OPERATOR'S MANUAL - Ridgid

More documents

Recommendations

Info

I P H P ULL LOOSE PARTS The following items are included with your band saw: V-Belt.................................................................................................................................................................................... 1 Saw Table ............................................................................................................................................................................. 1 Pulley Cover ......................................................................................................................................................................... 1 Motor with Switch ................................................................................................................................................................ 1 Band Saw ............................................................................................................................................................................. 1 Trunnion Support.................................................................................................................................................................. 1 Dust Chute ........................................................................................................................................................................... 1 Bevel Scale........................................................................................................................................................................... 1 Scale Indicator ..................................................................................................................................................................... 1 Rubber Grommet ................................................................................................................................................................. 4 Switch Key ........................................................................................................................................................................... 1 Blade Hanger........................................................................................................................................................................ 2 Lock Knob ............................................................................................................................................................................ 2 SAW TABLE TRUNNION SUPPORT BEVEL SCALE SCALE INDICATOR SWITCH KEY LOCK KNOB MOTOR WITH SWITCH BAND SAW ON P U L L U S OFF PULLEY COVER BLADE HANGER RUBBER GROMMET DUST CHUTE V- BELT Fig. 9 14
ASSEMBLY UNPACKING This product requires assembly. • Carefully remove the tool and any accessories from the box. Place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected the tool, identified all loose parts, and satisfactorily operated the tool. • Remove the protective oil that is applied to all unpainted metal surfaces. Use any ordinary household type grease and spot remover. • Apply coat of paste wax to the saw table. • The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in the operation and maintenance sections of this manual. • If any parts are damaged or missing, please call 1-866-539-1710 for assistance. WARNING: If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. • Put the leveling feet through the holes in the bottom of each leg. • Thread another hex nut on each of the leveling feet and hand tighten until they are next to the bottom support of the leg. LEG HEX NUTS LEVELING FOOT WARNING: To reduce the risk of injury from unexpected saw or work movement, leveling feet must be adjusted so that saw does not rock. After the band saw has been attached to the leg stand, it will be necessary to adjust the leveling feet. Fig. 10 WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. WARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. CARRIAGE BOLT LEG BRACE (LONG) WASHERS LOCK WASHERS LEG BRACE (SHORT) HEX NUTS LEG ATTACHING LEVELING FEET See Figure 10. • Locate the following items: 4 leveling feet 8 hex nuts, (3/8-16) • From the loose parts find the following items: 4 legs • Thread a hex nut on each of the leveling feet and screw it down towards the rubber foot. BASE Fig. 11 15
Page 1 and 2: ON I P U L L P U S H O 10° 0° 15
Page 3 and 4: GENERAL SAFETY RULES WARNING: Read
Page 5 and 6: SYMBOLS Some of the following symbo
Page 7 and 8: GLOSSARY OF TERMS Bevel Cut A cutti
Page 9 and 10: ELECTRICAL CHANGING MOTOR VOLTAGE S
Page 11 and 12: FEATURES KNOW YOUR BAND SAW See Fig
Page 13: LOOSE PARTS The following items are
Page 17 and 18: ASSEMBLY MOUNTING THE MOTOR ASSEMBL
Page 19 and 20: I ASSEMBLY MOUNTING THE SWITCH BOX
Page 21 and 22: ASSEMBLY • Replace throat plate a
Page 23 and 24: I P U L L P U S H O 0° 15° 30° 4
Page 25 and 26: OPERATION WARNING: Do not allow fam
Page 27 and 28: OPERATION TILTING THE TABLE See Fig
Page 29 and 30: I L P ADJUSTMENTS • Rotate guard
Page 31 and 32: MAINTENANCE LUBRICATION All the bea
Page 33 and 34: TROUBLESHOOTING Problem Cause Solut
Page 35 and 36: WARRANTY RIDGID ® HAND HELD AND ST

OPERATOR'S MANUAL - Ridgid

Create successful ePaper yourself

Delete template?

Save as template?