Dräger Polytron 3000 - ancb.it
Dräger Polytron 3000 - ancb.it
Dräger Polytron 3000 - ancb.it
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Intended Use<br />
Intended Use<br />
<strong>Dräger</strong> <strong>Polytron</strong> ® <strong>3000</strong> Transm<strong>it</strong>ter for electrochemical sensors<br />
— For stationary, continuous mon<strong>it</strong>oring of gas concentrations in ambient air, w<strong>it</strong>h<br />
built-in <strong>Dräger</strong>Sensor ® .<br />
— For indoor and outdoor use<br />
— For installation alternatively in Ex areas zone 0, 1, 2 or 22 corresponding to device<br />
category 1G, 2G, 3G, 3D or Class I, Class II, Div. 1 & 2 hazardous area.<br />
For further details, see the installation notes.<br />
Notes on use in zone 22:<br />
Valid for all <strong>Dräger</strong> <strong>Polytron</strong> <strong>3000</strong> versions (see II 3D identification marking on the identification tag) and the accessories Duct<br />
Mount K<strong>it</strong> (Order No. 8317150).<br />
ST–691–2002–1.eps<br />
Identification marking and safety data concerning dust explosion protection:<br />
0158 II 3D, IP6x T65 o C (–40 o C Ta +65 o C)<br />
Maximum supply voltage: 30 V DC<br />
As electrical equipment of the device class and category II 3D according to directive 94/9/EC, the transm<strong>it</strong>ter <strong>Dräger</strong> <strong>Polytron</strong><br />
<strong>3000</strong> can be installed and operated w<strong>it</strong>hout safety barriers in the ATEX Zone 22 (dust), if the following notes concerning safe<br />
use are taken into account.<br />
1. The category II 3D is only valid for the accordingly marked <strong>Dräger</strong> <strong>Polytron</strong> <strong>3000</strong> transm<strong>it</strong>ter.<br />
2. According to EN 50281-1-2, the transm<strong>it</strong>ter may not be installed in areas which are endangered by conductive, combustible<br />
dusts.<br />
3. The Transm<strong>it</strong>ter and the accessories must be enclosed according to IP 6x rating. Especially the locking screw (2 mm Allen<br />
screw) of the sensor bayonet ring tight enough to ensure that the bayonet ring is secured against unintended loosening.<br />
4. The <strong>Dräger</strong> <strong>Polytron</strong> <strong>3000</strong> transm<strong>it</strong>ter and the accessories have a maximum surface temperature of 65 o C and the IP 6x rating.<br />
The transm<strong>it</strong>ter must be installed and maintained according to valid regulations (e.g. in European countries according to EN<br />
50281-1-2).<br />
5. The transm<strong>it</strong>ter and the accessories may only be opened when off-circu<strong>it</strong> or outside the Ex area. This must always be observed<br />
when replacing the sensor!<br />
— Calibration by one person even in areas subject to explosion hazards.<br />
— For connection to <strong>Dräger</strong> central un<strong>it</strong>s or to a programmable logic controller (PLC) to warn against physiologically harmful<br />
gas concentrations.<br />
— The optional display on the transm<strong>it</strong>ter indicates the actual gas concentration and makes calibration easier.<br />
False alarms during calibration are avoided by a special maintenance mode w<strong>it</strong>h output of a maintenance signal.<br />
_______________<br />
® <strong>Polytron</strong> is a registered trademark of <strong>Dräger</strong>.<br />
<strong>Dräger</strong>Sensor is a registered trademark of <strong>Dräger</strong>.<br />
4