User Manual - Etilize

More documents

Recommendations

Info

Hard disk drive activity LED Power-control button System error LED Power-on LED DVD drive activity LED (green) 0 1 2 3 4 5 6 7 DVD-eject button USB 2 USB 1 Hard disk drive activity LED (green) Hard disk drive status LED (amber) Power-control button and power-on LED Press this button to turn the server on and off manually or to wake the server from a reduced-power state. The states of the power-on LED are as follows: Off: AC power is not present, or the power supply or the LED itself has failed. Flashing rapidly (4 times per second): The server is turned off and is not ready to be turned on. The power-control button is disabled. This will last approximately 1 to 3 minutes. Flashing slowly (once per second): The server is turned off and is ready to be turned on. You can press the power-control button to turn on the server. Lit: The server is turned on. Fading on and off: The server is in a reduced-power state. To wake the server, press the power-control button or use the IMM Web interface. See “Logging on to the Web interface” on page 79 for information on logging on to the IMM Web interface. Hard disk drive activity LED When this LED is flashing rapidly, it indicates that a hard disk drive is in use. System-error LED When this amber LED is lit, it indicates that a system error has occurred. An LED on the system board might also be lit to help isolate the error. Detailed troubleshooting information is in the Problem Determination and Service Guide on the IBM System x Documentation CD. 18 System x3200 M3 Types 7327 and 7328: Installation and <strong>User</strong>’s Guide
USB connectors Connect USB devices to these connectors. DVD-eject button Press this button to release a CD or DVD from the DVD drive. DVD drive activity LED When this LED is lit, it indicates that the DVD drive is in use. Hot-swap hard disk drive activity LED (some models) On some server models, each hot-swap drive has a hard disk drive activity LED. When this green LED is flashing, it indicates that the associated hard disk drive is in use. When the drive is removed, this LED also is visible on the SAS/SATA backplane, next to the drive connector. The backplane is the printed circuit board behind drive bays 4 through 7 (or bays 4 through 11 on some 2.5-inch hard disk drive SAS models). Hot-swap hard disk drive status LED (some models) On some server models, each hot-swap hard disk drive has an amber status LED. If this amber status LED is lit, it indicates that the associated hard disk drive has failed. If an optional ServeRAID adapter is installed in the server and the LED flashes slowly (one flash per second), the drive is being rebuilt. If the LED flashes rapidly (three flashes per second), the adapter is identifying the drive. When the drive is removed, this LED also is visible on the SAS/SATA backplane, below the hot-swap hard disk drive activity LED. Chapter 1. The System x3200 M3 server 19
Page 1: System x3200 M3 Types 7327 and 7328
Page 4 and 5: Note: Before using this information
Page 6 and 7: Connecting external devices . . . .
Page 8 and 9: vi System x3200 M3 Types 7327 and 7
Page 10 and 11: Important: All caution and danger s
Page 12 and 13: Statement 2: CAUTION: When replacin
Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
Page 16 and 17: Statement 13: DANGER Overloading a
Page 18 and 19: xvi System x3200 M3 Types 7327 and
Page 20 and 21: The following illustration shows th
Page 22 and 23: Note: The illustrations in this doc
Page 24 and 25: v If Autostart is enabled, insert t
Page 26 and 27: Table 1. Features and specification
Page 28 and 29: What your server offers The server
Page 30 and 31: Computing Group (TCG) specification
Page 32 and 33: IBM Systems Director v Memory chang
Page 34 and 35: The following is an illustration of
Page 38 and 39: Rear view The following illustratio
Page 40 and 41: v If a power failure occurs while t
Page 42 and 43: System-board internal connectors Th
Page 44 and 45: System-board switches and jumpers T
Page 46 and 47: System-board external connectors Th
Page 48 and 49: v Before you install optional hardw
Page 50 and 51: Removing the side cover Important:
Page 52 and 53: 6. Carefully pull the two bezel cli
Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
Page 56 and 57: v The following table lists the max
Page 58 and 59: Installing drives Depending on the
Page 60 and 61: DANGER Some laser products contain
Page 62 and 63: Drive retainer clip 10. Slide the d
Page 64 and 65: Server model with four hot-swap dri
Page 66 and 67: To install a simple-swap hard disk
Page 68 and 69: Installing an adapter The following
Page 70 and 71: 8. If you are installing a full-len
Page 72 and 73: Important: To ensure that any of yo
Page 74 and 75: Note: Before you continue, check al
Page 76 and 77: Installing the virtual media key To
Page 78 and 79: 4. If you are instructed to return
Page 80 and 81: Completing the installation If you
Page 82 and 83: Reinstalling the side cover If you
Page 84 and 85: Connecting external devices Install
Page 86 and 87:
Using the Setup utility The followi
Page 88 and 89:
Select this choice to view or set t
Page 90 and 91:
Passwords From the User Security me
Page 92 and 93:
Starting the backup server firmware
Page 94 and 95:
2. The ServerGuide program stores i
Page 96 and 97:
Note: Approximately 1 to 3 minutes
Page 98 and 99:
3. On the Welcome page, type a time
Page 100 and 101:
In addition, you can download an LS
Page 102 and 103:
Updating IBM Systems Director If yo
Page 104 and 105:
Software service and support You ca
Page 106 and 107:
Important notes Adobe and PostScrip
Page 108 and 109:
Electronic emission notices 3039 E.
Page 110 and 111:
IBM verändert bzw. wenn Erweiterun
Page 112 and 113:
drive bay filler panel 41, 43 bay i
Page 114 and 115:
password administrator 72 forgotten
Page 116:
98 System x3200 M3 Types 7327 and 7
show all

User Manual - Etilize

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?