Safety Manager Safety Manual - Tuv-fs.com

More documents

Recommendations

Info

Document Release Issue Date EP-SM.MAN.6283 131 4.2 October 2008 Notice This document contains Honeywell proprietary information. Information contained herein is to be used solely for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or disclosed to a third party without the express permission of Honeywell Safety Management Systems. While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a purpose and makes no express warranties except as may be stated in its written agreement with and for its customer. In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information and specifications in this document are subject to change without notice. Copyright 2008 – Honeywell Safety Management Systems, a division of Honeywell Aerospace B.V. Honeywell trademarks Experion PKS ® , PlantScape ® , SafeBrowse ® , TotalPlant ® and TDC 3000 ® are U.S. registered trademarks of Honeywell International Inc. Other trademarks Microsoft and SQL Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Trademarks that appear in this document are used only to the benefit of the trademark owner, with no intention of trademark infringement. Conventions Symbols The following symbols are used in Safety Manager documentation: Attention This symbol is used for information that emphasizes or supplements important points of the main text. ii
Tip This symbol is used for useful, but not essential, suggestions. Note This symbol is used to emphasize or supplement important points of the main text. Caution This symbol warns of potential damage, such as corruption of the database. Warning This symbol warns of potentially hazardous situations, which, if not avoided, could result in serious injury or death. ESD This symbol warns for danger of an electro-static discharge to which equipment may be sensitive. iii
Page 1: Safety Manager Safety Manual EP-SM.
Page 5 and 6: Contents 1 The Safety Manual 1 Cont
Page 7 and 8: The Safety Manual 1 Content of Safe
Page 9 and 10: Basic skills and knowledge Basic sk
Page 11 and 12: Safety standards for Process & Equi
Page 13 and 14: Safety standards for Process & Equi
Page 15 and 16: Architectural principle and standar
Page 17 and 18: Figure 3 Functional diagram: QMR ar
Page 19 and 20: Certification Certification The adv
Page 21 and 22: Standards compliance Standards comp
Page 23 and 24: Standards compliance IEC 60068-2-30
Page 25 and 26: Safety Manager fault detection and
Page 27 and 28: Shutdown at assertion of Safety Man
Page 29 and 30: SM Controller faults Table 4 Contro
Page 31 and 32: SM Controller faults Table 7 Contro
Page 33 and 34: SM IO faults SM IO faults Tip: For
Page 35 and 36: SM IO faults Digital output faults
Page 37 and 38: SM IO faults Table 13 on page 31 sh
Page 39 and 40: SM IO faults . The input compare er
Page 41 and 42: Calculation errors Sometimes, howev
Page 43 and 44: Safety Manager special functions 4
Page 45 and 46: Unit shutdown outputs The unit shut
Page 47 and 48: On-line modification On-line modifi
Page 49 and 50: SafeNet communication The maximum r
Page 51 and 52: SafeNet communication System respon
Page 53 and 54:
Special requirements for TUV-approv
Page 55 and 56:
12. To reduce the influence of dist
Page 57 and 58:
F&G applications F&G applications F
Page 59 and 60:
Fax Transmittal Fax Number: +31 (0)
show all

Safety Manager Safety Manual - Tuv-fs.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?