User Manual - Etilize

More documents

Recommendations

Info

Rear view The following illustration shows the LEDs and connectors on the rear of server models with hot-swap, redundant power supply. Power cord AC Power LED DC power LED Fault (error)LED Serial (Com1) Video USB 1 and 2 USB 3 and 4 Ethernet transmit/ receive activity LED (amber) Ethernet connector Ethernet link status LED (green) The following illustration shows the LEDs and connectors on the rear of server models with simple-swap, fixed power supply. Power-cord connector Connect the power cord to this connector. 20 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide
AC power LED This green LED provides status information about the power supply. During typical operation, both the ac and dc power LEDs are lit. For any other combination of LEDs, see the Problem Determination and Service Guide on the IBM System x Documentation CD. DC power LED This green LED provides status information about the power supply. During typical operation, both the ac and dc power LEDs are lit. For any other combination of LEDs, see the Problem Determination and Service Guide on the IBM System x Documentation CD. Power-error (Fault) LED When this amber LED is lit, it indicates that the power supply has failed. For any other combination of LEDs, see the Problem Determination and Service Guide on the IBM System x Documentation CD Video connector Connect a monitor to this connector. Note: The maximum video resolution is 1280 x 1024. Serial connector Connect a 9-pin serial device to this connector. USB connectors Connect USB devices to these connectors. Ethernet connectors Use either of these connectors to connect the server to a network. When you use the Ethernet 1 connector, the network can be shared with the IMM through a single network cable. Ethernet transmit/receive activity LED This LED is on the Ethernet connector on the rear of the server. When this LED is lit, it indicates that there is activity between the server and the network. Ethernet link status LED This LED is on the Ethernet connector on the rear of the server. When this LED is lit, it indicates that there is an active connection on the Ethernet port. Server power features When the server is connected to an ac power source but is not turned on, the operating system does not run, and all core logic except for the service processor (the integrated management module) is shut down; however, the server can respond to requests to the service processor, such as a remote request to turn on the server. The power-on LED flashes to indicate that the server is connected to ac power but is not turned on. Turning on the server Approximately 5 seconds after the server is connected to ac power, one or more fans might start running to provide cooling while the server is connected to power and the power-on button LED flashes quickly. Approximately 1 to 3 minutes after the server is connected to ac power, the power-control button becomes active (the power-on LED flashes slowly). You can turn on the server by pressing the power-control button. The server can also be turned on in any of the following ways: Chapter 1. The System x3200 M3 server 21
Page 1: System x3200 M3 Types 7327 and 7328
Page 4 and 5: Note: Before using this information
Page 6 and 7: Connecting external devices . . . .
Page 8 and 9: vi System x3200 M3 Types 7327 and 7
Page 10 and 11: Important: All caution and danger s
Page 12 and 13: Statement 2: CAUTION: When replacin
Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
Page 16 and 17: Statement 13: DANGER Overloading a
Page 18 and 19: xvi System x3200 M3 Types 7327 and
Page 20 and 21: The following illustration shows th
Page 22 and 23: Note: The illustrations in this doc
Page 24 and 25: v If Autostart is enabled, insert t
Page 26 and 27: Table 1. Features and specification
Page 28 and 29: What your server offers The server
Page 30 and 31: Computing Group (TCG) specification
Page 32 and 33: IBM Systems Director v Memory chang
Page 34 and 35: The following is an illustration of
Page 36 and 37: Hard disk drive activity LED Power-
Page 40 and 41: v If a power failure occurs while t
Page 42 and 43: System-board internal connectors Th
Page 44 and 45: System-board switches and jumpers T
Page 46 and 47: System-board external connectors Th
Page 48 and 49: v Before you install optional hardw
Page 50 and 51: Removing the side cover Important:
Page 52 and 53: 6. Carefully pull the two bezel cli
Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
Page 56 and 57: v The following table lists the max
Page 58 and 59: Installing drives Depending on the
Page 60 and 61: DANGER Some laser products contain
Page 62 and 63: Drive retainer clip 10. Slide the d
Page 64 and 65: Server model with four hot-swap dri
Page 66 and 67: To install a simple-swap hard disk
Page 68 and 69: Installing an adapter The following
Page 70 and 71: 8. If you are installing a full-len
Page 72 and 73: Important: To ensure that any of yo
Page 74 and 75: Note: Before you continue, check al
Page 76 and 77: Installing the virtual media key To
Page 78 and 79: 4. If you are instructed to return
Page 80 and 81: Completing the installation If you
Page 82 and 83: Reinstalling the side cover If you
Page 84 and 85: Connecting external devices Install
Page 86 and 87: Using the Setup utility The followi
Page 88 and 89:
Select this choice to view or set t
Page 90 and 91:
Passwords From the User Security me
Page 92 and 93:
Starting the backup server firmware
Page 94 and 95:
2. The ServerGuide program stores i
Page 96 and 97:
Note: Approximately 1 to 3 minutes
Page 98 and 99:
3. On the Welcome page, type a time
Page 100 and 101:
In addition, you can download an LS
Page 102 and 103:
Updating IBM Systems Director If yo
Page 104 and 105:
Software service and support You ca
Page 106 and 107:
Important notes Adobe and PostScrip
Page 108 and 109:
Electronic emission notices 3039 E.
Page 110 and 111:
IBM verändert bzw. wenn Erweiterun
Page 112 and 113:
drive bay filler panel 41, 43 bay i
Page 114 and 115:
password administrator 72 forgotten
Page 116:
98 System x3200 M3 Types 7327 and 7
show all

User Manual - Etilize

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?