March 4, 2013 - Cabarrus County
March 4, 2013 - Cabarrus County March 4, 2013 - Cabarrus County
Does your bid comply? Yes __X__ No_____ Body Trim The following fixtures shall be added to the module shell for body protection and enhanced appearance. All items to be constructed of a minimum .100" thick bright polished aluminum tread plate with a minimum alloy property of #3003. All diamond plate trim shall be attached with 3/16” aluminum rivets and shall consist of the following: (A). Radius formed diamond-plate corner guards on all four corners with a minimum height of 10 inches. (B). Aluminum diamond plate rails shall be installed at the bottom edge on each side of the body. Rub rails are to be bolted on the 2” x 3” aluminum extruded tubes for ease of replacement and shall be spaced away from body .125" to prevent forming a dirt trap. (C). A diamond-plate liner shall fully encase all sides and bottom of the side step entrance well. Corner seams of this liner shall be MIG or TIG welded to insure a watertight, flushable-type stepwell. (D). A full width rear diamond-plate kick plate shall be installed from the rear step to the bottom of the rear doors. (E). An aluminum open grip strut step with individual diamond-plate end caps shall be installed at the rear loading doors. Step to be non-flexing and shall pivot upward by means of a full width stainless steel hinge. Rear bumpers without the center flip up section are not acceptable. End cap pod framework to be constructed of 2" x 3" steel closed tube, corner braced and welded to chassis frame. Bumper shall not exceed 9” from front to rear, and must not be mounted flush against the kick plate. (F). An aluminum polished fender shall be installed at each modular wheel well opening. The flare shall provide additional body protection and shall be installed in such a manner as not to rub the rear tires. (G). Extruded drip rails shall be installed above all exterior compartments. These drip rails shall be attached in such a manner to provide quick and easy replacement. They shall not be riveted, welded, or an integral part of the door frame extrusion. (H). A recessed polished cast aluminum fill guard shall be installed at the gas fill opening in the street side of the module. There shall be a stainless steel drip panel below. (I). To reduce the probability of corrosion and oxidation around the trim mounting points, each mounting area will be treated with ECK. Does your bid comply with lines “A” through “I”? Yes __X__ No_____ 48 Attachment number 1 4-4 Page 82
Floor The sub floor of module body shall be .125 inch 5052-H32 alloy rated aluminum securely welded to the wall structures and exterior compartments, and completely sealed from outside elements. Does your bid comply? Yes __X__ No_____ Over the aluminum sub-floor there shall be a one-piece top floor of ¾” exterior-grade solid cross-band plywood. This shall be securely anchored to the sub-floor by #8 x 1.5" floor screws. The flooring shall extend the full length and width of the patient compartment, including the space under the cabinets. Does your bid comply? Yes __X__ No_____ Floor Covering and Color The floor covering shall be Lon Plate II heavy duty flooring requiring a minimum of service yet completely water and detergent proof. This covering shall be of a color that matches and compliments the color scheme of the interior. The flooring shall extend the full length and width of the patient compartment and be rolled up the sides of the squad bench and street side cabinet 3 inches. A cove molding reinforcement is required behind the roll up in the floor. Does your bid comply? Yes __X__ No_____ Step well (side door) The curbside door step well shall be automatically lit with a clear LED when the side or rear doors are opened. The step-well shall be finished with highly polished aluminum diamond-plate with a removable grip strut section for safety and access to clean. It shall be at least as wide as the door opening, and as deep as possible, determined by the chassis frame. Inside the door, on the front of the ALS cabinet there shall be a stainless steel assist handle, 1-1/4 inch diameter. 49 Attachment number 1 4-4 Page 83
- Page 31 and 32: Section II. A. Special appropriatio
- Page 33 and 34: CABARRUS COUNTY BOARD OF COMMISSION
- Page 35 and 36: Specifications for a Type 1 (conven
- Page 37 and 38: When submitting their Bid Proposal,
- Page 39 and 40: Scope This specification covers a n
- Page 41 and 42: Does your bid comply? Yes __X__ No_
- Page 43 and 44: All bid prices and conditions must
- Page 45 and 46: The term "heavy-duty" as used to de
- Page 47 and 48: Front Suspension - front independen
- Page 49 and 50: Trailer tow hooks - front (2) Wheel
- Page 51 and 52: ventilated with clean air. The syst
- Page 53 and 54: Engine High-Idle Speed Control, Aut
- Page 55 and 56: Does your bid comply? Yes __X__ No_
- Page 57 and 58: Mud Flaps In order to provide addit
- Page 59 and 60: Driver's Compartment Controls The F
- Page 61 and 62: Does your bid comply? Yes __X__ No_
- Page 63 and 64: Circuit Connections Circuit connect
- Page 65 and 66: Does your bid comply? Yes __X__ No_
- Page 67 and 68: control console and will be an inte
- Page 69 and 70: Each compartment and module entry d
- Page 71 and 72: There shall be provided a clear LED
- Page 73 and 74: The vertical corner posts and the r
- Page 75 and 76: Does your bid comply? Yes __X__ No_
- Page 77 and 78: Side Window There shall be a fixed
- Page 79 and 80: (Q). Each compartment door shall ha
- Page 81: Dimensions given here are applicabl
- Page 85 and 86: Patient Compartment Carbon Monoxide
- Page 87 and 88: eak angles and locations to be pre-
- Page 89 and 90: Cabinet Layout See drawings accompa
- Page 91 and 92: controlled by a low voltage switch
- Page 93 and 94: Two (2) 100-watt Cast SA4319 speake
- Page 95 and 96: of F3963 and F3964 etch primer. The
- Page 97 and 98: CABARRUS COUNTY BOARD OF COMMISSION
- Page 99 and 100: EXTRACT FROM MINUTES OF PUBLIC HEAR
- Page 101 and 102: EXTRACT FROM MINUTES OF MEETING BOA
- Page 103 and 104: the aggregate principal amount of t
- Page 105 and 106: date for such interest, pursuant to
- Page 107 and 108: Section 6. following form: The Bond
- Page 109 and 110: of any Bond to be redeemed shall be
- Page 111 and 112: [The following four paragraphs are
- Page 113 and 114: The Bond Registrar shall not be req
- Page 115 and 116: ASSIGNMENT FOR VALUE RECEIVED the u
- Page 117 and 118: thereof shall also set forth, if le
- Page 119 and 120: time Bonds in accordance with the p
- Page 121 and 122: the best interests of the County in
- Page 123 and 124: (d) (6) adverse tax opinions, the i
- Page 125 and 126: proceeds of the Bonds, and to perfo
- Page 127 and 128: BUDGET AMENDMENT REQUIRED: Yes COUN
- Page 129 and 130: Totalnumberofinspections July Augus
- Page 131 and 132: REVISED Buildings %Change HousingUn
Floor<br />
The sub floor of module body shall be .125 inch 5052-H32 alloy rated aluminum securely welded to the wall<br />
structures and exterior compartments, and completely sealed from outside elements.<br />
Does your bid comply?<br />
Yes __X__ No_____<br />
Over the aluminum sub-floor there shall be a one-piece top floor of ¾” exterior-grade solid cross-band<br />
plywood. This shall be securely anchored to the sub-floor by #8 x 1.5" floor screws. The flooring shall extend<br />
the full length and width of the patient compartment, including the space under the cabinets.<br />
Does your bid comply?<br />
Yes __X__ No_____<br />
Floor Covering and Color<br />
The floor covering shall be Lon Plate II heavy duty flooring requiring a minimum of service yet completely<br />
water and detergent proof. This covering shall be of a color that matches and compliments the color scheme<br />
of the interior. The flooring shall extend the full length and width of the patient compartment and be rolled<br />
up the sides of the squad bench and street side cabinet 3 inches. A cove molding reinforcement is required<br />
behind the roll up in the floor.<br />
Does your bid comply?<br />
Yes __X__ No_____<br />
Step well (side door)<br />
The curbside door step well shall be automatically lit with a clear LED when the side or rear doors are opened.<br />
The step-well shall be finished with highly polished aluminum diamond-plate with a removable grip strut<br />
section for safety and access to clean. It shall be at least as wide as the door opening, and as deep as possible,<br />
determined by the chassis frame.<br />
Inside the door, on the front of the ALS cabinet there shall be a stainless steel assist handle, 1-1/4 inch<br />
diameter.<br />
49<br />
Attachment number 1<br />
4-4<br />
Page 83