You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Effects List<br />
74: ENHANCER → DELAY<br />
76: FLANGER → DELAY<br />
fig.MFX-74<br />
fig.MFX-76<br />
L in<br />
R in<br />
Enhancer<br />
Enhancer<br />
Mix<br />
Mix<br />
Balance D<br />
Delay<br />
Feedback<br />
Balance D<br />
L out<br />
Balance W<br />
Balance W<br />
R out<br />
L in<br />
R in<br />
Balance D<br />
Feedback<br />
Flanger<br />
Balance D<br />
Balance W<br />
Balance W<br />
Balance D<br />
Delay<br />
Feedback<br />
Balance D<br />
L out<br />
Balance W<br />
Balance W<br />
R out<br />
Parameter Value Description<br />
Enhancer Sens 0–127 Sensitivity of the enhancer<br />
Enhancer Mix 0–127<br />
Delay Time<br />
Delay<br />
Feedback<br />
Delay HF Damp<br />
Delay Balance<br />
fig.MFX-75<br />
0–2600 ms, note<br />
-98– +98%<br />
200–8000 Hz,<br />
BYPASS<br />
D100:0W–D0:100W<br />
Level 0–127 Output Level<br />
75: CHORUS → DELAY<br />
L in<br />
R in<br />
Balance D<br />
Balance W<br />
Chorus<br />
Balance W<br />
Balance D<br />
Level of the overtones generated<br />
by the enhancer<br />
Adjusts the delay time from the<br />
direct sound until the delay<br />
sound is heard.<br />
Adjusts the proportion of the delay<br />
sound that is fed back into the<br />
effect. Negative (-) settings will<br />
invert the phase.<br />
Adjusts the frequency above<br />
which sound fed back to the effect<br />
will be cut. If you do not want<br />
to cut the high frequencies, set<br />
this parameter to BYPASS.<br />
Adjusts the volume balance between<br />
the sound that is sent<br />
through the delay (W) and the<br />
sound that is not sent through the<br />
delay (D).<br />
Balance D<br />
Delay<br />
Feedback<br />
Balance D<br />
L out<br />
Balance W<br />
Balance W<br />
R out<br />
Parameter Value Description<br />
Flanger Pre Delay<br />
0.0–100.0 ms<br />
Adjusts the delay time from when<br />
the direct sound begins until the<br />
flanger sound is heard.<br />
Flanger Rate 0.05–10.00 Hz, note Frequency of modulation<br />
Flanger Depth 0–127 Depth of modulation<br />
Flanger Feedback -98– +98%<br />
Flanger Balance<br />
Delay Time<br />
Delay<br />
Feedback<br />
Delay HF Damp<br />
Delay<br />
Balance<br />
D100:0W–D0:100W<br />
0–2600 ms, note<br />
-98– +98%<br />
200–8000 Hz,<br />
BYPASS<br />
D100:0W–D0:100W<br />
Level 0–127 Output Level<br />
Adjusts the proportion of the<br />
flanger sound that is fed back into<br />
the effect. Negative (-) settings will<br />
invert the phase.<br />
Volume balance between the direct<br />
sound (D) and the flanger<br />
sound (W)<br />
Adjusts the delay time from the direct<br />
sound until the delay sound is<br />
heard.<br />
Adjusts the proportion of the delay<br />
sound that is fed back into the<br />
effect. Negative (-) settings will invert<br />
the phase.<br />
Adjusts the frequency above<br />
which sound fed back to the effect<br />
will be cut. If you do not want to<br />
cut the high frequencies, set this<br />
parameter to BYPASS.<br />
Adjusts the volume balance between<br />
the sound that is sent through the delay<br />
(W) and the sound that is not sent<br />
through the delay (D).<br />
Parameter Value Description<br />
Chorus Pre<br />
Delay<br />
0.0–100.0 ms<br />
Adjusts the delay time from the direct<br />
sound until the chorus sound is<br />
heard.<br />
Chorus Rate 0.05–10.00 Hz, note Frequency of modulation<br />
Chorus Depth 0–127 Depth of modulation<br />
Chorus Balance<br />
Delay Time<br />
Delay<br />
Feedback<br />
Delay HF Damp<br />
Delay<br />
Balance<br />
D100:0W–D0:100W<br />
0–2600 ms, note<br />
-98– +98%<br />
200–8000 Hz,<br />
BYPASS<br />
D100:0W–D0:100W<br />
Level 0–127 Output Level<br />
Volume balance between the direct<br />
sound (D) and the chorus<br />
sound (W)<br />
Adjusts the delay time from the direct<br />
sound until the delay sound is<br />
heard.<br />
Adjusts the proportion of the delay<br />
sound that is fed back into the effect.<br />
Negative (-) settings will invert<br />
the phase.<br />
Adjusts the frequency above which<br />
sound fed back to the effect will be<br />
cut. If you do not want to cut the<br />
high frequencies, set this parameter<br />
to BYPASS.<br />
Adjusts the volume balance between<br />
the sound that is sent<br />
through the delay (W) and the<br />
sound that is not sent through the<br />
delay (D).<br />
80