Manual 3060 System - SimonsVoss technologies

More documents

Recommendations

Info

LON – Network 3065 Page 20 7.0 Repeater 7.1 Method of Operation The repeater increases the allowable communication distance by regenerating the signals. Unlike routers, the repeater does not have a group ID, so it does not have to be configured by <strong>SimonsVoss</strong>. 7.2 Assembly Instructions Install it in a small housing that is suitable for DIN rail assembly. Connect the (LON) network lines to terminal screws on both sides. The power supply – which can be either AC or DC – is on one side of the housing. Feed the cable screen through to the opposite side. The repeater always needs a separate power supply, which is not included in the delivery!!! Repeaters, as they come from the factory, do not have any over voltage protection. For this reason, this protection should be already provided for by the customer. 8.0 Terminators To avoid disturbances, you must use a so-called terminator (pullup resistor) in the bus system as the segment termination. Connect this pull-up resistor to terminals 1 and 2 of the last LockNode and also to the network equipotential bonding.
LON – Network 3065 Page 21 9.0 Network Cable 9.1 General Information Every LockNode is networked with one line consisting of two twisted wires (twisted pair). The data and the supply voltage are both transmitted over this line (see Fig. on page N2 or N3). An LPI-10 or LPI-10 Compact module feeds the twisted pair line with voltage (approximately 48 V DC). 9.2 Cable Laying There are almost no restrictions placed on the cable laying when the given cable types are used. As a matter of principle, however, placement parallel to cables with strongly pulsating high voltage should be avoided. If, however, due to structural reasons, it is possible to use only cable that has already been laid but which either does not meet the required demands or which meets them only partially, the result can be interference due to radiation from other cables or systems. This interference can affect the performance capability of the network or can even lead to a complete network blackout. Therefore, it is important in these cases to pay special attention to cables or external systems that are in the vicinity of the transmission cable. This means high power machine systems, elevators, microwave systems, or transmission systems, for example. Connect the shields of all network cables to one another. Normally, these are connected to the potential compensation on the LPI-10. 9.3 Cable Types The type cable that you use depends on the following factors: 1. Total cable length (from the CentralNode to the last LockNode) 2. Cable length between the LockNodes 3. Network topology: wiring plan (star or bus system) With no topology With no topology Bus topology with terminators Total length Distance between Total length nodes JY (ST) Y 2x2x0.8 500 m 320 m 900 m Category 5 450 m 250 m 900 m
Page 1 and 2:
Manual 3060 System State of: July 2
Page 3 and 4:
Table of Contents Seite 2 P PEOPLE
Page 5 and 6:
Table of Contents Seite 4 WAVENET R
Page 7 and 8:
People to contact Page 2 SALES If y
Page 9 and 10:
Digital Locking System 3060 Registe
Page 11 and 12:
Digital Locking System 3060 Page 4
Page 13 and 14:
Digital Locking System 3060 Page 6
Page 15 and 16:
Transponder 3064 Content 1.0 Method
Page 17 and 18:
Transponder 3064 Page 4 1.2 Higher
Page 19 and 20:
Transponder 3064 Page 6 Explosion P
Page 21 and 22:
Transponder 3064 Page 8 4.0 Battery
Page 23 and 24:
Q3007 Biometric Transponder State o
Page 25 and 26:
Q3007 Biometric Transponder Page 3
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
MANUAL - BIOMETRIC READER Q3008 Pag
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
PinCode Keypad 3068 State of : Sept
Page 61 and 62:
PinCode Keypad 3068 Content 13.0 Sp
Page 63 and 64:
PinCode Keypad 3068 Page 5 1.2 Prod
Page 65 and 66:
PinCode Keypad 3068 Page 7 3.0 Star
Page 67 and 68:
PinCode Keypad 3068 Page 9 4.3 Proc
Page 69 and 70:
PinCode Keypad 3068 Page 11 6.2 Des
Page 71 and 72:
PinCode Keypad 3068 Page 13 8.0 Res
Page 73 and 74:
PinCode Keypad 3068 Page 15 11.0 Ba
Page 75 and 76:
PinCode Keypad 3068 Page 17 13.0 Sp
Page 77 and 78:
Digital Locking Cylinder 3061 VdS S
Page 79 and 80:
Digital Locking Cylinder 3061 VdS P
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Manual - Digital locking cylinder 3
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Digital Half Cylinder 3061 Content
Page 119 and 120:
Digital Half Cylinder Page 4 1.0 Me
Page 121 and 122:
Digital Half Cylinder Page 6 4.0 Ba
Page 123 and 124:
Digital Half Cylinder Page 8 6.0 In
Page 125 and 126:
Digital Half Cylinder Page 10 6.4.2
Page 127 and 128:
Digital Half Cylinder Page 12 the f
Page 129 and 130:
DIGITAL HALF CYLINDER 3061 Status:
Page 131 and 132:
Manual - Digital Half Cylinder 3061
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Smart Relay: SREL, SREL.ZK, SREL.AK
Page 153 and 154:
Smart Relay: SREL, SREL.ZK, SREL.AD
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Smart Output Module Content 1.0 Imp
Page 175 and 176:
Smart Output Module Page 4 1.0 Impo
Page 177 and 178:
Smart Output Module Page 6 4.0 Befo
Page 179 and 180:
Smart Output Module Page 8 6.2 Conn
Page 181 and 182:
Smart Output Module Page 10 7.1 Sta
Page 183 and 184:
Smart Output Module Page 12 7.4 Pro
Page 185 and 186:
Smart Output Module Page 14 8.4 Adj
Page 187 and 188:
Smart Output Module Page 16 10.0 Te
Page 189 and 190:
VdS Shunt lock function 3066 Conten
Page 191 and 192:
VdS Shunt lock function 3066 Page 4
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Shunt lock function 3066 Operator I
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
WAVENET RADIO NETWORK 3065 Table of
Page 227 and 228:
WAVENET RADIO NETWORK 3065 Table of
Page 229 and 230:
WAVENET RADIO NETWORK 3065 Page 6 2
Page 231 and 232: WAVENET RADIO NETWORK 3065 Page 8 4
Page 233 and 234: WAVENET RADIO NETWORK 3065 Page 10
Page 263 and 264: LON - Network 3065 State of: Septem
Page 265 and 266: LON - Network 3065 Content 7.0 Repe
Page 267 and 268: LON - Network 3065 Page 5 1.1 Gener
Page 269 and 270: LON - Network 3065 Page 7 2.0 The S
Page 271 and 272: LON - Network 3065 Page 9 4.0 Lock
Page 273 and 274: LON - Network 3065 Page 11 Connect
Page 275 and 276: LON - Network 3065 Page 13 5.0 LPI-
Page 277 and 278: LON - Network 3065 Page 15 5.3 LPI-
Page 279 and 280: LON - Network 3065 Page 17 Build th
Page 281: LON - Network 3065 Page 19 6.3 Inst
Page 285 and 286: LON - Network 3065 Page 23 9.6 Cabl
Page 287 and 288: LON - Network 3065 Page 25 10.2 Net
Page 289 and 290: LON - Network 3065 Page 27 12.0 Ans
Page 291 and 292: LON - Network 3065 Page 29 13.0 Dat
Page 293 and 294: LON - Network 3065 Page 31 Protecti
Page 295 and 296: Programming Transponder 3067 Conten
Page 297 and 298: Programming Transponder 3067 Page 4
Page 299 and 300: Programming Transponder 3067 Page 6
Page 301 and 302: PalmCD2 Programming Device State of
Page 303 and 304: PalmCD2 Programming Device Page 3 1
Page 305 and 306: SmartCD Programming Device State of
Page 307 and 308: SmartCD Programming Device Page 3 1
Page 315 and 316: Caption State of: July 2007
Page 317 and 318: Caption Page 3 SmartCD Password tra
show all

Manual 3060 System - SimonsVoss technologies

Create successful ePaper yourself

Delete template?

Save as template?