<strong>IQ204</strong>/<strong>ADL</strong> <strong>Data</strong> <strong>Sheet</strong> This page is intentionally left blank. 10 <strong>IQ204</strong>/<strong>ADL</strong> Autodailling <strong>Controller</strong> <strong>Data</strong> <strong>Sheet</strong> TA200489 Issue 1/E 01/11/06
<strong>Data</strong> <strong>Sheet</strong> <strong>IQ204</strong>/<strong>ADL</strong> SPECIFICATIONS Electrical CPU :68334 32 bit micro controller CPU speed :16.78 MHz Cycle time :1 s Memory :128 kbyte battery backed SRAM, and 256 kbyte Flash. Input power /230 :230 Vac +15 -10 %, 50 to 60 Hz /24 :24 Vac ±10%, 50 to 60 Hz Consumption :22 VA max. Battery backup :Non-rechargeable lithium plug-in cell, maintains time and logged data with input power off for 5 years minimum. Battery type :Saft LM2450, 3 V, or equivalent Clock accuracy :30 s per month typical. Auxiliary output supply /230 :24 Vdc nominal (unregulated), 23 to 28 Vdc @ 230 Vac /24 :24 Vdc ± 5 % regulated Both versions have 200 mA (180 mA with modem connected) available for accessory loads in addition to full complement of I/O and external display panel. Protected by solid state self resetting thermal fuse. The available current may be increased by reducing input loading (see page 4 for available current calculation). 2-line Display Panel :Optional 2x40 character display, with 4 programmable softkeys. Can be mounted externally using adaptor cable supplied with display panel. Modem :V22bis, V22, V21. Will communicate with any TMN >=V4.0, V22bis (e.g. TMNH). The modem is compatible with most major networks in the world. It complies with FCC Part 68 USA, IC CS03 Canada, TS 002 Australia, and CTR21, for use with all telephone networks of the European Union. Consumes 20 mA maximum (equivalent) from 24 V input power when in use. Supervisor port transmission :Either RS232 or RS485 selected by on-board link, default setting is RS232. RS232 :EIA RS232, EIA/TIA232E, V28 RS485 :RS485 Network :20 mA serial 2 wire current loop, opto-isolated, polarity independent receiver, balanced transmitter. Distance Supervisor port :RS232, 15 m (16 yds). RS485, 100 m (110 yds). Network :Dependent on cable type, see table below: Cable Belden 9182 Belden 9207 <strong>Trend</strong> TP/1/1/22/HF/500 (Belden 8761) <strong>Trend</strong> TP/2/2/22/HF/500 (Belden 8723) Baud rate Network Supervisor port 1k2 baud 9k6 baud 19k2 baud No. of Wires 1000 m 1000 m 700 m (1090 yds) (1090 yds) (765 yds) 2 1000 m 1000 m 500 m (1090 yds) (1090 yds) (545 yds) 2 1000 m (1090 yds) 1000 m (1090 yds) 700 m (765 yds) 500 m (545 yds) 350 m (380 yds) 250 m (270 yds) :Selectable by switch 1k2, 9k6, or 19k2 - set to be same as other nodes on Lan. :9k6. 2 4 Network addresses <strong>Controller</strong> Supervisor port Signal Cable :Selectable by switch, 116 nodes addressable (1,4 to 119 excluding 10) - recommended address range 11 to 117 - set to be unique on Lan. :Software selectable, 116 nodes addressable (1,4 to 119 excluding 10) - set to be unique on Lan. Defaults to controller address plus 1, but if controller address is less than 11, supervisor port defaults to 20. :Analogue, Thermistor, or Digital inputs, and Analogue outputs. <strong>Trend</strong> TP/1/1/22/ HF/500 recommended (Belden 8761) - Cu only. Analogue inputs :Channels A1 to A8, 12 bit resolution (4096 steps - effective). Minimum 60 dB series mode rejection at supply frequency. Linkable for analogue current (I), analogue voltage (V), thermistor (T). analogue current (I):0 to 20 mA, input resistance 240 Ω, accuracy ±0.5 % of span (i.e. 100 μA), loop powered input power is 20 to 30 Vdc. analogue voltage (V) :0 to 10 V, input resistance 200 kΩ, accuracy 50 mV equivalent to ±0.5 % of span. thermistor (T) :Thermistor bridge resistor 10 kΩ 0.1%, accuracy 0.5 % span. Bridge supply 5 V. Digital Inputs :Channels D1 to D8. Volt free contact. 24 V input power. Wetting current = 1.8 mA. Count rate 30 Hz max. Analogue outputs :Channels B1 to B8. 11 bit resolution (2048 steps). 0 to 10 V with 20 mA current limit, accuracy ±0.5 % of span (50 mV). Indicators RX :(yellow) ON if current is entering network receiver TX :(yellow) ON if current is flowing from network transmitter OK (Lan OK) :(green) ON if network is operating. Flashes if prohibited controller network address set (0,2,3,>119). Mechanical Dimensions Enclosure material Weight Connectors Input power :255 mm (10.04”) x 180 mm (7.09”) x 57 mm (2.24”). :1 mm (0.039”) zinc passivated mild steel :1.5 kg (3.3 lbs). :2 part connector for 0.5 to 2.5 mm 2 cross section area (14 to 20 AWG) cable. Network :2 part connectors for 0.5 to 2.5 mm 2 cross section area (14 to 20 AWG) cable. I/O :2 part connectors for 0.5 to 2.5 mm 2 cross section area (14 to 20 AWG) cable - Cu only Supervisor port (RS232):RJ11 (FCC68) normally for modem using adapter cable (supplied). Modem may be unplugged so that port may be used by IQ system utility software PC connected using adaptor cable, CABLE/EJ101442 or by NDP or GDP+. Supplies signal and power to NDP using CABLE/EJ104209 and to GDP+/RS232 using special cable. Supervisor port (RS485):RJ45 (FCC68). For GDP+/RS485 using special cable. Display panel 25 way D type. <strong>IQ204</strong>/<strong>ADL</strong> Autodailling <strong>Controller</strong> <strong>Data</strong> <strong>Sheet</strong> TA200489 Issue 1/E 01/11/06 11
Change language