User Manual - Etilize

More documents

Recommendations

Info

v The following table lists the maximum DIMM population using ranked RDIMM. Table 8. Maximum memory population using ranked RDIMMs (depending on your model) Number of RDIMMs DIMM type DIMM size Total memory 6 single-rank RDIMMs 1 GB 6 GB 6 single-rank RDIMMs 2 GB 12 GB 6 dual-rank RDIMMs 2 GB 12 GB 4 dual-rank RDIMMs 4 GB 16 GB 4 quad-rank RDIMMs 4 GB 16 GB 6 dual-rank RDIMMs 4 GB 24 GB 4 quad-rank RDIMMs 8 GB (when available) 32 GB v The following table lists the RDIMM memory population rule to optimize the system performance. Table 9. RDIMMs population rule for dual-channel symmetric mode DIMMs connector 1 DIMMs connector 2 DIMMs connector 3 DIMMs connector 4 DIMMs connector 5 DIMMs connector 6 populated empty empty empty empty empty populated empty empty populated empty empty populated populated empty populated populated empty populated populated populated populated populated populated The following illustration shows the location of the DIMM connectors on the system board. 38 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide DIMM 1 DIMM 2 DIMM 3 DIMM 4 DIMM 5 DIMM 6
Attention: Static electricity that is released to internal server components when the server is powered-on might cause the server to stop, which could result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist strap or other grounding system when working inside the server with the power on. To install a DIMM, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. Turn off the server and peripheral devices and disconnect the power cords and all external cables, if necessary. 3. Remove the cover (see “Removing the side cover” on page 32). 4. Open the retaining clip on each end of the DIMM connector. Attention: To avoid breaking the retaining clips or damaging the DIMM connectors, open and close the clips gently. 5. Touch the static-protective package that contains the DIMM to any unpainted metal surface on the outside of the server. Then, remove the DIMM from the package. 6. Turn the DIMM so that the DIMM keys align correctly with the connector. 7. Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at the ends of the DIMM connector (see “System-board optional-device connectors” on page 25 for the location of the DIMM connectors). 8. Firmly press the DIMM straight down into the connector by applying pressure on both ends of the DIMM simultaneously. The retaining clips snap into the locked position when the DIMM is firmly seated in the connector. Note: If there is a gap between the DIMM and the retaining clips, the DIMM has not been correctly inserted; open the retaining clips, remove the DIMM, and then reinsert it. If you have other devices to install or remove, do so now; otherwise, go to “Completing the installation” on page 62. Chapter 2. Installing optional devices 39
Page 1:
System x3200 M3 Types 7327 and 7328
Page 4 and 5:
Note: Before using this information
Page 6 and 7: Connecting external devices . . . .
Page 8 and 9: vi System x3200 M3 Types 7327 and 7
Page 10 and 11: Important: All caution and danger s
Page 12 and 13: Statement 2: CAUTION: When replacin
Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
Page 16 and 17: Statement 13: DANGER Overloading a
Page 18 and 19: xvi System x3200 M3 Types 7327 and
Page 20 and 21: The following illustration shows th
Page 22 and 23: Note: The illustrations in this doc
Page 24 and 25: v If Autostart is enabled, insert t
Page 26 and 27: Table 1. Features and specification
Page 28 and 29: What your server offers The server
Page 30 and 31: Computing Group (TCG) specification
Page 32 and 33: IBM Systems Director v Memory chang
Page 34 and 35: The following is an illustration of
Page 36 and 37: Hard disk drive activity LED Power-
Page 38 and 39: Rear view The following illustratio
Page 40 and 41: v If a power failure occurs while t
Page 42 and 43: System-board internal connectors Th
Page 44 and 45: System-board switches and jumpers T
Page 46 and 47: System-board external connectors Th
Page 48 and 49: v Before you install optional hardw
Page 50 and 51: Removing the side cover Important:
Page 52 and 53: 6. Carefully pull the two bezel cli
Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
Page 58 and 59: Installing drives Depending on the
Page 60 and 61: DANGER Some laser products contain
Page 62 and 63: Drive retainer clip 10. Slide the d
Page 64 and 65: Server model with four hot-swap dri
Page 66 and 67: To install a simple-swap hard disk
Page 68 and 69: Installing an adapter The following
Page 70 and 71: 8. If you are installing a full-len
Page 72 and 73: Important: To ensure that any of yo
Page 74 and 75: Note: Before you continue, check al
Page 76 and 77: Installing the virtual media key To
Page 78 and 79: 4. If you are instructed to return
Page 80 and 81: Completing the installation If you
Page 82 and 83: Reinstalling the side cover If you
Page 84 and 85: Connecting external devices Install
Page 86 and 87: Using the Setup utility The followi
Page 88 and 89: Select this choice to view or set t
Page 90 and 91: Passwords From the User Security me
Page 92 and 93: Starting the backup server firmware
Page 94 and 95: 2. The ServerGuide program stores i
Page 96 and 97: Note: Approximately 1 to 3 minutes
Page 98 and 99: 3. On the Welcome page, type a time
Page 100 and 101: In addition, you can download an LS
Page 102 and 103: Updating IBM Systems Director If yo
Page 104 and 105: Software service and support You ca
Page 106 and 107:
Important notes Adobe and PostScrip
Page 108 and 109:
Electronic emission notices 3039 E.
Page 110 and 111:
IBM verändert bzw. wenn Erweiterun
Page 112 and 113:
drive bay filler panel 41, 43 bay i
Page 114 and 115:
password administrator 72 forgotten
Page 116:
98 System x3200 M3 Types 7327 and 7
show all

User Manual - Etilize

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?