Telemotive Pre-Engineered SLTX Transmitter - Enrange LLC Radio ...
Telemotive Pre-Engineered SLTX Transmitter - Enrange LLC Radio ...
Telemotive Pre-Engineered SLTX Transmitter - Enrange LLC Radio ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
3.1: <strong>SLTX</strong> <strong>Transmitter</strong> Board Setup Information.<br />
The <strong>SLTX</strong> <strong>Transmitter</strong> Board is shown in Figure 3-1. Refer to paragraphs 3.1 through 336 for servicing<br />
procedures.<br />
M5 M4 M3 M2<br />
J29 J28 J27 J34 J33 J21 J4 J3 J2 J7 J6 J5<br />
J32 J31 J30 J17 J35 J19 J18 J14 J13 J12 J11 J10 J9 J8<br />
ANT. M6 J36 J38 J37<br />
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1<br />
M7<br />
TP2<br />
GND<br />
TP5<br />
POWER<br />
CONTROL<br />
TP4 +5V<br />
TP3 DATA<br />
OFF<br />
OFF<br />
OFF<br />
OFF<br />
8---------1 8---------1 8---------1 8---------1<br />
SW2 “A” SW1 “B” “A” SW4 “D” SW3 “C”<br />
J23<br />
EXTERNAL CODE PLUG<br />
EPROM<br />
E10642<br />
J9 Firmware Loading<br />
Connector<br />
Firmware<br />
Number Label<br />
J39<br />
J20 Power<br />
connector<br />
RPOT1<br />
RPOT2<br />
TP1<br />
J1<br />
J24<br />
J15<br />
J25<br />
J26<br />
TP6<br />
J40<br />
Battery<br />
ON/OFF LED<br />
Key switch<br />
ON/OFF switch<br />
EMS (ESTOP)<br />
Not used<br />
Reset<br />
Figure 3-1. <strong>SLTX</strong> <strong>Transmitter</strong> Board<br />
3.2: Access Codes Switches. (SW1 and SW2). Setting Access Code (for units with no external code plug<br />
only).<br />
The access code is set at the factory and should not be changed unless absolutely necessary. If a spare transmitter<br />
unit is used, the receiver unit access code should be changed to match the access code of the spare transmitter<br />
unit. For Part 15 systems the access codes are printed on a white label on the outside of any transmitter and may<br />
be matched to “A” and “B” on the receiver CPU Board without having to open the transmitter housing.<br />
Switch SW2 (B) in the transmitter must match switch (B) on the receiver CPU Board and switch SW1 (A) in the<br />
transmitter must match switch (A) on the receiver CPU Board.<br />
If you are reprogramming a spare transmitter make sure the other transmitter is securely taken out of service.<br />
WARNING<br />
TWO OPERATIONAL TRANSMITTERS WITH THE SAME ACCESS CODES OPERATING AT THE SAME<br />
TIME IS A DEFINITE SAFETY HAZARD. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN<br />
SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.<br />
<strong>Telemotive</strong> receivers are shipped with the access code settings for the transmitter marked on the receiver door.<br />
<strong>Telemotive</strong> <strong>Pre</strong><strong>Engineered</strong> <strong>SLTX</strong> <strong>Transmitter</strong> Instruction Manual—March 2010<br />
10