User Manual - Etilize

More documents

Recommendations

Info

8. If you are installing a full-length adapter, remove the blue adapter guide (if any) from the end of the adapter. Adapter guide 9. Carefully grasp the adapter by the top edge or upper corners, and align it with the expansion slot guides; then, press the adapter firmly into the expansion slot. Move the adapter directly from the static-protective package to the expansion slot. Attention: Make sure that the adapter is correctly seated in the expansion slot before you turn on the server. Incomplete installation of an adapter might damage the system board or the adapter. 10. Install an expansion-slot screw at the rear of the adapter. 11. If you are installing a full-length adapter, press on the release lever on the right side of the front adapter-retention bracket to release the retaining tab on the left side of the bracket. 12. Connect required cables to the adapter. Route cables so that they do not block the flow of air from the fans. 13. Reinstall the rear adapter-retention bracket; then, rotate the bracket to the closed position. Note: If any adapters in the server are large or have heavy cables attached to them, you can remove the rear adapter-retention bracket and secure all of the adapters with expansion-slot screws. If you have other devices to install or remove, do so now; otherwise, go to “Completing the installation” on page 62. Installing the ServeRAID-BR10il v2 SAS/SATA controller The IBM ServeRAID-BR10il v2 SAS/SATA controller must be installed in its dedicated connector, PCI slot 1, on the system board. The ServeRAID-BR10il v2 adapter is supported on hot-swap server models only. The IBM ServeRAID-BR10il v2 SAS/SATA adapter enables integrated RAID levels 0, 1, and 1E capability on hot-swap hard disk drives. For configuration information, see the ServeRAID documentation at http://www.ibm.com/systems/support/. Attention: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. 52 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide
To install the ServeRAID-BR10il v2 adapter, complete the following steps: 1. Read the safety information beginning on page vii, and “Installation guidelines” on page 29. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. Remove the side cover (see “Removing the side cover” on page 32. Attention: To avoid breaking the retaining clips or damaging the ServeRAID-BR10il v2 adapter connector, open and close the clips gently. 3. Touch the static-protective package that contains the SAS/SATA controller to any unpainted surface on the outside of the server; then, remove the SAS/SATA controller from the package. 4. Position the SAS/SATA controller over the connector and the plastic standoff; then, press the SAS/SATA controller firmly into the connector and onto the plastic standoff. PCIe SAS slot ServeRaid-BR10il controller 5. Connect the signal cable to the SAS/SATA controller. 6. Replace the side cover (see “Reinstalling the side cover” on page 64). Go to “Completing the installation” on page 62. 7. Lock the side cover. 8. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server. If you have other devices to install or remove, do so now. Otherwise, go to “Completing the installation” on page 62. Installing the IBM ServeRAID-MR10i SAS/SATA controller The optional IBM ServeRAID-MR10i SAS/SATA controller can be installed in either PCI slot 1 or 2 on the system board. The ServeRAID-MR10i adapter is supported on hot-swap server models only. The IBM ServeRAID-MR10i SAS/SATA adapter enables integrated RAID levels 0, 1, 5, 6, and 10 support capability on hot-swap hard disk drives. For configuration information, see the documentation on the ServeRAID CD that comes with the adapter. Chapter 2. Installing optional devices 53
Page 1:
System x3200 M3 Types 7327 and 7328
Page 4 and 5:
Note: Before using this information
Page 6 and 7:
Connecting external devices . . . .
Page 8 and 9:
vi System x3200 M3 Types 7327 and 7
Page 10 and 11:
Important: All caution and danger s
Page 12 and 13:
Statement 2: CAUTION: When replacin
Page 14 and 15:
Statement 4: ≥ 18 kg (39.7 lb)
Page 16 and 17:
Statement 13: DANGER Overloading a
Page 18 and 19:
xvi System x3200 M3 Types 7327 and
Page 20 and 21: The following illustration shows th
Page 22 and 23: Note: The illustrations in this doc
Page 24 and 25: v If Autostart is enabled, insert t
Page 26 and 27: Table 1. Features and specification
Page 28 and 29: What your server offers The server
Page 30 and 31: Computing Group (TCG) specification
Page 32 and 33: IBM Systems Director v Memory chang
Page 34 and 35: The following is an illustration of
Page 36 and 37: Hard disk drive activity LED Power-
Page 38 and 39: Rear view The following illustratio
Page 40 and 41: v If a power failure occurs while t
Page 42 and 43: System-board internal connectors Th
Page 44 and 45: System-board switches and jumpers T
Page 46 and 47: System-board external connectors Th
Page 48 and 49: v Before you install optional hardw
Page 50 and 51: Removing the side cover Important:
Page 52 and 53: 6. Carefully pull the two bezel cli
Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
Page 56 and 57: v The following table lists the max
Page 58 and 59: Installing drives Depending on the
Page 60 and 61: DANGER Some laser products contain
Page 62 and 63: Drive retainer clip 10. Slide the d
Page 64 and 65: Server model with four hot-swap dri
Page 66 and 67: To install a simple-swap hard disk
Page 68 and 69: Installing an adapter The following
Page 72 and 73: Important: To ensure that any of yo
Page 74 and 75: Note: Before you continue, check al
Page 76 and 77: Installing the virtual media key To
Page 78 and 79: 4. If you are instructed to return
Page 80 and 81: Completing the installation If you
Page 82 and 83: Reinstalling the side cover If you
Page 84 and 85: Connecting external devices Install
Page 86 and 87: Using the Setup utility The followi
Page 88 and 89: Select this choice to view or set t
Page 90 and 91: Passwords From the User Security me
Page 92 and 93: Starting the backup server firmware
Page 94 and 95: 2. The ServerGuide program stores i
Page 96 and 97: Note: Approximately 1 to 3 minutes
Page 98 and 99: 3. On the Welcome page, type a time
Page 100 and 101: In addition, you can download an LS
Page 102 and 103: Updating IBM Systems Director If yo
Page 104 and 105: Software service and support You ca
Page 106 and 107: Important notes Adobe and PostScrip
Page 108 and 109: Electronic emission notices 3039 E.
Page 110 and 111: IBM verändert bzw. wenn Erweiterun
Page 112 and 113: drive bay filler panel 41, 43 bay i
Page 114 and 115: password administrator 72 forgotten
Page 116: 98 System x3200 M3 Types 7327 and 7
show all

User Manual - Etilize

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?