User Manual - Etilize
User Manual - Etilize User Manual - Etilize
System-board internal connectors The following illustration shows the internal connectors on the system board. System fan connector Virtual media key connector Battery Hypervisor key connector Main power Optical Drive Signal 24 System x3200 M3 Types 7327 and 7328: Installation and User’s Guide Wake on LAN Operator Information Panel HDD fan connector DIMM 1 DIMM 2 DIMM 3 DIMM 4 DIMM 5 DIMM 6 Microprocessor Microprocessor fan connector Optional internal USB tape drive connector Front USB connector ServeRAID-BR10il SAS/SATA controller connector Simple-swap hard disk drive backplane signal Hot-Swap HDD Backplane config 1 Hot-Swap HDD Backplane config 2
System-board optional-device connectors The following illustration shows the system-board and connectors for user-installable optional devices. Slot 1: PCIe2 x8(8,4,1) 25w Slot 2: PCIe2 x8(8,4,1) 25w Slot 3: PCIe2 x1 10w Slot 4: PCI 32bit, 33MHz Slot 5: PCI 32bit, 33MHz Virtual media key connector Battery Hypervisor key connector DIMM 1 DIMM 2 DIMM 3 DIMM 4 DIMM 5 DIMM 6 Microprocessor ServeRAID-BR10il SAS/SATA controller connector Chapter 2. Installing optional devices 25
- Page 1: System x3200 M3 Types 7327 and 7328
- Page 4 and 5: Note: Before using this information
- Page 6 and 7: Connecting external devices . . . .
- Page 8 and 9: vi System x3200 M3 Types 7327 and 7
- Page 10 and 11: Important: All caution and danger s
- Page 12 and 13: Statement 2: CAUTION: When replacin
- Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
- Page 16 and 17: Statement 13: DANGER Overloading a
- Page 18 and 19: xvi System x3200 M3 Types 7327 and
- Page 20 and 21: The following illustration shows th
- Page 22 and 23: Note: The illustrations in this doc
- Page 24 and 25: v If Autostart is enabled, insert t
- Page 26 and 27: Table 1. Features and specification
- Page 28 and 29: What your server offers The server
- Page 30 and 31: Computing Group (TCG) specification
- Page 32 and 33: IBM Systems Director v Memory chang
- Page 34 and 35: The following is an illustration of
- Page 36 and 37: Hard disk drive activity LED Power-
- Page 38 and 39: Rear view The following illustratio
- Page 40 and 41: v If a power failure occurs while t
- Page 44 and 45: System-board switches and jumpers T
- Page 46 and 47: System-board external connectors Th
- Page 48 and 49: v Before you install optional hardw
- Page 50 and 51: Removing the side cover Important:
- Page 52 and 53: 6. Carefully pull the two bezel cli
- Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
- Page 56 and 57: v The following table lists the max
- Page 58 and 59: Installing drives Depending on the
- Page 60 and 61: DANGER Some laser products contain
- Page 62 and 63: Drive retainer clip 10. Slide the d
- Page 64 and 65: Server model with four hot-swap dri
- Page 66 and 67: To install a simple-swap hard disk
- Page 68 and 69: Installing an adapter The following
- Page 70 and 71: 8. If you are installing a full-len
- Page 72 and 73: Important: To ensure that any of yo
- Page 74 and 75: Note: Before you continue, check al
- Page 76 and 77: Installing the virtual media key To
- Page 78 and 79: 4. If you are instructed to return
- Page 80 and 81: Completing the installation If you
- Page 82 and 83: Reinstalling the side cover If you
- Page 84 and 85: Connecting external devices Install
- Page 86 and 87: Using the Setup utility The followi
- Page 88 and 89: Select this choice to view or set t
- Page 90 and 91: Passwords From the User Security me
System-board internal connectors<br />
The following illustration shows the internal connectors on the system board.<br />
System fan<br />
connector<br />
Virtual<br />
media key<br />
connector<br />
Battery<br />
Hypervisor<br />
key connector<br />
Main<br />
power<br />
Optical<br />
Drive Signal<br />
24 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide<br />
Wake<br />
on<br />
LAN<br />
Operator<br />
Information<br />
Panel<br />
HDD fan connector<br />
DIMM 1<br />
DIMM 2<br />
DIMM 3<br />
DIMM 4<br />
DIMM 5<br />
DIMM 6<br />
Microprocessor<br />
Microprocessor<br />
fan connector<br />
Optional<br />
internal USB<br />
tape drive<br />
connector<br />
Front USB<br />
connector<br />
ServeRAID-BR10il<br />
SAS/SATA controller<br />
connector<br />
Simple-swap<br />
hard disk drive<br />
backplane signal<br />
Hot-Swap HDD<br />
Backplane config 1<br />
Hot-Swap HDD<br />
Backplane config 2