OPERATOR'S MANUAL - Ridgid
OPERATOR'S MANUAL - Ridgid OPERATOR'S MANUAL - Ridgid
ACCESSORIES Item ......................................................................................................................................................................... Part No. Rip Fence .................................................................................................................................................................. AC5001 Riser Block ................................................................................................................................................................ AC5005 Sanding Belts ............................................................................................................................................................ AC5006 Cool Blocks ........................................................................................................................................................... AC5007 Miter Gauge............................................................................................................................................................... AC1021 Herc-U-Lift PLUS................................................................................................................................................... AC9950 WARNING: Current attachments and accessories available for use with this tool are listed above. Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. TROUBLESHOOTING Problem Cause Solution Excessive noise Motor Have motor checked by qualified service technician. Repair service is available your nearest Authorized Service Center store. Motor fails to develop full power. NOTE: Low Voltage Power output of motor decreases rapidly with decrease in voltage at motor terminals. For example, a reduction of 10% in voltage causes a reduction of 19% in maximum power output of which the motor is capable, and a reduction of 20% in voltage causes a reduction of 36% in maximum power output Circuit overloaded with light, appliances and other motors. Under size wires or circuit too long. General overloading of power company facilities. Do not use other appliances or motors on same circuit when using the saw. Increase wire sizes, or reduce length of wiring. See Electrical section. Request a voltage check from the power company. Motor starts slowly or fails to come up to full speed Motor overloaded. Improper cooling (air circulation restricted through motor due to sawdust accumulation) Feed work slower into blade. Clean out sawdust to provide normal air circulation through motor. See Maintenance section. Starting switch in motor will not operate. Burned switch contacts (due to extended hold-in periods caused by low line voltage, etc.) Shorted capacitor. Loose or broken connections. Have switch replaced and request a voltage check from the power company. Have capacitor tested and replace if defective. Have wiring checked and repaired. 32
TROUBLESHOOTING Problem Cause Solution Motor stalls (resulting in blown fuses or tripped circuit breakers). Starting switch not operating. Voltage too low to permit motor to reach operating speed. Fuses or circuit breakers do not have sufficient capacity Have switch replaced. Request voltage check from the power company. Install proper size fuses or circuit breakers. Frequent opening of fuses or circuit breakers. Motor overloaded. Fuses or circuit breakers do not have sufficient capacity. Starting switch not operating (motor does not reach speed) Feed work slower into blade. Install proper size fuses or circuit breakers. Check that wiring will handle load. Have switch replaced. Blow out sawdust. Blade does not run in the approximate center of the upper wheel. Not tracking properly. Adjust tracking, see Assembly section, "Tracking the Blade” section. Band Saw slows down when cutting. Belt too loose. Cutting too small a radius. Dull blade. Overloading motor. Adjust belt tension, see Assembly section, “Mounting the Motor Assembly”. Stop feeding, and back up the material slightly, until the band saw speeds up. Replace blade. Slow down, trying to cut too fast. Blades breaking Too much tension on blade. Adjust tension. See Assembly section, “Adjusting Blade Tension”. Kink in blade caused cutting too small a radius or turning the material too fast when cutting. Use correct cutting technique. See Operation section. Blade dulls too quickly. Blade guides set too close to teeth. Cutting incorrect material. Adjust upper and lower blades guides. See Assembly section “Installing and Adjusting the blade”. Band saw vibrates. Too much tension on motor belt. Adjust according to “Mounting the Motor Assembly” section. 33
- Page 1 and 2: ON I P U L L P U S H O 10° 0° 15
- Page 3 and 4: GENERAL SAFETY RULES WARNING: Read
- Page 5 and 6: SYMBOLS Some of the following symbo
- Page 7 and 8: GLOSSARY OF TERMS Bevel Cut A cutti
- Page 9 and 10: ELECTRICAL CHANGING MOTOR VOLTAGE S
- Page 11 and 12: FEATURES KNOW YOUR BAND SAW See Fig
- Page 13 and 14: LOOSE PARTS The following items are
- Page 15 and 16: ASSEMBLY UNPACKING This product req
- Page 17 and 18: ASSEMBLY MOUNTING THE MOTOR ASSEMBL
- Page 19 and 20: I ASSEMBLY MOUNTING THE SWITCH BOX
- Page 21 and 22: ASSEMBLY • Replace throat plate a
- Page 23 and 24: I P U L L P U S H O 0° 15° 30° 4
- Page 25 and 26: OPERATION WARNING: Do not allow fam
- Page 27 and 28: OPERATION TILTING THE TABLE See Fig
- Page 29 and 30: I L P ADJUSTMENTS • Rotate guard
- Page 31: MAINTENANCE LUBRICATION All the bea
- Page 35 and 36: WARRANTY RIDGID ® HAND HELD AND ST
ACCESSORIES<br />
Item ......................................................................................................................................................................... Part No.<br />
Rip Fence .................................................................................................................................................................. AC5001<br />
Riser Block ................................................................................................................................................................ AC5005<br />
Sanding Belts ............................................................................................................................................................ AC5006<br />
Cool Blocks ........................................................................................................................................................... AC5007<br />
Miter Gauge............................................................................................................................................................... AC1021<br />
Herc-U-Lift PLUS................................................................................................................................................... AC9950<br />
WARNING:<br />
Current attachments and accessories available for use with this tool are listed above. Do not use any attachments<br />
or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not<br />
recommended can result in serious personal injury.<br />
TROUBLESHOOTING<br />
Problem Cause Solution<br />
Excessive noise<br />
Motor<br />
Have motor checked by qualified service<br />
technician. Repair service is available your<br />
nearest Authorized Service Center store.<br />
Motor fails to develop full power.<br />
NOTE: Low Voltage Power output<br />
of motor decreases rapidly with<br />
decrease in voltage at motor<br />
terminals. For example, a reduction<br />
of 10% in voltage causes a<br />
reduction of 19% in maximum<br />
power output of which the motor is<br />
capable, and a reduction of 20% in<br />
voltage causes a reduction of 36%<br />
in maximum power output<br />
Circuit overloaded with light,<br />
appliances and other motors.<br />
Under size wires or circuit too long.<br />
General overloading of power company<br />
facilities.<br />
Do not use other appliances or motors on<br />
same circuit when using the saw.<br />
Increase wire sizes, or reduce length of<br />
wiring. See Electrical section.<br />
Request a voltage check from the power<br />
company.<br />
Motor starts slowly or fails to come<br />
up to full speed<br />
Motor overloaded.<br />
Improper cooling (air circulation<br />
restricted through motor due to sawdust<br />
accumulation)<br />
Feed work slower into blade.<br />
Clean out sawdust to provide normal<br />
air circulation through motor. See<br />
Maintenance section.<br />
Starting switch in motor will not<br />
operate.<br />
Burned switch contacts (due to<br />
extended hold-in periods caused by<br />
low line voltage, etc.)<br />
Shorted capacitor.<br />
Loose or broken connections.<br />
Have switch replaced and request a<br />
voltage check from the power company.<br />
Have capacitor tested and replace if<br />
defective.<br />
Have wiring checked and repaired.<br />
32
Change language