Manual 3060 System - SimonsVoss technologies

More documents

Recommendations

Info

PinCode Keypad 3068 Page 14 9.0 Opening In order to use the PinCode Keypad to open the associated locking, proceed as follows: Enter a PIN that has already been programmed. You are not permitted to wait more than 5 seconds between the entries of the individual numbers. In you have entered the correct number and the integrated transponder has been programmed, the LED lights GREEN and a signal is sounded. Then the integrated transponder opens the locking. 10.0 Meaning of the LED The built-in LED can light in one of three colours: green, yellow and red. These colours have the following meanings: • Green Digit that was input has been accepted PIN input was OK, which means that the correct PIN has been recognised, open signal is being sent PIN length OK PIN programming procedure was successful • Yellow battery warning • Red PIN input was incorrect Input of master code was incorrect Repeated incorrect input of the PIN (manipulation) PIN length was not entered correctly.
PinCode Keypad 3068 Page 15 11.0 Battery Warning To obtain a defined status for the PinCode Keypad and to minimise operating errors, a 2-level battery warning system has been integrated. When the battery capacity begins to drop, you will be notified of this in plenty of time to allow you to replace the batteries. Battery warning level 1: The opening procedure is carried out after a delay. The diode blinks YELLOW and the buzzer sounds for 10 seconds. The PinCode Keypad does not send the open command until after these 10 seconds. Battery warning level 2: In this case, the opening procedure is again carried out after a delay. The diode blinks YELLOW and the buzzer now sounds for 20 seconds. The PinCode Keypad does not send the open command until after these 20 seconds. You should not wait any longer to replace the battery. Otherwise, the system will stop functioning after a short time. 12.0 Battery Replacement In general, the batteries must be replaced by trained experts only. To do this, proceed as follows: 1. Completely unscrew the two screws in the bottom of the housing. 2. Remove the front of the housing. 3. Carefully release the battery clip from the printed circuit board (Figure 1). 4. Remove both batteries (Figure 1). 5. Insert the new batteries; the positive pole must be pointing up (Figure 2). 6. Carefully hook the battery clip back into the printed circuit board (Figure 3). 7. Put the housing back on. 8. Screw the two housing screws back into the housing from below. After you have replaced the batteries, all functions will be available again. Please always replace both batteries at the same time, because they have been charged to approximately the same level.
Page 1 and 2:
Manual 3060 System State of: July 2
Page 3 and 4:
Table of Contents Seite 2 P PEOPLE
Page 5 and 6:
Table of Contents Seite 4 WAVENET R
Page 7 and 8:
People to contact Page 2 SALES If y
Page 9 and 10:
Digital Locking System 3060 Registe
Page 11 and 12:
Digital Locking System 3060 Page 4
Page 13 and 14:
Digital Locking System 3060 Page 6
Page 15 and 16:
Transponder 3064 Content 1.0 Method
Page 17 and 18:
Transponder 3064 Page 4 1.2 Higher
Page 19 and 20:
Transponder 3064 Page 6 Explosion P
Page 21 and 22: Transponder 3064 Page 8 4.0 Battery
Page 23 and 24: Q3007 Biometric Transponder State o
Page 25 and 26: Q3007 Biometric Transponder Page 3
Page 37 and 38: MANUAL - BIOMETRIC READER Q3008 Pag
Page 59 and 60: PinCode Keypad 3068 State of : Sept
Page 61 and 62: PinCode Keypad 3068 Content 13.0 Sp
Page 63 and 64: PinCode Keypad 3068 Page 5 1.2 Prod
Page 65 and 66: PinCode Keypad 3068 Page 7 3.0 Star
Page 67 and 68: PinCode Keypad 3068 Page 9 4.3 Proc
Page 69 and 70: PinCode Keypad 3068 Page 11 6.2 Des
Page 71: PinCode Keypad 3068 Page 13 8.0 Res
Page 75 and 76: PinCode Keypad 3068 Page 17 13.0 Sp
Page 77 and 78: Digital Locking Cylinder 3061 VdS S
Page 79 and 80: Digital Locking Cylinder 3061 VdS P
Page 87 and 88: Manual - Digital locking cylinder 3
Page 117 and 118: Digital Half Cylinder 3061 Content
Page 119 and 120: Digital Half Cylinder Page 4 1.0 Me
Page 121 and 122: Digital Half Cylinder Page 6 4.0 Ba
Page 123 and 124:
Digital Half Cylinder Page 8 6.0 In
Page 125 and 126:
Digital Half Cylinder Page 10 6.4.2
Page 127 and 128:
Digital Half Cylinder Page 12 the f
Page 129 and 130:
DIGITAL HALF CYLINDER 3061 Status:
Page 131 and 132:
Manual - Digital Half Cylinder 3061
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Smart Relay: SREL, SREL.ZK, SREL.AK
Page 153 and 154:
Smart Relay: SREL, SREL.ZK, SREL.AD
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Smart Output Module Content 1.0 Imp
Page 175 and 176:
Smart Output Module Page 4 1.0 Impo
Page 177 and 178:
Smart Output Module Page 6 4.0 Befo
Page 179 and 180:
Smart Output Module Page 8 6.2 Conn
Page 181 and 182:
Smart Output Module Page 10 7.1 Sta
Page 183 and 184:
Smart Output Module Page 12 7.4 Pro
Page 185 and 186:
Smart Output Module Page 14 8.4 Adj
Page 187 and 188:
Smart Output Module Page 16 10.0 Te
Page 189 and 190:
VdS Shunt lock function 3066 Conten
Page 191 and 192:
VdS Shunt lock function 3066 Page 4
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Shunt lock function 3066 Operator I
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
WAVENET RADIO NETWORK 3065 Table of
Page 227 and 228:
WAVENET RADIO NETWORK 3065 Table of
Page 229 and 230:
WAVENET RADIO NETWORK 3065 Page 6 2
Page 231 and 232:
WAVENET RADIO NETWORK 3065 Page 8 4
Page 233 and 234:
WAVENET RADIO NETWORK 3065 Page 10
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
LON - Network 3065 State of: Septem
Page 265 and 266:
LON - Network 3065 Content 7.0 Repe
Page 267 and 268:
LON - Network 3065 Page 5 1.1 Gener
Page 269 and 270:
LON - Network 3065 Page 7 2.0 The S
Page 271 and 272:
LON - Network 3065 Page 9 4.0 Lock
Page 273 and 274:
LON - Network 3065 Page 11 Connect
Page 275 and 276:
LON - Network 3065 Page 13 5.0 LPI-
Page 277 and 278:
LON - Network 3065 Page 15 5.3 LPI-
Page 279 and 280:
LON - Network 3065 Page 17 Build th
Page 281 and 282:
LON - Network 3065 Page 19 6.3 Inst
Page 283 and 284:
LON - Network 3065 Page 21 9.0 Netw
Page 285 and 286:
LON - Network 3065 Page 23 9.6 Cabl
Page 287 and 288:
LON - Network 3065 Page 25 10.2 Net
Page 289 and 290:
LON - Network 3065 Page 27 12.0 Ans
Page 291 and 292:
LON - Network 3065 Page 29 13.0 Dat
Page 293 and 294:
LON - Network 3065 Page 31 Protecti
Page 295 and 296:
Programming Transponder 3067 Conten
Page 297 and 298:
Programming Transponder 3067 Page 4
Page 299 and 300:
Programming Transponder 3067 Page 6
Page 301 and 302:
PalmCD2 Programming Device State of
Page 303 and 304:
PalmCD2 Programming Device Page 3 1
Page 305 and 306:
SmartCD Programming Device State of
Page 307 and 308:
SmartCD Programming Device Page 3 1
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Caption State of: July 2007
Page 317 and 318:
Caption Page 3 SmartCD Password tra
show all

Manual 3060 System - SimonsVoss technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?