Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
System Settings<br />
FILL UP<br />
The pedal will trigger a fill-in, and<br />
then the next variation will play<br />
(e.g., from MAIN “1” to “2”).<br />
Once you reach variation “4,”<br />
subsequent presses of the pedal<br />
will not change the variation any<br />
farther.<br />
SYSTEM D BEAM<br />
Parameter Value Explanation<br />
D Beam<br />
Sens<br />
0–127<br />
This sets the D Beam controller’s<br />
sensitivity. The higher the value set,<br />
the more readily the D Beam<br />
controller goes to into erect.<br />
FILL<br />
DOWN<br />
PERFORM<br />
UP<br />
The pedal will trigger a fill-in, and<br />
then the previous variation will play<br />
(e.g., from MAIN “4” to “3”).<br />
Once you reach variation “1,”<br />
subsequent presses of the pedal<br />
will not change the variation any<br />
farther.<br />
The pedal will switch to the next<br />
Performance (i.e., from PERFORM<br />
001 to 002).<br />
D Beam<br />
Assignable<br />
1<br />
Type<br />
D Beam<br />
Assignable<br />
2<br />
Type<br />
Refer to “Functions that can be assigned” (p. 35).<br />
SYSTEM D BEAM SOLO SYNTH<br />
Refer to “Solo Synth Parameters” (p. 34).<br />
Pedal<br />
Assign<br />
PERFORM<br />
DOWN<br />
FAV<br />
PERFORM<br />
UP<br />
FAV<br />
PERFORM<br />
DOWN<br />
The pedal will switch to the<br />
previous Performance (i.e., from<br />
PERFORM 002 to 001).<br />
The pedal will switch to the FAVORITE<br />
Performance of the next number or<br />
bank (e.g., from FAVORITE PERFORM<br />
BANK 1-1 to 1-2).<br />
The pedal will switch to the FAVORITE<br />
Performance of the previous number<br />
or bank (e.g., from FAVORITE<br />
PERFORM BANK 1-2 to 1-1).<br />
SYSTEM MIDI<br />
Parameter Value Explanation<br />
MIDI Tx<br />
Switch<br />
Upper Tx<br />
Channel<br />
Lower Tx<br />
Channel<br />
MIDI Rx<br />
Switch<br />
OFF, ON<br />
1–16<br />
1–16<br />
OFF, ON<br />
Refer to “MIDI Parameters” (p. 44).<br />
FAV<br />
TONE UP<br />
The pedal will switch to the<br />
FAVORITE Tone of the next number<br />
or bank (e.g., from FAVORITE<br />
TONE BANK 1-1 to 1-2).<br />
Upper Rx<br />
Channel<br />
Lower Rx<br />
Channel<br />
1–16<br />
1–16<br />
Pedal<br />
Polarity<br />
FAV<br />
TONE<br />
DOWN<br />
STANDARD,<br />
REVERSE<br />
The pedal will switch to the<br />
FAVORITE Tone of the previous<br />
number or bank (e.g., from<br />
FAVORITE TONE BANK 1-2 to 1-1).<br />
Switches the polarity of the pedal<br />
connected to the CONTROL PEDAL<br />
jack. Some pedals will operate in<br />
the opposite of the expected way<br />
when you press them. If you’re<br />
using this type of pedal, set this<br />
parameter to “REVERSE.” If you’re<br />
using a <strong>Roland</strong> pedal (without a<br />
polarity switch), use “STANDARD.”<br />
Tx<br />
Tx Pitch<br />
Bend<br />
Tx<br />
Modulation<br />
Tx<br />
Program<br />
Change<br />
Tx Clock<br />
Tx Start-<br />
Stop<br />
OFF, ON<br />
OFF, ON<br />
OFF, ON<br />
OFF, ON<br />
OFF, ON<br />
Refer to “MIDI Parameters” (p. 44).<br />
Hold<br />
Polarity<br />
STANDARD,<br />
REVERSE<br />
Switches the polarity of the pedal<br />
connected to the HOLD PEDAL<br />
jack. (See “Pedal Polarity,” above)<br />
Tx Song<br />
Position<br />
OFF, ON<br />
47