User Manual - Etilize
User Manual - Etilize User Manual - Etilize
Important: All caution and danger statements in this documentation begin with a number. This number is used to cross reference an English caution or danger statement with translated versions of the caution or danger statement in the IBM Safety Information book. For example, if a caution statement begins with a number 1, translations for that caution statement appear in the IBM Safety Information book under statement 1. Be sure to read all caution and danger statements in this documentation before performing the instructions. Read any additional safety information that comes with the blade server or optional device before you install the device. viii System x3200 M3 Types 7327 and 7328: Installation and User’s Guide
Statement 1: DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. v Connect all power cords to a properly wired and grounded electrical outlet. v Connect to properly wired outlets any equipment that will be attached to this product. v When possible, use one hand only to connect or disconnect signal cables. v Never turn on any equipment when there is evidence of fire, water, or structural damage. v Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. v Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. To Connect: To Disconnect: 1. Turn everything OFF. 2. First, attach all cables to devices. 3. Attach signal cables to connectors. 4. Attach power cords to outlet. 5. Turn device ON. 1. Turn everything OFF. 2. First, remove power cords from outlet. 3. Remove signal cables from connectors. 4. Remove all cables from devices. Safety ix
- Page 1: System x3200 M3 Types 7327 and 7328
- Page 4 and 5: Note: Before using this information
- Page 6 and 7: Connecting external devices . . . .
- Page 8 and 9: vi System x3200 M3 Types 7327 and 7
- Page 12 and 13: Statement 2: CAUTION: When replacin
- Page 14 and 15: Statement 4: ≥ 18 kg (39.7 lb)
- Page 16 and 17: Statement 13: DANGER Overloading a
- Page 18 and 19: xvi System x3200 M3 Types 7327 and
- Page 20 and 21: The following illustration shows th
- Page 22 and 23: Note: The illustrations in this doc
- Page 24 and 25: v If Autostart is enabled, insert t
- Page 26 and 27: Table 1. Features and specification
- Page 28 and 29: What your server offers The server
- Page 30 and 31: Computing Group (TCG) specification
- Page 32 and 33: IBM Systems Director v Memory chang
- Page 34 and 35: The following is an illustration of
- Page 36 and 37: Hard disk drive activity LED Power-
- Page 38 and 39: Rear view The following illustratio
- Page 40 and 41: v If a power failure occurs while t
- Page 42 and 43: System-board internal connectors Th
- Page 44 and 45: System-board switches and jumpers T
- Page 46 and 47: System-board external connectors Th
- Page 48 and 49: v Before you install optional hardw
- Page 50 and 51: Removing the side cover Important:
- Page 52 and 53: 6. Carefully pull the two bezel cli
- Page 54 and 55: U = Unbuffered DIMM with no ECC (x6
- Page 56 and 57: v The following table lists the max
- Page 58 and 59: Installing drives Depending on the
Statement 1:<br />
DANGER<br />
Electrical current from power, telephone, and communication cables is<br />
hazardous.<br />
To avoid a shock hazard:<br />
v Do not connect or disconnect any cables or perform installation,<br />
maintenance, or reconfiguration of this product during an electrical<br />
storm.<br />
v Connect all power cords to a properly wired and grounded electrical<br />
outlet.<br />
v Connect to properly wired outlets any equipment that will be attached to<br />
this product.<br />
v When possible, use one hand only to connect or disconnect signal<br />
cables.<br />
v Never turn on any equipment when there is evidence of fire, water, or<br />
structural damage.<br />
v Disconnect the attached power cords, telecommunications systems,<br />
networks, and modems before you open the device covers, unless<br />
instructed otherwise in the installation and configuration procedures.<br />
v Connect and disconnect cables as described in the following table when<br />
installing, moving, or opening covers on this product or attached<br />
devices.<br />
To Connect: To Disconnect:<br />
1. Turn everything OFF.<br />
2. First, attach all cables to devices.<br />
3. Attach signal cables to connectors.<br />
4. Attach power cords to outlet.<br />
5. Turn device ON.<br />
1. Turn everything OFF.<br />
2. First, remove power cords from outlet.<br />
3. Remove signal cables from connectors.<br />
4. Remove all cables from devices.<br />
Safety ix