User Manual - Etilize
User Manual - Etilize User Manual - Etilize
DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following. Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Class 1 Laser Product Laser Klasse 1 Laser Klass 1 Luokan 1 Laserlaite Appareil A ` Laser de Classe 1 7. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 8. Set any jumpers or switches on the drive according to the documentation that comes with the drive. Note: You might find it easier to install the new drive from the front and then attach the cables. 9. Remove the drive retainer clip from the side of the drive cage of bay 1 or 2. Slide the drive retainer clip to the right to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive. Release buttons Drive retainer clip 10. If you are installing a 5.2-inch drive in bay 2, slide the drive into the bay. If you are installing a 3.5-inch drive in bay 2, you must attach the 5.2-inch. conversion kit to the 3.5-inch drive. Note: An optional diskette drive can be installed in bay 3. 42 System x3200 M3 Types 7327 and 7328: Installation and User’s Guide
11. Connect one end of the applicable signal cable into the rear of the drive and make sure that the other end of this cable is connected into the applicable SATA connector on the system board. 12. Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs). 13. If you have another drive to install or remove, do so now. 14. Connect the power cable to the rear of the drive. The connectors are keyed and can be inserted only one way. If you have other devices to install or remove, do so now; otherwise, go to “Completing the installation” on page 62. Installing an optional tape drive To install an optional tape drive, complete the following steps. 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Unlock the side cover. 4. Remove the side cover (see “Removing the side cover” on page 32). 5. Remove the two-piece bezel (see “Removing the two-piece bezel” on page 32). 6. Use a screwdriver to pry the filler panel and EMC shield away from the server. 7. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 8. Set any jumpers or switches on the drive according to the documentation that comes with the drive. 9. Remove the drive retainer clip from the side of the drive cage of bay 1 or 2. Slide the drive retainer clip to the right to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive. Chapter 2. Installing optional devices 43
- Page 10 and 11: Important: All caution and danger s
- Page 12 and 13: Statement 2: CAUTION: When replacin
- Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
- Page 16 and 17: Statement 13: DANGER Overloading a
- Page 18 and 19: xvi System x3200 M3 Types 7327 and
- Page 20 and 21: The following illustration shows th
- Page 22 and 23: Note: The illustrations in this doc
- Page 24 and 25: v If Autostart is enabled, insert t
- Page 26 and 27: Table 1. Features and specification
- Page 28 and 29: What your server offers The server
- Page 30 and 31: Computing Group (TCG) specification
- Page 32 and 33: IBM Systems Director v Memory chang
- Page 34 and 35: The following is an illustration of
- Page 36 and 37: Hard disk drive activity LED Power-
- Page 38 and 39: Rear view The following illustratio
- Page 40 and 41: v If a power failure occurs while t
- Page 42 and 43: System-board internal connectors Th
- Page 44 and 45: System-board switches and jumpers T
- Page 46 and 47: System-board external connectors Th
- Page 48 and 49: v Before you install optional hardw
- Page 50 and 51: Removing the side cover Important:
- Page 52 and 53: 6. Carefully pull the two bezel cli
- Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
- Page 56 and 57: v The following table lists the max
- Page 58 and 59: Installing drives Depending on the
- Page 62 and 63: Drive retainer clip 10. Slide the d
- Page 64 and 65: Server model with four hot-swap dri
- Page 66 and 67: To install a simple-swap hard disk
- Page 68 and 69: Installing an adapter The following
- Page 70 and 71: 8. If you are installing a full-len
- Page 72 and 73: Important: To ensure that any of yo
- Page 74 and 75: Note: Before you continue, check al
- Page 76 and 77: Installing the virtual media key To
- Page 78 and 79: 4. If you are instructed to return
- Page 80 and 81: Completing the installation If you
- Page 82 and 83: Reinstalling the side cover If you
- Page 84 and 85: Connecting external devices Install
- Page 86 and 87: Using the Setup utility The followi
- Page 88 and 89: Select this choice to view or set t
- Page 90 and 91: Passwords From the User Security me
- Page 92 and 93: Starting the backup server firmware
- Page 94 and 95: 2. The ServerGuide program stores i
- Page 96 and 97: Note: Approximately 1 to 3 minutes
- Page 98 and 99: 3. On the Welcome page, type a time
- Page 100 and 101: In addition, you can download an LS
- Page 102 and 103: Updating IBM Systems Director If yo
- Page 104 and 105: Software service and support You ca
- Page 106 and 107: Important notes Adobe and PostScrip
- Page 108 and 109: Electronic emission notices 3039 E.
DANGER<br />
Some laser products contain an embedded Class 3A or Class 3B laser<br />
diode. Note the following.<br />
Laser radiation when open. Do not stare into the beam, do not view<br />
directly with optical instruments, and avoid direct exposure to the<br />
beam.<br />
Class 1 Laser Product<br />
Laser Klasse 1<br />
Laser Klass 1<br />
Luokan 1 Laserlaite<br />
Appareil A ` Laser de Classe 1<br />
7. Touch the static-protective package that contains the drive to any unpainted<br />
metal surface on the server; then, remove the drive from the package and<br />
place it on a static-protective surface.<br />
8. Set any jumpers or switches on the drive according to the documentation that<br />
comes with the drive.<br />
Note: You might find it easier to install the new drive from the front and then<br />
attach the cables.<br />
9. Remove the drive retainer clip from the side of the drive cage of bay 1 or 2.<br />
Slide the drive retainer clip to the right to remove it from the drive cage; then,<br />
snap the drive retainer clip into the screw holes on the side of the drive.<br />
Release<br />
buttons<br />
Drive retainer<br />
clip<br />
10. If you are installing a 5.2-inch drive in bay 2, slide the drive into the bay. If you<br />
are installing a 3.5-inch drive in bay 2, you must attach the 5.2-inch.<br />
conversion kit to the 3.5-inch drive.<br />
Note: An optional diskette drive can be installed in bay 3.<br />
42 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide