IQ204/ADL Autodialling Controller Data Sheet - Trend

Data Sheet
IQ204/ADL
SPECIFICATIONS
Electrical
CPU
:68334 32 bit micro controller
CPU speed
:16.78 MHz
Cycle time
:1 s
Memory
:128 kbyte battery backed SRAM, and
256 kbyte Flash.
Input power
/230 :230 Vac +15 -10 %, 50 to 60 Hz
/24 :24 Vac ±10%, 50 to 60 Hz
Consumption :22 VA max.
Battery backup :Non-rechargeable lithium plug-in cell,
maintains time and logged data with input
power off for 5 years minimum.
Battery type
:Saft LM2450, 3 V, or equivalent
Clock accuracy :30 s per month typical.
Auxiliary output supply
/230 :24 Vdc nominal (unregulated), 23 to
28 Vdc @ 230 Vac
/24 :24 Vdc ± 5 % regulated
Both versions have 200 mA (180 mA with
modem connected) available for
accessory loads in addition to full
complement of I/O and external display
panel. Protected by solid state self
resetting thermal fuse. The available
current may be increased by reducing
input loading (see page 4 for available
current calculation).
2-line Display Panel :Optional 2x40 character display, with 4
programmable softkeys. Can be
mounted externally using adaptor cable
supplied with display panel.
Modem
:V22bis, V22, V21. Will communicate
with any TMN >=V4.0, V22bis (e.g.
TMNH). The modem is compatible with
most major networks in the world. It
complies with FCC Part 68 USA, IC CS03
Canada, TS 002 Australia, and CTR21,
for use with all telephone networks of the
European Union. Consumes 20 mA
maximum (equivalent) from 24 V input
power when in use.
Supervisor port transmission
:Either RS232 or RS485 selected by
on-board link, default setting is RS232.
RS232
:EIA RS232, EIA/TIA232E, V28
RS485
:RS485
Network
:20 mA serial 2 wire current loop,
opto-isolated, polarity independent
receiver, balanced transmitter.
Distance
Supervisor port :RS232, 15 m (16 yds). RS485, 100 m
(110 yds).
Network
:Dependent on cable type, see table
below:
Cable
Belden 9182
Belden 9207
Trend
TP/1/1/22/HF/500
(Belden 8761)
Trend
TP/2/2/22/HF/500
(Belden 8723)
Baud rate
Network
Supervisor port
1k2
baud
9k6
baud
19k2
baud
No. of Wires
1000 m 1000 m 700 m
(1090 yds) (1090 yds) (765 yds)
2
1000 m 1000 m 500 m
(1090 yds) (1090 yds) (545 yds)
2
1000 m
(1090 yds)
1000 m
(1090 yds)
700 m
(765 yds)
500 m
(545 yds)
350 m
(380 yds)
250 m
(270 yds)
:Selectable by switch 1k2, 9k6, or 19k2
- set to be same as other nodes on Lan.
:9k6.
2
4
Network addresses
Controller
Supervisor port
Signal Cable
:Selectable by switch, 116 nodes
addressable (1,4 to 119 excluding 10) -
recommended address range 11 to 117
- set to be unique on Lan.
:Software selectable, 116 nodes
addressable (1,4 to 119 excluding 10) -
set to be unique on Lan. Defaults to
controller address plus 1, but if controller
address is less than 11, supervisor port
defaults to 20.
:Analogue, Thermistor, or Digital inputs,
and Analogue outputs. Trend TP/1/1/22/
HF/500 recommended (Belden 8761) -
Cu only.
Analogue inputs :Channels A1 to A8, 12 bit resolution
(4096 steps - effective). Minimum 60 dB
series mode rejection at supply
frequency. Linkable for analogue current
(I), analogue voltage (V), thermistor (T).
analogue current (I):0 to 20 mA, input resistance 240 Ω,
accuracy ±0.5 % of span (i.e. 100 μA),
loop powered input power is 20 to 30 Vdc.
analogue voltage (V) :0 to 10 V, input resistance 200 kΩ,
accuracy 50 mV equivalent to ±0.5 % of
span.
thermistor (T) :Thermistor bridge resistor 10 kΩ 0.1%,
accuracy 0.5 % span. Bridge supply 5 V.
Digital Inputs :Channels D1 to D8. Volt free contact.
24 V input power. Wetting current = 1.8
mA. Count rate 30 Hz max.
Analogue outputs :Channels B1 to B8. 11 bit resolution
(2048 steps). 0 to 10 V with 20 mA current
limit, accuracy ±0.5 % of span (50 mV).
Indicators
RX
:(yellow) ON if current is entering network
receiver
TX
:(yellow) ON if current is flowing from
network transmitter
OK (Lan OK) :(green) ON if network is operating.
Flashes if prohibited controller network
address set (0,2,3,>119).
Mechanical
Dimensions
Enclosure material
Weight
Connectors
Input power
:255 mm (10.04”) x 180 mm (7.09”) x
57 mm (2.24”).
:1 mm (0.039”) zinc passivated mild steel
:1.5 kg (3.3 lbs).
:2 part connector for 0.5 to 2.5 mm 2 cross
section area (14 to 20 AWG) cable.
Network :2 part connectors for 0.5 to 2.5 mm 2
cross section area (14 to 20 AWG) cable.
I/O :2 part connectors for 0.5 to 2.5 mm 2
cross section area (14 to 20 AWG) cable
- Cu only
Supervisor port (RS232):RJ11 (FCC68) normally for modem
using adapter cable (supplied).
Modem may be unplugged so that port
may be used by IQ system utility software
PC connected using adaptor cable,
CABLE/EJ101442 or by NDP or GDP+.
Supplies signal and power to NDP using
CABLE/EJ104209 and to GDP+/RS232
using special cable.
Supervisor port (RS485):RJ45 (FCC68). For GDP+/RS485
using special cable.
Display panel 25 way D type.
IQ204/ADL Autodailling Controller Data Sheet TA200489 Issue 1/E 01/11/06
11