March 4, 2013 - Cabarrus County
March 4, 2013 - Cabarrus County March 4, 2013 - Cabarrus County
(F). All doors shall have full-length stainless steel hinges with a .250" diameter pins. Stainless steel hinges shall be punch slotted for vertical and horizontal adjustments and attached with stainless steel screws. A layer of “ECK” must be applied on both sides of the hinge attachment. (G). All doors shall close on a continuous, extruded rubber gasket complex mounted on the inner flange of the door extrusion. The interior edge of the doorjamb shall be specifically engineered to provide a flat sealing surface around the entire perimeter of the door opening. This specialized design provides an unbroken, full perimeter seal outside the door latching assembly to enhance the watertight integrity of each door. Seals that are glued on or are mounted to the compartment doorjambs will be unacceptable due to their tendency to be torn by loading or unloading onboard equipment. (H). All access doors to be insulated with 1.875" Styrofoam. (I). The interior door panel of the exterior compartment doors shall be of highly polished aluminum diamondplate. (J). Patient entry and compartment door interior panels shall be .125" thickness, 5052-H32 aluminum attached to exterior door extrusion by ¼” - 20 machine screws with yellow Loctite and matching thread inserts installed around the perimeter of each door. All door panels shall be cut by computer-operated machines to ensure the exact location of windows, locks and even the mounting holes for the screws that attach the liner to the doorframes. This ensures that like doors will have the same door liners and that replacements, if needed, would fit exactly. The aluminum interior door panel shall be painted with Multispec paint color, covered with a clear coat, to harmonize with the interior colors. The use of self tapping screws is not allowed. (K). The interior surface of the module entry doors (rear and curbside) shall be finished in a safe and attractive manner that harmonizes with the interior appointments. The lower portion of this surface shall be a kick plate of stainless steel. Curbside door kick plate is to be 19 ” high with both rear door kick plates being 9” high. (L). A “V” shaped stainless steel assist handle shall be located the inside of each entry door. (N). The lower surface of the door jamb of each exterior compartment shall be trimmed with a stainless steel trim piece which conforms to the door sill and breaks over and down the side of the body behind the lower body rub rail. Similar trim pieces shall be applied to the curbside and rear entry doorsills. The side and rear thresholds shall be 6” minimum. To improve threshold seal, strengthen the threshold and prevent equipment snags or tripping, the side and rear thresholds will be fit with a 2° chamfer where the threshold meets the floor. (O). All cab and module entry and compartment doors (except the battery compartment) shall have electric locks powered by the OEM circuit. There shall be an unlock switch located in the front wall of the battery compartment. (P). Each door shall latch onto Nader pins at two points except for the battery compartment, which may latch at one point. 44 Attachment number 1 4-4 Page 78
(Q). Each compartment door shall have ¾” access holes with rubber plugs at each latch point for lubrication of the latches. Does your bid comply with lines “A” through “Q”? Yes __X__ No_____ Hold-Open Devices All compartment doors are to have dual action gas strut hold-opens. Does your bid comply Yes __X__ No_____ Exterior Storage Accommodations The ambulance shall be equipped with exterior compartments as shown in the drawings at the conclusion of this text. There shall be no more than a 3” dimension between door openings of adjacent compartments. Since the location of equipment and maximum space utilization is of prime importance to the Purchaser, the sizes and location of the various compartments required is necessary as shown. Deviations from the compartment layout or significantly smaller than shown are not acceptable and may be cause for rejection of the bid. Does your bid comply? Yes __X__ No_____ The exterior compartments shall be lockable with one key fitting all. They shall be equipped with the handle and door locks. Exterior door handl4es shall be Trimark chrome paddle latches with isolating gaskets. Each exterior compartment shall be automatically and individually lighted when the door is opened and shall activate the "compartment door" open warning light on the driver's console. The unit shall be wired so that only the light in the compartment that is open will be activated. Does your bid comply? Yes __X__ No_____ Compartment Construction All compartment top, sides and back panels must be a minimum thickness of .100 diamond-plate aluminum. Bottom of compartment must be .125” diamond-plate aluminum. Each compartment must be built as an 45 Attachment number 1 4-4 Page 79
- Page 27 and 28: CABARRUS COUNTY BOARD OF COMMISSION
- Page 29 and 30: Cabarrus County Budget Amendment Re
- Page 31 and 32: Section II. A. Special appropriatio
- Page 33 and 34: CABARRUS COUNTY BOARD OF COMMISSION
- Page 35 and 36: Specifications for a Type 1 (conven
- Page 37 and 38: When submitting their Bid Proposal,
- Page 39 and 40: Scope This specification covers a n
- Page 41 and 42: Does your bid comply? Yes __X__ No_
- Page 43 and 44: All bid prices and conditions must
- Page 45 and 46: The term "heavy-duty" as used to de
- Page 47 and 48: Front Suspension - front independen
- Page 49 and 50: Trailer tow hooks - front (2) Wheel
- Page 51 and 52: ventilated with clean air. The syst
- Page 53 and 54: Engine High-Idle Speed Control, Aut
- Page 55 and 56: Does your bid comply? Yes __X__ No_
- Page 57 and 58: Mud Flaps In order to provide addit
- Page 59 and 60: Driver's Compartment Controls The F
- Page 61 and 62: Does your bid comply? Yes __X__ No_
- Page 63 and 64: Circuit Connections Circuit connect
- Page 65 and 66: Does your bid comply? Yes __X__ No_
- Page 67 and 68: control console and will be an inte
- Page 69 and 70: Each compartment and module entry d
- Page 71 and 72: There shall be provided a clear LED
- Page 73 and 74: The vertical corner posts and the r
- Page 75 and 76: Does your bid comply? Yes __X__ No_
- Page 77: Side Window There shall be a fixed
- Page 81 and 82: Dimensions given here are applicabl
- Page 83 and 84: Floor The sub floor of module body
- Page 85 and 86: Patient Compartment Carbon Monoxide
- Page 87 and 88: eak angles and locations to be pre-
- Page 89 and 90: Cabinet Layout See drawings accompa
- Page 91 and 92: controlled by a low voltage switch
- Page 93 and 94: Two (2) 100-watt Cast SA4319 speake
- Page 95 and 96: of F3963 and F3964 etch primer. The
- Page 97 and 98: CABARRUS COUNTY BOARD OF COMMISSION
- Page 99 and 100: EXTRACT FROM MINUTES OF PUBLIC HEAR
- Page 101 and 102: EXTRACT FROM MINUTES OF MEETING BOA
- Page 103 and 104: the aggregate principal amount of t
- Page 105 and 106: date for such interest, pursuant to
- Page 107 and 108: Section 6. following form: The Bond
- Page 109 and 110: of any Bond to be redeemed shall be
- Page 111 and 112: [The following four paragraphs are
- Page 113 and 114: The Bond Registrar shall not be req
- Page 115 and 116: ASSIGNMENT FOR VALUE RECEIVED the u
- Page 117 and 118: thereof shall also set forth, if le
- Page 119 and 120: time Bonds in accordance with the p
- Page 121 and 122: the best interests of the County in
- Page 123 and 124: (d) (6) adverse tax opinions, the i
- Page 125 and 126: proceeds of the Bonds, and to perfo
- Page 127 and 128: BUDGET AMENDMENT REQUIRED: Yes COUN
(Q). Each compartment door shall have ¾” access holes with rubber plugs at each latch point for lubrication of<br />
the latches.<br />
Does your bid comply with lines “A” through “Q”?<br />
Yes __X__ No_____<br />
Hold-Open Devices<br />
All compartment doors are to have dual action gas strut hold-opens.<br />
Does your bid comply Yes __X__ No_____<br />
Exterior Storage Accommodations<br />
The ambulance shall be equipped with exterior compartments as shown in the drawings at the conclusion of<br />
this text. There shall be no more than a 3” dimension between door openings of adjacent compartments.<br />
Since the location of equipment and maximum space utilization is of prime importance to the Purchaser, the<br />
sizes and location of the various compartments required is necessary as shown. Deviations from the<br />
compartment layout or significantly smaller than shown are not acceptable and may be cause for rejection of<br />
the bid.<br />
Does your bid comply?<br />
Yes __X__ No_____<br />
The exterior compartments shall be lockable with one key fitting all. They shall be equipped with the handle<br />
and door locks. Exterior door handl4es shall be Trimark chrome paddle latches with isolating gaskets. Each<br />
exterior compartment shall be automatically and individually lighted when the door is opened and shall<br />
activate the "compartment door" open warning light on the driver's console. The unit shall be wired so that<br />
only the light in the compartment that is open will be activated.<br />
Does your bid comply?<br />
Yes __X__ No_____<br />
Compartment Construction<br />
All compartment top, sides and back panels must be a minimum thickness of .100 diamond-plate aluminum.<br />
Bottom of compartment must be .125” diamond-plate aluminum. Each compartment must be built as an<br />
45<br />
Attachment number 1<br />
4-4<br />
Page 79