply to any unpainted metal surface on the server; then, remove the power supply from the package and place it on a static-protective surface. 6. Place the power supply into the bay guides. 7. Press down on the orange release lever and push the power supply toward the front of the chassis until it locks into place. 8. Connect one end of the power cord into the connector on the back of the power supply and connect the other end of the power cord into a properly grounded electrical outlet. 9. Make sure that both the ac and dc power LEDs on the rear of the power supply are lit, indicating that the power supply is operating correctly. Go to “Completing the installation” on page 62 for information about completing the installation. 60 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide
Installing a security rope clip To help prevent hardware theft, you can add a security rope clip and cable to the server. After you add the security cable, make sure that it does not interfere with other cables that are connected to the server. Before you begin, obtain the following items: v A flat-blade screwdriver v An adjustable wrench v A 19 mm (0.75 in.) rope clip or wire rope (similar to National Manufacturing number 3230, stock number 176-735) v Threaded nuts that fit the rope clip v A security cable v A lock, such as a combination lock or padlock To install a rope clip, complete the following steps: 1. Turn off the server and all attached devices. Disconnect all external cables and power cords. 2. Use a screwdriver to remove the two metal knockouts. 3. Insert the rope clip through the rear panel; then, attach and tighten the nuts. Rope clip 4. Thread the cable through the rope clip and around an object that is not part of or permanently secured to the building structure or foundation, and from which the cable cannot be removed. Fasten the cable ends together with a lock. After you add the security cable, make sure that it does not interfere with other cables that are connected to the server. Chapter 2. Installing optional devices 61
Page 1:
System x3200 M3 Types 7327 and 7328
Page 4 and 5:
Note: Before using this information
Page 6 and 7:
Connecting external devices . . . .
Page 8 and 9:
vi System x3200 M3 Types 7327 and 7
Page 10 and 11:
Important: All caution and danger s
Page 12 and 13:
Statement 2: CAUTION: When replacin
Page 14 and 15:
Statement 4: ≥ 18 kg (39.7 lb)
Page 16 and 17:
Statement 13: DANGER Overloading a
Page 18 and 19:
xvi System x3200 M3 Types 7327 and
Page 20 and 21:
The following illustration shows th
Page 22 and 23:
Note: The illustrations in this doc
Page 24 and 25:
v If Autostart is enabled, insert t
Page 26 and 27:
Table 1. Features and specification
Page 28 and 29: What your server offers The server
Page 30 and 31: Computing Group (TCG) specification
Page 32 and 33: IBM Systems Director v Memory chang
Page 34 and 35: The following is an illustration of
Page 36 and 37: Hard disk drive activity LED Power-
Page 38 and 39: Rear view The following illustratio
Page 40 and 41: v If a power failure occurs while t
Page 42 and 43: System-board internal connectors Th
Page 44 and 45: System-board switches and jumpers T
Page 46 and 47: System-board external connectors Th
Page 48 and 49: v Before you install optional hardw
Page 50 and 51: Removing the side cover Important:
Page 52 and 53: 6. Carefully pull the two bezel cli
Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
Page 56 and 57: v The following table lists the max
Page 58 and 59: Installing drives Depending on the
Page 60 and 61: DANGER Some laser products contain
Page 62 and 63: Drive retainer clip 10. Slide the d
Page 64 and 65: Server model with four hot-swap dri
Page 66 and 67: To install a simple-swap hard disk
Page 68 and 69: Installing an adapter The following
Page 70 and 71: 8. If you are installing a full-len
Page 72 and 73: Important: To ensure that any of yo
Page 74 and 75: Note: Before you continue, check al
Page 76 and 77: Installing the virtual media key To
Page 80 and 81: Completing the installation If you
Page 82 and 83: Reinstalling the side cover If you
Page 84 and 85: Connecting external devices Install
Page 86 and 87: Using the Setup utility The followi
Page 88 and 89: Select this choice to view or set t
Page 90 and 91: Passwords From the User Security me
Page 92 and 93: Starting the backup server firmware
Page 94 and 95: 2. The ServerGuide program stores i
Page 96 and 97: Note: Approximately 1 to 3 minutes
Page 98 and 99: 3. On the Welcome page, type a time
Page 100 and 101: In addition, you can download an LS
Page 102 and 103: Updating IBM Systems Director If yo
Page 104 and 105: Software service and support You ca
Page 106 and 107: Important notes Adobe and PostScrip
Page 108 and 109: Electronic emission notices 3039 E.
Page 110 and 111: IBM verändert bzw. wenn Erweiterun
Page 112 and 113: drive bay filler panel 41, 43 bay i
Page 114 and 115: password administrator 72 forgotten
Page 116: 98 System x3200 M3 Types 7327 and 7
show all

User Manual - Etilize

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?