Cisco EnergyWise IOS Configuration Guide - Ipland

More documents

Recommendations

Info

snmp-server enable traps energywise Chapter 3 EnergyWise CLI Commands snmp-server enable traps energywise Use the snmp-server enable traps energywise global configuration command to enable the domain member to send Simple Network Management Protocol (SNMP) notifications for EnergyWise traps or inform the network management system (NMS) of requests. Use the no form of this command to return to the default setting. snmp-server enable traps energywise [event-occured] [level-change] [neighbor-added] [neighbor-deleted] no snmp-server enable traps energywise [event-occured] [level-change] [neighbor-added] [neighbor-deleted] Syntax Description event-occured level-change neighbor-added neighbor-deleted (Optional) Enable EnergyWise event traps. (Optional) Enable EnergyWise power-level change traps. (Optional) Enable EnergyWise traps when neighbors are added. (Optional) Enable EnergyWise traps when neighbors are removed. Command Default The sending of EnergyWise traps is disabled. Command Modes Global configuration Command History Release 12.2(33)SXI4 12.2(50)SE 12.2(52)SG 12.2(53)SE2 Modification This command was introduced on the Catalyst 6500 switches. See the Cisco IOS Release Notes for Cisco EnergyWise, EnergyWise Phase 2 for the specific devices. This command was introduced on the Catalyst 3750-E, 3750, 3560-E, 3560, and 2960 switches. This command was introduced on the Catalyst 4500 switches. This command was introduced on the Catalyst 3750-X and 3560-X switches. 15.0(1)M2 This command was introduced on Cisco Integrated Service Routers Generation 2 (ISR G2), including Cisco 3900, 2900, and 1900 ISRs. Usage Guidelines Use the snmp-server host global configuration command to specify the host (network management system [NMS]) that receives the traps. If you do not specify any keywords, all the EnergyWise traps are enabled. You can verify your setting by entering the show energywise or the show running-config privileged EXEC command. 3-22 Cisco EnergyWise Configuration Guide OL-19806-04
Chapter 3 EnergyWise CLI Commands snmp-server enable traps energywise Examples To send EnergyWise traps to the NMS: DomainMember(config)# snmp-server enable traps energywise To send only EnergyWise event traps to the NMS: DomainMember(config)# snmp-server enable traps energywise event-occured Related Commands Command Description show energywise Displays the EnergyWise settings and status. show running-config Displays the operating configuration. OL-19806-04 Cisco EnergyWise Configuration Guide 3-23
Page 1 and 2:
Cisco EnergyWise IOS Configuration
Page 3 and 4:
CONTENTS Preface vii Conventions vi
Page 5 and 6:
Contents APPENDIX A Cisco EnergyWis
Page 7 and 8:
Preface This document describes how
Page 9 and 10:
Preface Related Publications For in
Page 11 and 12:
CHAPTER 1 Understanding Cisco Energ
Page 13 and 14:
Chapter 1 Understanding Cisco Energ
Page 15 and 16: Chapter 1 Understanding Cisco Energ
Page 17 and 18: CHAPTER 2 Configuring EnergyWise
Page 19 and 20: Chapter 2 Configuring EnergyWise Co
Page 21 and 22: Chapter 2 Configuring EnergyWise Ma
Page 29 and 30: Chapter 2 Configuring EnergyWise Us
Page 35 and 36: Chapter 2 Configuring EnergyWise Qu
Page 41 and 42: Chapter 2 Configuring EnergyWise Wa
Page 43 and 44: Chapter 2 Configuring EnergyWise Di
Page 45 and 46: CHAPTER 3 EnergyWise CLI Commands
Page 47 and 48: Chapter 3 EnergyWise CLI Commands c
Page 49 and 50: Chapter 3 EnergyWise CLI Commands d
Page 51 and 52: Chapter 3 EnergyWise CLI Commands e
Page 65: Chapter 3 EnergyWise CLI Commands e
Page 69 and 70: Chapter 3 EnergyWise CLI Commands s
Page 75 and 76: CHAPTER 4 Troubleshooting EnergyWis
Page 77 and 78: APPENDIXA Cisco EnergyWise and Cata
Page 79 and 80: APPENDIXB Cisco EnergyWise and Cata
Page 81 and 82: APPENDIXC Important Notice • Disc
Page 83 and 84: Appendix C Important Notice Stateme
show all

Cisco EnergyWise IOS Configuration Guide - Ipland

Create successful ePaper yourself

Delete template?

Save as template?