Fabric Manager Users Guide, Version 6.1, Revision A - QLogic

More documents

Recommendations

Info

3–Fabric Manager Configuration Configuring the QLogic Fabric Manager 0 10 0 0 60 0 600 3 The parameters in Table 3-16 control Fabric Sweep. 3-44 IB0054608-01 B
3–Fabric Manager Configuration Configuring the QLogic Fabric Manager Table 3-16. Sm Fabric Sweep Parameters Parameter Default Value Description SweepInterval 300 The SM sweeps immediately upon fabric changes based on traps from the switches. Since traps can be lost, the SM also has a slow periodic sweep at a maximum of SweepInterval seconds to verify fabric config. IgnoreTraps 0 Do not sweep or log when traps occur when enabled (1) MaxAttempts RespTimeout MinRespTimeout SweepErrorsThreshold SweepAbandonThreshold 3 250 35 0 3 The SM will spend up to RespTimeout multiplied by MaxAttempts per packet. These allow two modes of operation. When MinRespTimeout is non-zero: the SM will start with MinRespTimeout as the time-out value for requests and use multiples of this value for subsequent attempts if there is a time-out in the previous attempt. SM will keep retrying until the cumulative sum of time-outs for retries is less than RespTimeout multiplied by MaxAttempts. This approach is recommended and will react quickly to lost packets while still allowing adequate time for slower SMAs to respond. When MinRespTimeout is zero: upon a time-out, up to MaxAttempts are attempted with each attempt having a time-out of Resp- Timeout. This approach is provided for backward compatibility with previous SM versions. When there are a large number of fabric changes at once, the SM could have lots of errors while attempting to access/program devices which disappeared mid-sweep. If the SM receives more than the set SweepErrorsThreshold parameter of errors in a given sweep, it will give up and start the sweep over. When the SM abandons more than the set SweepAbandonThreshold parameter of sweeps in a row the SM will do its best to complete the sweep. TrapThreshold 0 If a given port issues more than the Trap- Threshold traps/minute value it will be disabled as an unstable port. 0 disables this feature. IB0054608-01 B 3-45
Page 1 and 2:
User Guide Fabric Manager 7.0.1 IB0
Page 3 and 4:
Table of Contents Preface Intended
Page 5 and 6:
Fabric Manager 7.0.1 User Guide Fab
Page 7 and 8:
Fabric Manager 7.0.1 User Guide 4 V
Page 9 and 10:
Fabric Manager 7.0.1 User Guide D E
Page 11 and 12:
Preface Intended Audience This manu
Page 13 and 14:
For details about available service
Page 15 and 16:
1 Overview of the QLogic Fabric Man
Page 17 and 18:
1-Overview of the QLogic Fabric Man
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
2 Advanced Fabric Manager Capabilit
Page 31 and 32:
2-Advanced Fabric Manager Capabilit
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64: 2-Advanced Fabric Manager Capabilit
Page 71 and 72: 3 Fabric Manager Configuration This
Page 73 and 74: 3-Fabric Manager Configuration Conf
Page 113: 3-Fabric Manager Configuration Conf
Page 145 and 146: 4 Virtual Fabrics Overview Virtual
Page 147 and 148: 4-Virtual Fabrics Configuration Eac
Page 149 and 150: 4-Virtual Fabrics Configuration Tab
Page 151 and 152: 4-Virtual Fabrics Configuration The
Page 153 and 154: 4-Virtual Fabrics Configuration 0
Page 155 and 156: 4-Virtual Fabrics Configuration All
Page 157 and 158: 4-Virtual Fabrics Configuration . T
Page 165 and 166:
4-Virtual Fabrics Configuration Sec
Page 167 and 168:
4-Virtual Fabrics Configuration Tab
Page 169 and 170:
4-Virtual Fabrics Configuration The
Page 171 and 172:
4-Virtual Fabrics Configuration
Page 173 and 174:
4-Virtual Fabrics Configuration Al
Page 175 and 176:
5 Embedded Fabric Manager Commands
Page 177 and 178:
5-Embedded Fabric Manager Commands
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
6 Installation and Set Up Installin
Page 255 and 256:
6-Installation and Set Up Installin
Page 257 and 258:
6-Installation and Set Up Installin
Page 259 and 260:
A Fabric Manager Command Line Inter
Page 261 and 262:
A-Fabric Manager Command Line Inter
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
B QLogic Fabric Manager Log Message
Page 277 and 278:
B-QLogic Fabric Manager Log Message
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
C Mapping Old Parameters Versions o
Page 309 and 310:
C-Mapping Old Parameters Old SM Par
Page 311 and 312:
C-Mapping Old Parameters Old SM Par
Page 313 and 314:
C-Mapping Old Parameters Old PM Par
Page 315 and 316:
C-Mapping Old Parameters Old BM Par
Page 317 and 318:
D QOS Options in a Mesh/Torus vFabr
Page 319 and 320:
E ./INSTALL Syntax Syntax ./INSTALL
Page 322:
Corporate Headquarters QLogic Corpo
show all

Fabric Manager Users Guide, Version 6.1, Revision A - QLogic

Create successful ePaper yourself

Delete template?

Save as template?